Question about Mercedes-Benz Cars & Trucks

Open Question

Rack and pinion torque spec - Mercedes-Benz Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

Ad
  • 22 Answers

SOURCE: pinion nut torque spec chev

Axle Preload and Backlash Specifications 8.0 Axle Preload and Backlash Specifications Application
Specification
Metric
English
Backlash
0.08-0.25 mm
0.003-0.010 in
Backlash (Preferred)
0.13-0.18 mm
0.005-0.007 in
Pinion Bearing Preload, New Bearings
1.7-3.4 N·m
15-30 lb in
Pinion Bearing Preload, Used Bearings
1.1-2.3 N·m
10-20 lb in
Pinion and Differential Case Bearing Preload, New Bearings
3.4-6.2 N·m
30-55 lb in
Pinion and Differential Case Bearing Preload, Used Bearings
2.8-5.1 N·m
25-45 lb in

Posted on May 20, 2009

  • 109 Answers

SOURCE: rack & pinion replacement

there many web sites that offer tech suppurt, even Chrysler, just start looking, also Napa Auto Parts. Auto Zone. This is to hard to explain on a site like this. GOOD LUCK RDJRP

Posted on Aug 07, 2009

  • 1 Answer

SOURCE: rack and pinion removal and installation

it is sort of a strange deal but you have to remove the cowl and the wiper assembly and access it through there. You can get the step by step instructions from autozone

Posted on Oct 11, 2009

roniecon
  • 6927 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm looking for the torque wrench settings for the power steering rack mounting nuts for a au1998 xr6


They all still need to be checked with a torque wrench periodically. ... My BA XR6 has developed a clicking/knocking usually while turning while ... There is a torque setting for the nuts, it cast into the sub member near the mounts. ... Maybe thats all the mid-life b series steering click is, the bolts coming loose.

[PDF]BA Torque Specs

members.optusnet.com.au/~matt_l/tridocss_files/ba_torque_specs.pdf
Torque(Nm) Torque(FtLb) ... Cam chain tensioner blade to cylinder head nut ... Front and rear upper mounting bolts .... Front Suspension/Steering .... NOTE: In stages A and B a torque wrench of known and accurate calibration must be used.

Teleflex Mechanical Steering Tech Reference & FAQ

www.jamestowndistributors.com > Home > How Tos
I'm replacing a Teleflex rack & pinion cable in a 1985 boat. ... If you have installed a non-tilt "Back Mount Rack Helm," order Friction Kit part number ... Morse Command 200 Rack: use Teleflex Back Mount Rack for power-assisted or NFB Rack for ...torque feedback from the engine (which can make the steering wheel turn on ...

Dec 28, 2015 | Cars & Trucks

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

I need the tourqe setting for the connection from the tie rod end to the rack & pinion.


tie rod end torque settings. tie rod end and castllated nuts 35-46 ft lbs.

tie rod end jamb nut. 35-46 ft lbs.

rack and pinion. power rack and pinion subframe retaining bolts. 85-99 ft lbs.

good luck!

Nov 06, 2010 | 1998 Ford Taurus

1 Answer

How do you replace the steering rack on my 2001 Ford Windstar??


YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE YOU HAVE VECHICLE PARKED ON LEVEL SOLID GROUND.ONCE VECHICLE RAISED.REMOVE FRONT WHEELS.REMOVE TIE RODS END COTTER PINS AND CASTLE NUTS.REMOVE TIE ROD ENDS FROM THE KNUCKLES.REMOVE FRONT STABILIZER BAR.POSITION THE DASH OPENING WEATHER SEAL FOR THE STEERING COLUMN OUT OF THE WAY.REMOVE OR DISCONNECT THE FOLLOWING.REMOVE PINCH BOLT RETAINING THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING.REMOVE STEERING GEAR RETAINING NUTS BOLTS.REMOVE REAR SUBFRAME BOLTS.USE WIRE TO SUPPORT EXHAUST COMPONENTS UNLESS YOU ARE REMOVING THEM COMPLETELY.SUPPORT THE EXHAUST SYSTEM FLEX TUBE AND REMOVE THE FLEX TUBE TO DUAL CONVERTER Y PIPE ATTACHMENT.LOWER THE VECHICLE SLIGHTLY UNTIL THE REAR SUBFRAME SEPARATES FROM THE BODY APPROXIMATELY 4 INCHES.REMOVE THE HEAT SHIELD BAND AND FOLD THE HEAT SHIELD DOWN.ROTATE THE RACK AND PINION ASSEMBLY TO CLEAR THE BOLTS FROM THE FRONT SUBFRAME AND PULL TOWARD THE DRIVERS SIDE OF THE VECHICLE.PLACE A DRAIN PAN UNDER THE VECHICLE AND DISCONNECT THE POWER STEERING LINES.REMOVE THE RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE***** TO INSTALL ****** INSTALL NEW TEFLON O - RINGS ON THE POWER STEERING LINE FITTINGS. PLACE THE RACK AND PINION RETAINING BOLTS IN THE GEAR HOUSING.INSTALL RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE.INSTALL POWER STEERING LINES ON THE RACK AND PINION ASSEMBLY. INSTALL RACK AND PINION ASSEMBLY ON THE SUBFRAME.INSTALL ******** HEAT SHIELD.INSTALL TIE ROD ENDS TO THE KNUCKLES TIGHTEN THE CASTLE NUTS AND INSTALL THE COTTER PINS.INSTALL STABILIZER BAR.INSTALL RACK AND PINION ASSEMBLY RETAINING BOLTS.TORQUE THEM TO 85 - 99 FT LBS. RAISE VECHICLE UNTIL SUBFRAME CONTACTS THE BODY.INSTALL REAR SUBFRAME RETAINING BOLTS TORQUE THEM TO 83 - 112 FT LBS.INSTALL EXHAUST SYSTEM FLEX TUBE TO DUAL CONVERTER Y PIPE.INSTALL FRONT WHEELS.INSTALL A NEW PINCH BOLT IN THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING ON THE RACK INPUT SHAFT TORQUE PINCH BOLT TO 25 - 33 FT LBS.POSITION THE STEERING COLUMN OPENING WEATHER SEAL OVER THE STEERING GEAR HOUSING.LOWER THE VECHICLE FILL THE POWER STEERING FLUID RESERVOIR. START THE VECHICLE AND CHECK FOR LEAKS. CHECK FOR PROPER WHEEL ALIGNMENT AND STEERING WHEEL POSITION.BLEED POWER STEERING SYSTEM.

Oct 14, 2010 | 2001 Ford Windstar

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

What are the torque specs for the pinion nut and flange bolts on a 1990 ford f350 srw differential? Does anyone have diagrams or pics of how to remove and replace the pinion seal on the same model year...


Most pinion nuts don't have a published torque spec. they are to be tightened until the pinion requires a specified torque to spin with the wheels and brake drums removed. Often times, when a rebuild is not performed, it should be torqued to the same preload as before the work. autozone.com has alot of good repair info and diagrams.

Nov 17, 2009 | 1990 Ford F350

1 Answer

Torque Specifications


1. If you are speaking of the large yoke nut there is no "torque spec" per say, instead it is a rotational preload-

From Ford manual:
Use the special tool to hold the pinion flange while tightening the nut to set the preload.
  • Tighten the nut, rotating the pinion occasionally to ensure the differential pinion bearings are seating correctly. Take frequent differential pinion bearing preload readings by rotating the pinion with a Nm (inch-pound) torque wrench. The final reading must be 0.56 Nm (5 lb-in) more than the initial reading taken during removal.
2. If you are looking for the yoke straps that hold the universal in place to the yoke it is 14ft lb for the 4 bolts.

May 28, 2009 | 2004 Ford Ranger

1 Answer

Pinion nut torque spec chev


Axle Preload and Backlash Specifications 8.0 Axle Preload and Backlash Specifications Application
Specification
Metric
English
Backlash
0.08-0.25 mm
0.003-0.010 in
Backlash (Preferred)
0.13-0.18 mm
0.005-0.007 in
Pinion Bearing Preload, New Bearings
1.7-3.4 N·m
15-30 lb in
Pinion Bearing Preload, Used Bearings
1.1-2.3 N·m
10-20 lb in
Pinion and Differential Case Bearing Preload, New Bearings
3.4-6.2 N·m
30-55 lb in
Pinion and Differential Case Bearing Preload, Used Bearings
2.8-5.1 N·m
25-45 lb in

May 17, 2009 | 2006 Chevrolet Colorado

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78936 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...