Question about Toyota MR2

1 Answer

Camshaftt sensor location

Removal

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,420 Answers

Need the Year and engine size please?

Leon

Posted on Oct 15, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 3.0L Escape. Where are the knock sensors located?


Knock Sensor

Print
Operation

The Knock Sensor (KS) is a tuned accelerometer on the engine which converts engine vibration to an electrical signal. The PCM uses this signal to determine the presence of engine knock and to retard spark timing.
Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the intake manifold.
  3. Remove the bolt and the Knock Sensor (KS).
  4. To install, reverse the removal procedure and tighten mounting bolt to 15ft. lbs. (20 Nm).

Jul 21, 2015 | Ford Cars & Trucks

1 Answer

I need to replace the map sensor in a 2.4 alero but I do nor know where it located.


Here is a diagram of where the map sensor is located on this particular vehicle, i have also included the removal and installation procedures as well

Hope this helps....

REMOVAL PROCEDURE

  1. Remove the air cleaner outlet resonator.
  2. Disconnect the manifold absolute pressure (MAP) sensor.
  3. Remove the MAP sensor attaching screws (1).
  4. Remove the MAP sensor vacuum hose (2).
INSTALLATION PROCEDURE

  1. Connect the vacuum hose (2).
NOTE: Refer to Fastener Notice in Service Precautions.

  1. Install the MAP sensor attaching screw (1).
Tighten
Tighten the screw to 6.5 N.m (5.7 lb in) .

  1. Connect the MAP sensor connector.
  2. Reinstall the air cleaner outlet resonator.


asetech74_0.gifasetech74_1.gif

Sep 15, 2011 | 2000 Oldsmobile Alero

1 Answer

Where is the ckp sensor located on a 2003 ford f350 6.0 diesel?


Removal and Installation
  1. Disconnect the LH and RH negative battery cables. For additional information, refer to Section 414-01.
  1. NOTE: The crankshaft position (CKP) sensor is located underneath the air conditioning compressor.
    Remove the nut and position the positive battery cable and bracket aside.
    a0068391.jpg
  1. Remove the bolt and position the battery negative cable aside.
    a0068392.jpg
  1. Disconnect the CKP sensor electrical connector.
    a0065610.jpg
  1. Remove the bolt and the CKP sensor.
    a0065611.jpg
  1. NOTE: Apply clean engine oil to the O-ring before installation.
    To install, reverse the removal procedure.

Aug 29, 2011 | 2004 Ford F350

1 Answer

How to replace crank shaft position sensor


Click over image for zoom...

zjlimited_1122.jpg

Fig. 1: View of the crankshaft position sensor and its location-1996 5.2L engine shown


zjlimited_1123.jpg

Fig. 2: View of the crankshaft position sensor and its location-1996 4.0L engine shown


Removal & Installation
4.0L Engine
  1. The CKP sensor is located on the transmission bellhousing. Disengage the sensor wiring connector and remove the sensor wiring hold-down clip from the fuel rail.
  2. Remove the sensor mounting bolt and carefully pull the sensor out of the bellhousing.
  3. Installation is the reverse of removal.

5.2L and 5.9L Engine
  1. The CKP sensor is bolted to the top of the cylinder block near the rear of the right cylinder head. Disengage the sensor wiring connector and remove the two sensor mounting bolts.
  2. Carefully pull the sensor out of the cylinder block.
  3. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

Apr 28, 2011 | 1996 Jeep Grand Cherokee

2 Answers

Replacing the MAP sensor??


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Locate the MAP sensor and remove the retaining screws
  3. Detach the electrical connector.
99e56ea.jpg

Fig. On the 3.1L engine, the MAP sensor is located alongside the intake manifold

06cd371.jpg

Fig. MAP sensor and its bracket arrangement-3.4L (VIN E) engine

c92a20a.jpg

Fig. Location of the MAP sensor on the throttle body adapter-3.4L (VIN X) Engine

ef21261.jpg

Fig. The MAP sensor is located just behind the throttle body mounting base-3.5L (VIN H) engine

c7cd8f9.jpg

Fig. MAP sensor and its location alongside the supercharger-3.8L (VIN 1) Engine

98ee1cd.jpg

Fig. On the 3.8L (VIN K) engine, the MAP sensor is located on top of the PCV valve cover
  1. Remove the vacuum hose and lift the MAP sensor from the engine.
  2. Installation is reverse of the removal procedure.

Hope helps (remember rated and comment this).

Aug 06, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Were is the crankshaft position sensor located on a 2003 dodge dakota with a 4.7l engin


ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Jun 29, 2010 | 2003 Dodge Dakota Club Cab

2 Answers

Where is crank sensor located


v6 's is by the frot crank shaft area & 4 cyl engines are on the blocks mid way lower area near the oil pan

Jan 14, 2010 | 1998 Toyota Avalon

2 Answers

2001 passat reading code p0011 what is this code. car will not start.


hI CODE 0011 IS CAMSHAFTT POSITION TIMING OVER ADVAVCED OR SYSTEM PERFORMANCE (BANK 1)

Jun 07, 2009 | 2001 Volkswagen Passat

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC


SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
4544c22.gif
#56 is the cam sensor. please rate as fixed if this is what you need.

231ee68.gif

May 02, 2009 | Ford Escape Cars & Trucks

1 Answer

Where's my O2 sensor located


Heated Oxygen Sensor (HO2S) SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Oxygen Sensor Wrench T94L-9472-A
Removal and Installation
NOTE: If excessive force is needed to remove heated oxygen sensor (HO2S) (9F472) , lubricate heated oxygen sensor with penetrating oil prior to removal.
  1. Disconnect battery ground cable (14301) .
  1. Disconnect heated oxygen sensors from engine control sensor wiring (12A581) .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove heated oxygen sensors from dual converter Y pipe (5F250) using Oxygen Sensor Wrench T94L-9472-A.
  1. To install, reverse Removal procedure. Tighten heated oxygen sensors to 36-46 Nm (26-34 lb-ft).

980db4e.gif

Feb 22, 2009 | 1994 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...