Question about 1988 Chevrolet S-10

1 Answer

I need to know how to replace the door handle for my 1988 s10 pickup

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have to remove the 2 screws in the arm support, slide off, have to remove the hand crank (special tool needed here) and then pull off the door panels with special tool to pry the plastic clips out. Once the panel is off, put the window at its top position and unclip the plastic actuator that holds the rod into place. Undo the 2 selfcutting bolts and replace in the reverse.

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know what kinds of tools i will need and how to remove and replace the drivers door on my 98 S10 pickup


The door is held on my the pins hammer them out but disconnect wires and the stop first support the door or get someone to help I would get new pins

Mar 09, 2016 | Cars & Trucks

1 Answer

My passagner door will not open either way inside


If you have the linkage there and it is working, Then the latch is broke. Replace it.

Oct 19, 2014 | 1993 Chevrolet S-10

1 Answer

I need to replace passenger side rear veiw mirror on 1996 s10 pickup.. i need free manual showing how to remove door panels.


To remove the door panel, remove any screws that are in the vicinity of pull handles and door pockets. These screws will be under little trim covers that you need to prise off to get to their heads. Look for the screws around the edge of the panel and also the screw in the latch release handle recess.
The lock knob, if there is one there, will have to be screwed off and then carefully work your way around the door, freeing the panel's clips from their holes in the door frame. (Doot panels are brittle and clip break out easily).
Finally the panel will probably have to be lifted out if the window slot. (If the panel does not come off, work out what is retaining it and remove that screw or slide it off the clip that is still holding the panel. Disconnect any electrical plugs behind the panel. Under the panel you will find a plastic dust sheet that is stuck to the door frame, remove this carefully, you will have to replace it before replacing the panel.

Apr 27, 2011 | 1996 Chevrolet S-10 Pickup

1 Answer

I need to know the timing specs for a 1988 Chevy S10 Pickup 2.8


2.8L 10 BTDC .. this is with the 1 connector brown wire.. usually under the glove box, or under the hood behind the distributor.. disconnect that wire to set the timing..

Thanks for the vote.

Dec 22, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

How do I remove drivers side door panel on 1998 Chevy S10 pickup to repair/replace window regulator?


i think there are screws around the door handle on the in side that need to be taken off the the rest just pop out

Feb 01, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How do you remove a door panel from a 89 toyota pick up


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Aug 08, 2009 | 1988 Toyota Pickup

1 Answer

1988 Chevy S10 Durango Pickup, Won't start will fire


sounds like ignition module inside of distributor cap under distributor rotor button.these do go bad and can easily be replaced.strong suspicion from your details that this is the culprit.

May 09, 2009 | 1988 Chevrolet S-10

1 Answer

Door panel 1984 camaro


Yes that whole plate needs to come off. Be careful as some of those torx heads are just for show and not actual screws. The door handle also needs to be removed. There are three screws for the handle, usually a torx head. The door panel will then unclip and with the window down you can push in and pull up gently on the upper door trim (hard plastic part) to release the door panel from the door.

Feb 09, 2009 | 1988 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...