Question about Ford F150
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
po301 thru po306 all misfire codes cylinder 1-6 remove plugs and replace them..... set the plug gap first
i suggest u replace the wires also if they never been replaced all these misfire codes can set the others and one is for the oxygen sensor ( 02s or HO2S) CIRCUT MALFUNCTION do u know how to check wireing systems
do the tune up plugs (set gap) .052-.056 change the fuel filter also. clear the codes hows it run
this info is for 98 E-250 4.2Litre
what engine do u have 4.2L or 4.6L i know it is a v-6 by the codes
Posted on Dec 15, 2008
Your auto has four O2 sensors. Two upstream and two downstream; With two banks. Bank 1, sensor 1...and bank 2, sensor 1 are the two upstream (exhaust manifold before the catalytic). Bank 1, sensor 2 and bank 2, sensor 2 (other side of catalytic)
Code 1131= upstream; bank 1..sensor 1
Code 1151= upstream; bank 2..sensor 1
Code P0136 (generic code) bank 1..sensor 2 (questionable)
I wouldn't spend the money to purchase 3 sensors. Highly unlikely all three are bad; Cost is about $40/ ea.
Since there isn't a code for the cat's themselves, I would suspect the O2 circuit is malfunctioning. The rough idle is another clue.
Take an ohmmeter set it on X10 scale and measure the resistance from engine to body and body to negative post on battery terminal. You should read zero ohms (full needle deflection). If you do go buy two upstream O2 sensors. If you read
open or a high resistance run two straps from eng. to body...and body to neg.batt. post.
Posted on Dec 10, 2009
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.
Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.
Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.
PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt
Posted on Jan 13, 2010
P1131 DTC P1151 indicates the system is correcting RICH for an overly LEAN
condition. The Heated Oxygen Sensor (HO2S) voltage is less than 0.45
volts. This is usually due to a vacuum leak after the MAF. It can also
be caused by a bad PCV valve or PCV system hose.
It can also be caused by low fuel pressure or a plugged injector.
Start with the simple and clean the MAF and the IAT sensor. In simple terms, the engine is running lean and is being compensated by the ECM. P1131 is bank 1 and P1151 is bank2
Good luck and keep me posted.
Posted on Feb 17, 2010
If both, P1131 and P1151 trouble codes are set at the same time, the problem will most likely be attributed to a vacuum leak past the MAF (Mass Air Flow) sensor or something else that would likely affect BOTH banks. If the problem is only causing one code or the other, but NOT both, the problem will most likely be something that would affect one bank, like a bad O-2 sensor or a fuel injector; the most common cause of a single code either the P1131 or P1151 in my experience has been a bad Oxygen sensor.
Posted on Feb 17, 2010
Tips for a great answer:
Oct 22, 2013 | Ford Mustang Cars & Trucks
May 17, 2011 | Ford Crown Victoria Cars & Trucks
Mar 12, 2011 | Ford F-150 Cars & Trucks
Jan 19, 2011 | 2000 Lincoln Town Car
Feb 17, 2010 | 2001 Ford F150 Styleside SuperCrew
Jan 13, 2010 | 2003 Ford F150 Regular Cab
Nov 07, 2009 | 2001 Mazda Tribute
Oct 14, 2009 | 2000 Ford Windstar
Oct 16, 2008 | 1996 Ford Taurus
149 people viewed this question
Usually answered in minutes!