Question about 2001 Dodge Neon

2 Answers

Seems to be missing when put in gear worse when put in reverse when gas is pressed goes away .has not thrown any codes

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 88 Answers

Plugs and wires ! when I get a car that misses I found it is usually the wires causing the issue. always best to replace them at the same time as one will cause the other to fail.

Posted on Mar 15, 2014

  • _-__-___-_
    _-__-___-_ Mar 15, 2014

    150 day old post.


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 20,706 Answers

Misfire is P030x DTC codes.
but only trip when much worse ,
no matter, your seat of pants are smarter than any ECU on earth.
no lie.
ever give it a tune, up ,if not why not?
misfire hot or cold block. or both?
sure under load,
the car has a 60k mile service schedule , ever consider doing that? this stops 90% of all misfires.

Misfire can be , (bad 12vdc electrical power to EFI components)

1: lost compression hot. or cold. or both.
2: bad spark, (tuneup skipped, easy peasy, do it)
3: bad fueling. (vast reasons, but air leaks, bad 02 sensor, bad air meter if opted, low fuel pressure or insane high at 60psi not 30.
never changed the fuel or air filter, yes, that tune up list calls.
just to name a few.

it can also be caused by leaking EGR main valve.
it too is a 50k service point, (clean it)

Posted on Oct 15, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

1991 GMC Jimmy has vibration at around 50 MPH.

get your tires checked definitly sounds like a balance problem could be a bent rim also

Apr 06, 2015 | 1991 GMC S-15 Jimmy

1 Answer

Bogging down at stop lights, dyin in reverce

Sound like a vacuum leak to me, check all vacuum lines to see if they are all connected and have no splits or damage.

Apr 15, 2014 | 1991 Toyota Celica

1 Answer

Can put into gear when running but when i release clutch and give gas truck dont move but i haer a low clunk sound, could it be my pressure plate or gears in my transmission?

if you can put it into gear release the clutch , no movement its more than likely the clutch assembly broken spring in the pressure plate , have you tried all gears also reverse if it goes into all gears no movement or if the sound get worse or goes away in different gear then I would say input shaft bearing , my bet is clutch assembly

Jan 04, 2014 | 1988 Ford Bronco

2 Answers

Engine code po456 on a 2005 mustang gt

It's a code related to an EVAP leak in your emissions system. A lot of people have reported loosening their gas cap, re-tightening it, and then clearing the code with success in it not coming back. Here is a bulletin posted on the issue from ALLDATA

Jul 28, 2012 | Ford Mustang Cars & Trucks

1 Answer

I have T5 2.5 turbo Drive for about 5 minutesthen it starts to judder between 1500 to 1800 rpm gets worse on light throtle .put foot on throttle or back off and judder goes away then ASR light comes on...

you may have a bad turbo it is common on the vw. with engine off take off big black tube and see if filled up with oil. if has alot of oil it in it will need to be replaced.
did the cam code come back on or was this a old code stored in memory?

Jan 06, 2012 | Volkswagen Transporter Cars & Trucks

1 Answer

I have a 2005 F150 XLT, when I put in reverse it seems to take a little to long to engage, then when it does the truck shatters for the first few feet in reverse. Also, if I put it in reverse then hit the...

Might want to check the trans fluid for level and cleanliness. This would be my 1st thought, even though the OM has something like a 100K service interval.

May 04, 2011 | 2005 Ford F-150

Not finding what you are looking for?
2001 Dodge Neon Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides