Question about 1992 Toyota Pickup

1 Answer

Thanks to every one that sent suggestions. Here

Thanks to every one that sent suggestions. Here is the problem I can start and drive my truck no problems. However after 7-8 miles it starts to stall then the Am2 fuse blows. I have checked out all of the wire connections that are visible and I have replaced plug and wires distubutor cap ignition module and coil. This has not changed anything.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

You need to verify where is the voltage line of AM2, you may have a problem of the wire shorting out on the ground when your car on full speed after 7 to 8 miles.

Posted on Oct 15, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: diagram for replacing distributor, cap, rotor...

Replace the coil. It is shorted out. I have changed quite a few coils for the exact same symptom.

The graciousness of a FixYa rating for my assistance would be appreciated.

Thanks for choosing FixYa for assistance.

Posted on Jan 21, 2009

nvannoy
  • 234 Answers

SOURCE: 1993 toyota corolla, problem no spark to spark

Check the ignition relay and all the main relays on the battery.

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes all the warning lights to come on? Car won't start. No info sent to error data port.


No info sent to error data port. ? That is the DLC - data link connector ! Pin 16 in that connector should have battery + voltage ,to power up a scan tool . This is very complex , suggest you take your vehicle to the dealer or a ASE certified repair shop . There could be a short in the serial data communication network or a module on the data bus .

OBD II diagnostic interface pinout

Feb 23, 2016 | 2009 Lincoln MKZ

1 Answer

My car cut out and will not start again


What car? And what was the weather on the drive

Jul 13, 2017 | Cars & Trucks

1 Answer

Truck not idling and cutting off


Now clean MAF , install new TPS , Clean injectors .

Jan 23, 2013 | 1991 Chevrolet C1500

1 Answer

Truck starts low idle about 500rpm, sputters then


have some one check the mass air flow sensor or idle air control

Mar 02, 2010 | 1999 Chevrolet K1500

1 Answer

In my 1991 F150 (186,000 imles)I have a strong glychol smell that is comming from my HVAC system - the only thing I can think of is a leak in the heater core, but I nothing dripping to the ground. Could...


Your nose and suspicions are probably correct. If you start to notice a film on the inside of your windshield while driving at night its definately your heater core pushing antifreeze through your defrost vents. I don't suggest trying any additives. Those quick fixes have sent more vehicles to the junk yard than I'd like to think about.

Feb 20, 2010 | 1991 Ford F150

1 Answer

My 2006 GMC Envoy Denali is stuck in 4 wheel drive low. I tried putting it in reverse and then drive but to no avail. Any other suggestions? Also...can I still drive it until I can get to the...


i would not suggest driving it u can start by replacing the selector switch as this is the cheapest thing to replace my switch was bad and made mine stay in four low please rate my advice

Dec 20, 2008 | 2006 GMC Envoy Denali

1 Answer

Engine swap lookin for a 5.9 computer #


If you told a good dealer parts person what you where trying to do they could get the correct calibration processor for you, you are dealing with a bunch of by the book parts people, can't think outside the box.

Oct 10, 2008 | 1990 Dodge Ram

1 Answer

Dashboard Light off


you have to reprograme engine control computer in your car

Jul 13, 2008 | 2004 Honda Accord

Not finding what you are looking for?
1992 Toyota Pickup Logo

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...