Question about Cars & Trucks

Open Question

My lab Resistivity "Core Testing Unit CTU-2" Scintrex Unit Does not Have A Manual showing Internal PBA in house curcuit Diagram To mend it

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
lpfaff1
  • 11573 Answers

SOURCE: gas gauge staying at empty when tank is full

Spencer, Check all fuses ,plugs and grounding at the tank.The sending unit module, inside the GM's gas tanks were notorious for going bad in this err, when you changed it did you use a quality part? Also the fuel pump sending unit plug/wire harnesses were known issues, so much that replacement pumps would often come with replacement plug to splice into existing harness. Check the attached links,instruction and guides on how to trouble shoot fuel gauge/sending unit, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
General Motors Fuel Gauge Troubleshooting American Autowire
GM Defective Gas Gauge Leaves Owners Guessing
Fuel Gauge Tech How To Properly Diagnose Faulty Fuel Pump Sending Unit
GM Fuel Pump Level Sensor Diagnosis Testing

Posted on Aug 27, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replacing heater core in 2006 sazuki forenza



Heater Core Removal and Installation

Removal
1. Disconnect the negative battery cable.
2. Remove the instrument panel.
3. Recover the refrigerant.
4. Remove the heater/air distributor case assembly.
5. Remove the wiring harness and electrical connectors from the heater/air distributor case assembly.


6. Remove the screws that connect the heater core housing and the evaporator housing.


7. Separate the sponge from heater/air distributor case assembly.
8. Remove the heater core cover screws from the heater core housing.


9. Remove the heater core.

Installation
1. Install the heater core into the case.
2. Install the screws on the heater core housing.

Tighten: Tighten the heater core cover screws to 1.2 Nm (11 in. lbs.).

Jan 10, 2017 | 2006 Suzuki Forenza

1 Answer

Gas gauge staying at empty when tank is full


Spencer, Check all fuses ,plugs and grounding at the tank.The sending unit module, inside the GM's gas tanks were notorious for going bad in this err, when you changed it did you use a quality part? Also the fuel pump sending unit plug/wire harnesses were known issues, so much that replacement pumps would often come with replacement plug to splice into existing harness. Check the attached links,instruction and guides on how to trouble shoot fuel gauge/sending unit, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
General Motors Fuel Gauge Troubleshooting American Autowire
GM Defective Gas Gauge Leaves Owners Guessing
Fuel Gauge Tech How To Properly Diagnose Faulty Fuel Pump Sending Unit
GM Fuel Pump Level Sensor Diagnosis Testing

Aug 27, 2016 | 2000 Oldsmobile Alero

1 Answer

Troubleshoot wipers


Best if you have a wiring diagram of at least the part of
the curcuit your going to work on (wiper circuit)

That applies to any electrical issue,simply can't start your
checking or testing without a road map.

If it were to guess for you,I would say the motor has failed

Even with a wiring diagram it isn't always easy to jump it
once out of the car,to test it. You won't have the internal
wiring diagram for the motor.

The switch you can turn on & use your volt meter at the
wiper motor with it disconnected,but again need to have the
diagram to probe the correct wires

Dec 08, 2012 | 1991 Ford Escort

1 Answer

How To Install a Heater Core in a '94 Eagle Vision ESI 3.3


Hello , for heater core or AC evaporator ,, you have to remove the dashboard to reach the housing and replaced them .. no other way

Oct 13, 2017 | 1994 Eagle Vision

1 Answer

How do I remove heater core on 1997 dodge stratus


prev.gif next.gif Heater Core REMOVAL & INSTALLATION Cirrus, Stratus, Sebring Convertible and Breeze
  1. Disconnect the negative battery cable.
  2. Remove the radio/HVAC control module bezel. CAUTION
    The vehicles covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses air bags. Whenever working near any of the SRS components, such as the impact sensors, air bag modules, steering column and instrument panel, disable the SRS, as described earlier in this section.
  3. Remove the right instrument panel side trim.
  4. Remove the two retaining screws at the lower right side support beam.
  5. Remove the instrument panel support bolt at the A-pillar.
  6. Remove the left instrument panel side trim and upper instrument panel bezel.
  7. Remove the lower knee bolster and console screws at the instrument panel.
  8. Remove the gearshift knob and shifter bezel.
  9. Remove the mounting screws at the front and rear of the floor console. Remove the front and rear console halves.
  10. Remove the right side instrument panel support strut.
  11. Drain the cooling system into a suitable container, then disconnect the heater hoses at the cowl panel. Plug the heater core outlets to prevent coolant from spilling during unit housing removal. Fig. 1: Remove the heater core cover 90906g01.gif
    Fig. 2: Remove the heater core 90906g02.gif

  12. Remove the mounting screws and heater core cover.
  13. Remove the heater core from the vehicle. To install:
  14. Carefully position the heater core unit into the heater housing.
  15. Install the heater core cover onto the heater housing and tighten the mounting screws.
  16. Install the right side instrument panel support strut.
  17. Install the front and rear console halves.
  18. Install the shifter bezel and gearshift knob.
  19. Install the lower knee bolster and console screws at the instrument panel.
  20. Install the upper instrument panel bezel and left instrument panel side trim.
  21. Install the instrument panel support bolt at the A-pillar.
  22. Install the two retaining screws at the lower right side support beam.
  23. Install the right instrument panel side trim.
  24. Install the radio/HVAC control module bezel.
  25. Fill the cooling system to the proper level.
  26. Connect the negative battery cable.
Sebring Coupe and Avenger
  1. Disconnect the negative battery cable. CAUTION
    The vehicles covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses air bags. Whenever working near any of the SRS components, such as the impact sensors, air bag modules, steering column and instrument panel, disable the SRS, as described earlier in this section.
  2. Remove the instrument panel from the vehicle, as outlined in Section 10 of this manual.
  3. Drain the cooling system into a suitable container, then disconnect the heater hoses from the dashboard panel. Plug the heater core outlets to prevent coolant from spilling during unit housing removal.
  4. Remove the center stay.
  5. Remove the lap cooler duct mounting screw. Remove the center duct.
  6. Remove the left and right rear heater ducts.
  7. Remove the foot distribution duct.
  8. If equipped with A/C, remove the cooling unit mounting nut and bolt.
  9. Remove the retainer clip, then the heater unit.
  10. Remove the heater core. Fig. 3: Exploded view of heater unit and core assembly 90906g03.gif
    To install:
  11. Install the heater core into the heater housing.
  12. Install the heater housing and retainer clip into the vehicle.
  13. If equipped with A/C, install the cooling unit mounting bolt and nut.
  14. Install the foot distribution duct. Install the left and right rear heater ducts.
  15. Install the center duct, then install the lap cooler duct mounting screw.
  16. Install the center stay and connect the heater hoses to the heater core at the dashboard panel.
  17. Install the instrument panel.
  18. Fill the cooling system to the proper level.
  19. Connect the negative battery cable.

Jul 08, 2010 | 1997 Dodge Stratus

1 Answer

Need to replace heater core on 96 tbird....I have Instrument panel out.....glove box out.....center console (climate control unit and stereo) out......have heater hoses disconnected and two mounting nuts...




Section 12-03A: Air Conditioning System—Manual A/C-Heater 1996 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION Heater Core Removal
  1. Partially drain the cooling system.
  1. Remove the tube gasket from the heater core tubes.
  1. Remove four heater core access cover retaining screws, and remove the access cover from the A/C evaporator housing (19850).
  1. Remove A/C electronic door actuator.
  1. Slide heater core (18476) and seals from the A/C evaporator housing (19850).
Installation
  1. Install the heater core (18476) in the A/C evaporator housing (19850) with the tube gasket on the outside of the case.
  1. Install the A/C electronic door actuator as described.
  1. Position the heater core cover on the A/C evaporator housing (19850). Install the four retaining screws.
  1. Refill the cooling system.


    Heater Core





    Item Part Number Description 1 18596 Heater Core Tube Gasket 2 18476 Heater Core 3 18B300 Heater Core Cover 4 390747-S2 Screw (4 Req'd) 5 18N267 Heater Core Cover Seal
  2. 3e541cd.gif

      Feb 16, 2010 | 1996 Ford Thunderbird LX

      1 Answer

      Have a 2006 Honda Odyssey Touring - tail lights went out but brake lights and turn signals both work. Dealer said there is no fuse for the tail lights (owners manual listing of fuses does not show any for...


      dealer is and ***, there will be a fuse somewhere for that area, what else does not work, normally each sidelight is a separate curcuit, front and rear on each side on same curcuit, hence would guess bad earth curcuit in the unit. email honda and report dealer and ask same

      Dec 22, 2009 | Honda Odyssey Cars & Trucks

      1 Answer

      2002 Ford Expedition Eddie Bauer 5.4l Dual A/C Are there 2 orifice tubes in the split unit? Where are they located? Is there a diagram available showing the tubes in the system?


      There is one orifice tube for the font air. It is located in the a/c line coming from the condenser to the evap. core. the rear a/c has and expansion valve attached to the rear evap. core. Hope this helps.

      Oct 07, 2009 | 2002 Ford Expedition

      1 Answer

      Changeing heater core in Grand Marquee 1988


      go to your nearest parts house and get you a haynes repair manual it will tell every thing you need to know

      Dec 13, 2008 | 1988 Mercury Grand Marquis

      Not finding what you are looking for?
      Cars & Trucks Logo

      Related Topics:

      40 people viewed this question

      Ask a Question

      Usually answered in minutes!

      Top Cars & Trucks Experts

      yadayada
      yadayada

      Level 3 Expert

      76673 Answers

      Colin Stickland
      Colin Stickland

      Level 3 Expert

      22219 Answers

      Randy Ohler

      Level 3 Expert

      14585 Answers

      Are you a Car and Truck Expert? Answer questions, earn points and help others

      Answer questions

      Manuals & User Guides

      Loading...