Question about 2007 Jeep Compass Limited

1 Answer

How to bleed clutch 2007 compass - 2007 Jeep Compass Limited

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 95 Answers

GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

2. Raise vehicle on hoist.

3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

8. From driver's seat, actuate clutch pedal 60-100 times.

9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

6. Turn on the service filling machine.

7. Crack open the bleeder valve (3).

8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

10. Close the bleeder valve and disconnect the service filling machine.

11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

12. Check clutch pedal to see if vehicle is properly bled.

13. If vehicle is not properly bled, repeat procedure.

14. Remove bleeder cap from reservoir and replace reservoir cap.

15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

Posted on Oct 15, 2013

  • 2 more comments 
  • tomas sidlauskas
    tomas sidlauskas Oct 15, 2013

    GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

    2. Raise vehicle on hoist.

    3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

    4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

    5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

    6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

    7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

    8. From driver's seat, actuate clutch pedal 60-100 times.

    9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

    10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

    POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

    2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

    3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

    4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

    5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

    NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

    6. Turn on the service filling machine.

    7. Crack open the bleeder valve (3).

    8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

    9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

    10. Close the bleeder valve and disconnect the service filling machine.

    11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

    12. Check clutch pedal to see if vehicle is properly bled.

    13. If vehicle is not properly bled, repeat procedure.

    14. Remove bleeder cap from reservoir and replace reservoir cap.

    15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

  • tomas sidlauskas
    tomas sidlauskas Oct 15, 2013

    GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

    2. Raise vehicle on hoist.

    3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

    4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

    5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

    6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

    7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

    8. From driver's seat, actuate clutch pedal 60-100 times.

    9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

    10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

    POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

    2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

    3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

    4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

    5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

    NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

    6. Turn on the service filling machine.

    7. Crack open the bleeder valve (3).

    8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

    9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

    10. Close the bleeder valve and disconnect the service filling machine.

    11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

    12. Check clutch pedal to see if vehicle is properly bled.

    13. If vehicle is not properly bled, repeat procedure.

    14. Remove bleeder cap from reservoir and replace reservoir cap.

    15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

  • tomas sidlauskas
    tomas sidlauskas Oct 15, 2013

    GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

    2. Raise vehicle on hoist.

    3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

    4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

    5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

    6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

    7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

    8. From driver's seat, actuate clutch pedal 60-100 times.

    9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

    10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

    POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

    2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

    3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

    4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

    5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

    NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

    6. Turn on the service filling machine.

    7. Crack open the bleeder valve (3).

    8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

    9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

    10. Close the bleeder valve and disconnect the service filling machine.

    11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

    12. Check clutch pedal to see if vehicle is properly bled.

    13. If vehicle is not properly bled, repeat procedure.

    14. Remove bleeder cap from reservoir and replace reservoir cap.

    15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

  • tomas sidlauskas
    tomas sidlauskas Oct 15, 2013

    GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

    2. Raise vehicle on hoist.

    3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

    4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

    5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

    6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

    7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

    8. From driver's seat, actuate clutch pedal 60-100 times.

    9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

    10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

    POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

    1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

    2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

    3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

    4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

    5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

    NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

    6. Turn on the service filling machine.

    7. Crack open the bleeder valve (3).

    8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

    9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

    10. Close the bleeder valve and disconnect the service filling machine.

    11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

    12. Check clutch pedal to see if vehicle is properly bled.

    13. If vehicle is not properly bled, repeat procedure.

    14. Remove bleeder cap from reservoir and replace reservoir cap.

    15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding slave cylender and clutch


Go to the link and read about the problem and the way to bleed it. How to Bleed Clutch BlueDevil Products

Sep 28, 2016 | 2007 Kia Sportage 2.0

1 Answer

How to bleed clutch cylinder for Nissan Sandra 2010


bleed clutch cylinder Robinny, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Bleeding clutch
Clutch bleed how to
Nissan Altima 2007 2012 Service Manual Clutch fluid On vehicle maintenance...
Help clutch bleeding Fail

Jul 19, 2016 | Nissan Cars & Trucks

1 Answer

How too do the bleeding of power steering pump on 2007 Jeep compass?


Bleeding a power steering pump in general is just by moving the steering wheel from end stop to end stop. Do not keep it at the end stop for a prolonged time, because it will put a lot of stress on the pump and lines. Keep an eye on the power fluid level, because when air comes out, the level will drop.

Sep 20, 2014 | Jeep Compass Cars & Trucks

1 Answer

DISASSEMBLE AC COMPRESSOR CLUTCH


07 jeep compass 2.4L, USA car, ?
diffr ,countries and diffr assemble plants use diffr, A/C systems.


FSM words, USA
5SE12 A/C compressor,
or
6SEU16 A/C compressor
Santech? is it?
the compressor has a plate on the side, read it, it has a name
and pn. then google for that or use youtube.

http://www.autozone.com/autozone/accessories/Santech-Compressor-clutch-tool-set/_/N-255s?itemIdentifier=952175_0_0_

i think the hub is threaded on to shaft tip.
some types:
One is for a MINI YORK CMPR, YORK OR TECUMSEH compressor and one is for a SANDEN/SANKYO compressor.


some need a puller
others, need that and a holder to keep it still
do not mix up or lose any spacers inside.
a newbearing is easy to find and replace. on car.
most cars.

Feb 15, 2014 | 2007 Jeep Compass 2.4

1 Answer

Won't start but cranks


Verify no pressure in the fuel rail. There is a bleed valve looks like a tire valve. (caution, a lot of high pressure fuel may squirt out)
If it does, check the Crankshaft sensor by turning the engine and seeing if the tach moves. If not I would change that first, and make sure it didn't drop a timing belt if equipped. Lastly, ECM could be bad.

Nov 13, 2013 | 2007 Jeep Compass 2.4

1 Answer

Overheating


Did you bleed the air out of the cooling system?

Apr 26, 2012 | 2007 Jeep Compass 2.4

1 Answer

2007 Jeep Compass - Clutch pedal went to the floor on my daughter --fluid is low -no visable external leaks - clutch does not slip Do I need to split the flywheel housing in order to change the slave...


Usually if you pump the pedal a lot when it's cold if the slave is leaking you will see some dripping from the bellhousing. I would definitely check inside the cab where the master attaches to the pedal rod to be sure it isn't leaking there and that's why you don't see fluid outside though. If you already checked there then yes if the slave is leaking, that's the only way in there.

Oct 03, 2010 | 2007 Jeep Compass Limited

2 Answers

2007 jeep compass. compass will start, but will


check manual shift valve linkage adjustment .some thing loose or a missing.

Jun 30, 2009 | 2007 Jeep Compass Limited

Not finding what you are looking for?
2007 Jeep Compass Limited Logo

913 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...