Question about 2004 Cadillac Escalade Esv

Open Question

FUSE FOR REAR WIPER - 2004 Cadillac Escalade Esv

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rear wiper fuse located for a 2004 BMW X5


F81 20 Amp Rear wiper and washer fuse located in Rear cargo compartment panel on right side.

Also check F41 5 Amp Rear wiper control module fuse location above glove box

Dec 24, 2016 | BMW X5 Series Cars & Trucks

1 Answer

Rear wiper doesn't work


check rear wiper fuse and relay.if wiper motor getting power but do not work.rear wiper motor bad.if fuse and relay okay but no power going to rear wiper rear wiper switch could be bad.

May 14, 2013 | 2000 Seat Ibiza

2 Answers

Back windshield wiper won't turn on


The rear wiper has a dedicated fuse. It's the 10A R/WIPER fuse in the relay block. This supplies power to the rear wiper and washer switch and the rear wiper control unit. That unit also gets power from the 20A AUDIO (!) fuse in the engine room fuse box. If the fuses are OK, the ignition switch is in the ON position, and the rear wiper and washer switch is turned on the rear wiper should work. If not check all the components described to find where the loss of power is occurring

Nov 15, 2012 | 2005 Kia Sorento

1 Answer

Rear window wiper not working in 97 hyundai coupe


Remove the rear hatch door inner skin and check for power there.
If you have power, then the rear wiper motor has failed.
If no power, then check the rear wiper switch for power and operation.

Nov 12, 2012 | Cars & Trucks

1 Answer

Ford Expidition 2001, rear wiper is not working, water sprays but no action


The washer and wiper are two separate circuits. At the central junction box check 15A fuse 14 which feeds the battery saver relay. At the battery junction box, check fuse 12 which feeds the rear wiper down and up relays. Rear wiper action is controlled by the generic electronic module (GEM). If the rear wiper switch is set to one of the intermittent positions, the battery saver relay closes to apply power to the wiper down and up relays. The GEM selects high/low or park operation. Note that there is an internal thermal breaker in the rear wiper motor so if everything else checks out, the motor may have overheated and opened that fuse. also, the rear wiper relay(s) could be defective

Sep 28, 2012 | 2001 Ford Expedition

2 Answers

Air bag light is on 96 grand caravan


i may be mistaken on if this applies to your model year but if the rear wiper does not work then check the fuse for rear wiper and replace if blown. make sure rear wiper switch is off and wiper is parked.if air bag light goes out after a few seconds then the rear wiper motor is bad causing fuse to blow. air bag module gets power for its fuse through wiper fuse.if wiper is not parked then fuse may blow when you turn yhe key on.you have two choices. replace wiper motor or remove tailgate door panel and unplug the motor

Apr 04, 2010 | 1996 Dodge Caravan

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

2 Answers

Fuse for rear wiper blade 1995 ford windstar van gl


The rear wiper fuse number is 24 in the passenger compartment fuse box.

Nov 04, 2008 | 1995 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...