Question about 1992 Oldsmobile Eighty Eight

1 Answer

Crankshaft sensor water pump put on now wont start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

Did you lock the engine before doing it?... check it the timing is correct.

Posted on Oct 15, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft position sensor located 1996 gmc sierra 1500


The crankshaft position sensor is located on the right-side (passenger side) of the engine. At the rear of the engine, behind the starter. You need to remove the starter to remove the crank sensor. Remember to disconnect the battery first. The starter can short against the cross member.

Mar 03, 2014 | Cars & Trucks

1 Answer

I replaced the water pump and the thermostat because i was having troble with the cooling system anyway i got everthing back together went to crank over the engine to start and the belt came off put the...


No, but the belt may have struck the crankshaft sensor. The sensor is behind the crankshaft pulley. Check the wires going back to the sensor and repair as needed. Let me know if you have more questions.

Jan 13, 2011 | 2000 Pontiac Montana

1 Answer

I PUT A NEW FUEL PUMP AND FILTER BUT MY SUBURBAN STILL WONT START i CAN PUT GAS IN AIR FILTER AND IT WILL START. ARE THEY A SENSOR THAT COULD BE BAD ?


If you hear the fuel pump come on when you put the key to the run position...then replace the crankshaft position sensor, I would also replace the camshaft position sensor as well because a failure there will have the same effect, and its cheap insurance against further breakdown. $80 for both at rockauto.com

When the crankshaft position sensor fails the engine will run for one second then shut off as if it ran out of gas.

Make sure your fuel pump is running; it should run about 5 seconds when you try to start the car. if not check the fuse and relay for the pump and the ground strap

Make sure your battery is in good condition with tight connections.

Oct 19, 2010 | 1996 GMC Suburban

2 Answers

My saab 9-5 wagon wont start


water temp switch faulty.

Jul 04, 2009 | 2000 Saab 9-3 Viggen

2 Answers

The car wont start it cranks but wont start


it could be the coil pack. you have to test it to find out. it also could be spark plugs wires, and a few other things. let me know what else you find

Apr 01, 2009 | 2000 Mitsubishi Eclipse

1 Answer

My car wont start I changed my water pump n now my car wont start


It is a good idea (recommended) to disconnect the battery when working on electrical components. If you disconnected the batter, make sure the battery cables are secure on the terminals (clean terminals if necessary) - apply a terminal grease to prevent corrosion and acid build up. Also, check the connection on the alternator - it's very possible this may have been disturbed or disconnected by accident during the installation of wires. Part of your message says "my car won't start, I changed my water..." did you change your water pump? There may be a crankshaft and/or camshaft sensor near the water pump. Make sure that these are plugged in and secure. Check your ignition fuse in the fuse box, the starter relay(under the hood) and the fusable link,next to or near the battery, or starter. Check all electrical connection that may prevent the vehicle from starting.

Mar 31, 2009 | 1991 Toyota Celica

1 Answer

1992 plymouth grand voyager wont stay running


i can tell you its not the fuel pump.if you smell fuel then the pump is working right,you may have a weak crankshaft sensor though which would keep it from starting and running. but its definately not the fuel pump maybe you have water in your gas

Dec 29, 2008 | 1992 Plymouth Grand Voyager

1 Answer

New water pump wont start


It could be the crankshaft position sensor located near the crankshaft under you sparkling new water pump. Wires may be disconnected.:) Good Luck

Dec 10, 2008 | 1989 Dodge Raider

1 Answer

91 Park Ave, wont crank


you may have disturbed the crankshaft or camshaft sensor

Oct 21, 2008 | 1991 Buick Park Avenue

2 Answers

Chevy blazer wont start 2002


if it turns over there are a cocuple of things to check. crankshaft sensor and the coil pack maybe the computer.id start with the crankshaft sensor

Jun 29, 2008 | 2002 Chevrolet Blazer

Not finding what you are looking for?
1992 Oldsmobile Eighty Eight Logo

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...