Question about 2006 Ford Ranger

1 Answer

My 06 ranger does not give any heat when switch is on i have tried everything i know but no go. they say bend door is stuck shut where is the bend door

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 170 Answers

It's a vacuum or 'door' problem, have a pro look at it, or buy a Haynes Manual and try to do it yourself.

Posted on Oct 15, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Window wont go up or down on my 1994 chevy pickup 1/2ton passenger window


Check wiring where door flexes. copper wires repeated bending can break.
Overload breaker points stuck - is inside motor.
Burned smell - replace motor.
Bad door switch - my rear window would freeze shut. trying top open would damage switch. Mine was driver door master switch.

Apr 21, 2014 | 1991 Buick Park Avenue

1 Answer

My 96 mitsubishi montero LS is having a a couple problems


the first problem is your idle air control vavle it is located on the thottle body . the idle air control vavles job is to have the engine run a little high to warm the engine ,and then shut off once engine warm. . the other is a your blend door is stuck open or close. you may have something stuck in it. the bend door motor is located in the heater box in the dash

Oct 31, 2012 | Mitsubishi Cars & Trucks

1 Answer

I have a 2006 Ford Ranger and the heat is stuck on on. Even when I move the handle to cool it still heats. Do you have any suggestions, thanks Al Shults.


Hello
This problem is caused by one or both of the following parts, one is the air temperature control blend door actuator motor, the next is the actual blend door, the shaft that the electric actuator moves is snapped off due to the door binding, both problems cause no air temperature control and you either get heat or cold with no control to change it. The problem is very common in the Ranger and the Explorer.

Dec 27, 2010 | 2006 Ford Ranger

1 Answer

I cannot locate the door ajar swich on my 99 ford ranger super cab


It's integral to the door latch. Is it stuck on saying the door is ajar? Spray some wd-40 into the latch and open and shut it a few times and it will clear up.

Mar 21, 2010 | 1999 Ford Ranger SuperCab

3 Answers

I have a '04 rio and the driver side door is stuck shut, when the manual lock pin is pulled up, it snaps back down like its on a rubber band.


JEB, Homestead Florida

Total credit to rfbqwerty

Have 2003 Kia Rio 1.6, door shut, locking pin springs back down, I followed rfbqwerty istructions to the Penny and it worked in about 20 minutes I was able to open the door. The restst is a POC, thanks a million!!!

Option found in Google 6/16/2012

rfbqwerty

03-28-2006, 06:22 AM
Easy method to open a stuck Kia Rio door. Full credit to 'fastkia' for explaining how to open a stuck lock but after opening my lock by his method I found an easier way to do the job. You need a piece of straight wire (clothes hanger is good) and make a 3/4 inch square bend on one end. Wind down the window & push a tapered (plastic) wedge between the glass and the inside rubber to get a gap to work through. Poke the wire down beside the glass and pull up on the lever that is operated by the outside door handle. This is not the wire from the door handle but is the lever the wire connects to in the lock. While the lever is held up by your hook you can now pull up the locking button. Remove the wire from the door and everything works and it can be opened and closed as often as you like but don't press the button or use the key lock or it will be stuck again. The lever is normally held up by a small spring that has a sharp bend at one end and the spring will ALWAYS break at this bend. I used the same spring with a 'new' loop made from a section of paper clip to replace the old loop. Better than the original. No cost and it took less than 30 minutes

Mar 09, 2010 | 2002 Kia Rio

2 Answers

99 grand cherokee door is shut but computer says


the door latch has a micro switch in it that has probably gone bad. if so the door latch assy will need replaced

Sep 26, 2009 | 1999 Jeep Grand Cherokee

4 Answers

Interior light stays on and door warning lamp


some where along the edge of the door there is a push button switch that is deactivated when the door is shut, turns light of and turns door warning lamp off. either at bottom rear of door or up by the hinges.

Aug 25, 2009 | 2000 Ford Ranger SuperCab

1 Answer

Wiring


check the door switches on both sides. One of them is probably shorted

Jul 06, 2008 | 1992 Ford Ranger

Not finding what you are looking for?
2006 Ford Ranger Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...