Question about Mercury Sable

1 Answer

Code po320 - Sable Mercury Cars & Trucks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 170 Answers

Go to auto parts store, they can tell you what the code is, or a Ford/Merc dealer can tell you what it means.

Posted on Oct 15, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2007 sport trac. What will fix codes po320 &

Faulty Ignition/Distributor engine speed sensor, Faulty Crankshaft Position sensor
Ignition/Distributor engine speed sensor harness is open or shorted, Ignition/Distributor engine speed sensor circuit poor electrical connection, Low battery charge, Faulty Engine Control Module (ECM)
try tightening the fuel cap if not replace it

Oct 19, 2014 | 2007 Ford Explorer Sport Trac

1 Answer

I have a code PO320

code p0320 refers to crankshaft position sensor(CKS) sensor/engine speed RPM sensor-circuit malfunction===causes --wiring---CKP/RPM sensor---ECM

Jun 10, 2014 | Hyundai XG350 Cars & Trucks

1 Answer

What does code PO320

According to my code manual PO 320 code means ,There is no signal to the crank shaft position (Sensor)

Nov 10, 2012 | 1998 Jeep Cherokee

1 Answer

Engine codes

Trouble Code: P0230

Fuel Pump Circuit Malfunction
Possible Causes:

Fuel pump control circuit is open or shorted to ground Fuel pump relay power circuit from ignition switch is open Fuel pump relay is damaged or has failed PCM has failed

Jun 02, 2012 | Hyundai Motor 2004 Sonata

1 Answer

Diagnostic code p0320

po320 is either the coil pack, the crank sensor or the cam sensor. po320 means--
Ignition Engine Speed Input Circuit Malfunction

Apr 22, 2012 | 1997 Mercury Cougar XR7

1 Answer

2003 Hyundai Santa Fe Still Will Not Start PO320 PO340

code p 0320 refers to crank shaft position sensor (CKP)/engine speed (RPM ) sensor---circuit malfunction====causes ---wiring---CKP/RPM sensor ---ECM
code p 0340 refers to camshaft position sensor (CMP) sensor A bank 1---circuit malfunction===causes wiring---CMP sensor ---ECM
following engine work , it is always best to check that all of the harness connections were assemble properly
check for broken wires during the work

Apr 29, 2017 | 2003 Hyundai Santa Fe

1 Answer

Our Jeep liberty Po320 code than misfire replaced parts and same codes again than stalls after it get warm. Could this be a PCM units

disconnecting the battery will only temporarily erase your code or check engine light. put your keys in the ignition, then turn it in the on position. Do not turn it so that the engine turns over, but as if you were just turning the radio on. Keep it on for 2 to 4 seconds repeat 40 times. i no it may take a while but unless you have a scanner its the only way.

Jan 16, 2010 | 2002 Jeep Liberty

2 Answers

Po320 code and code po303 2004 lincoln navigator

Replaced a camshaft sensor still running rough & engine light still on, 2004 lincoln nav. 5.4 liter

Jan 02, 2010 | 2004 Lincoln Navigator

1 Answer

How do i locate a crank sensor and the code comes up as po320. thank you

Yes the po320 code is no signal at the crank.It is located on the transmission bellhousing.Its on the lefthand side of the housing in the top quarter.At the back of the motor.After the problem has been fixed,do not disconnect the battery to clear the code.Get the codes cleared before starting the motor or the comp may set a trouble code for that.A scan tool is needed from a dealer or good shop.I hope this helps

Sep 25, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

80637 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides