Question about 1995 Jeep Wrangler

Open Question

How to remove blower motor on a 1995 jeep wrangler, is their a cover on the engine compartment that has to be removed

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: 4wd problem jeep wrangler yj 1995

i just bought a used 97 CHEROKEE but i had the same problem, when i got to looking at it i found out the front driveshaft was shot, look at that, if its not it i would say its probably the transfer case especially with an older vehicle like that which is a very expenxive repair

Posted on Dec 21, 2008

  • 6982 Answers

SOURCE: 1988 Wrangler Ignition Switch Removal

There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Posted on Jan 05, 2009

c17hydro
  • 2984 Answers

SOURCE: 2003 oil pan removal

4.0L Engine To Remove:

  1. Disconnect negative battery cable.
  2. Lift the vehicle.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Exhaust pipe from exhaust manifold.
    • Exhaust hanger at the catalytic converter and lower the pipe.
    • Starter motor.
    • Flywheel/torque converter housing access cover.
    • Oil level sensor (if equipped).
  5. Place a pole jack under vibration dampener with a piece of wood between dampener and jack.
  6. Remove or disconnect the following:
    • Engine mount through bolts and raise engine for clearance to remove pan.
    • Transmission cooler lines (if equipped).
    • Oxygen sensor harness from oil pan mounting studs.
    • Oil pan bolts and studs.
    • Oil pan and gasket.
To Install:
  1. Clean the gasket mating surfaces.
  2. Apply Mopar® Silicone Adhesive Sealant or equivalent onto the cylinder block in four location as shown.
7605306.gif

  1. Attach the pan gasket to the oil pan with Hi-tack or equivalent (2003-2005 vheicles).
  2. Use 1 ½ x ¼ inch bolts to fabricate alignment dowels. Cut off the head of the bolts and cut a slot into the top of the dowels (2006 vehicles).
4e495fd.gif

  1. Install two dowels into the timing case cover (2006 vehicles).
  2. Install two dowels into the cylinder block (2006 vehicles).
  3. Place the gasket over the dowels and onto the cylinder block and timing case cover (2006 vehicles).
  4. Position the oil pan.
  5. Install the 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm).
  6. Install the 5/16 inch oil pan bolts. Tighten to 132 in-lb (15 Nm).
  7. Remove the dowels.
  8. Install the remaining 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm) (2006 vehicles).
  9. Lower the engine onto the engine mounts.
  10. Install the through bolts and tighten the nuts.
  11. Remove jack stand and remove the piece of wood.
  12. Install the flywheel and torque converter access cover.
  13. Install starter motor.
  14. Connect the exhaust pipe to the hanger and to exhaust manifold.
  15. Install the transmission oil cooling lines (if equipped).
  16. Install the oxygen sensor wiring supports to the oil pan mounting studs.
  17. Install the drain plug into the oil pan. Tighten to 25 ft-lb (34 Nm).
  18. Lower the vehicle.
  19. Connect negative battery cable.
  20. Fill the oil pan with oil. WARNING
    Use extreme caution when the engine is operating. Do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
  21. Start the engine and inspect for leaks.

Posted on Jun 06, 2009

  • 12 Answers

SOURCE: Removing doors from Jeep Wrangler - Dome Light Stays On

I have a 97, and my fuse for that is behind the glovebox. Open the box, slide the end of the strap to disconnect it, then remove the box. The fuse is marked. Something like "Dome lt. elim." I think it's located one up from the bottom right. This can actually be done without removing the glove box. For a more permanent fix, quadratec.com has a switch that plugs into the fuse location and mounts under the dash, so you can just flip the switch. Hope this helps.

Posted on Jul 14, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2002 Jeep Wrangler blower motor is not working on

If fuse is good, then turn switch on, and take a voltmeter or test light and test power to the motor. If there is power, then motor is bad. If no power, than switch or relay is bad.

Posted on Nov 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change heater core on 1988 jeep wrangler


old car. with A/C or with out. we cant guess this..
log in to alldata. com and read?
  1. drain coolant,
  2. remove housing
  3. remove core. (easy but what is step 2)

housing. no A/C
step 2. expanded.
  1. Disconnect the heater hoses at the engine side of the firewall.
  2. Detach the heater control cables.
  3. Disconnect the motor wiring.
  4. Detach the water drain hose and the defroster hose.
  5. Remove the nuts from the studs in the engine compartment.
  6. Tilt the heater housing assembly down and pull it back toward the inside of the vehicle.
  7. Remove the attaching screws and the blower motor.

alldata.com covers this , with nice photos. why not just login and read.

Oct 01, 2014 | 1988 Jeep Wrangler

1 Answer

Both headlights out on 1997 Jeep Wrangler. Don't see a fuse in the box in the dashboard indicating headlamps. Looked in the engine compartment, but don't know which fuse to check.


There is a fuse box under the hood on the passenger side remove the cover and the #10 fuse is for the headlamps. Look on under side of cover for fuse #s.

May 19, 2011 | 1997 Jeep Wrangler

1 Answer

Do i have to pull the dash back and remove the case to replace blower motor my truck has a/c


no, you remove the blower motor from under the hood.

Disconnect negative battery cable. Disconnect blower motor harness connector in engine compartment, near blower motor. Remove blower motor screws. rotate and tilt blower motor assembly as needed for clearance, remove blower motor. To install, reverse removal procedure.

Jan 28, 2011 | 2001 Jeep Cherokee

1 Answer

Replace the heater blower motor resistor in 2000 Jeep Wrangler Sport. Having trouble finding the resistor...do I take off more than the glove compartment door / box?


if its in the way yes...But the resistor is usually mounted within the blower motor box. Wires powering up the blower motor is coming from the resistor. Follow those lines!!

Dec 13, 2010 | 2000 Jeep Wrangler

2 Answers

Where is the heater fan located to fix it??


The blower motor is mounted in the engine compartment, behind the wiper linkage on this model

70d2c49.gif

OR

Interior Mounted
  1. Remove the right-side instrument panel insulator.
  2. Disconnect the blower motor cooling hose.
  3. Detach the blower motor electrical connector.
  4. Remove the blower motor-to-air housing mounting screws.
  5. Pull the blower motor out of the air housing.

Nov 13, 2009 | 1995 Pontiac Trans Sport

1 Answer

How do you replace a heater motor on a 1995 jeep wrangler


you will need to remove the heater housing(air box) . the blower is mounted in it. start by removing the control cables (slide your heater controls and you will see them move under the dash),they just snap in place.be careful not to break the plastic tabs. unhook the defroster tube(looks like a corrugated paper pipe in the center and on the top of the housing). unplug the wire harness in the upper corner of the passenger side. now under the hood remove both heater hoses. then remove the four mounting nuts on the firewall [they are 7/16] . one nut is on right side of the battery.one just left of the battery. one is under the battery toward the bottom of the firewall.the 4th is by the left rear corner of the valve cover. there may be an accelerator cable loom snapped over this stud,it just pries off. lay a towel or rags on passenger floor to catch any anti freeze. with all 4 nuts now removed,pull the housing away from the firewall.you may have to tilt the bottom out slightly. once the housing is removed take it to your work bench. you will see about 6 hex head screws holding the blower in place, remove these. pull out blower. fairly simple,but the nut under the battery can be a pain to get to.

Nov 02, 2009 | 1995 Jeep Wrangler

1 Answer

Location off the blower resistor.


The blower motor is located in the engine compartment on the right side of the firewall.


  1. Disconnect the negative battery cable from the battery.
  2. Disconnect the electrical connectors from the blower motor.
  3. Remove the radiator coolant collecting bottle from the right side of the engine compartment.
  4. Remove the windshield washer fluid bottle from the right side of the engine compartment.
  5. If equipped with an acoustic cover over the motor, cut the cover between the clip lands and save the cover for reassembly.
  6. Remove the blower motor-to-duct housing screws and the blower motor from the vehicle.
  7. If necessary, replace the blower motor-to-duct housing gasket.
  8. Installation is the reverse of the removal procedure. Tighten the retaining screws to 18 inch lbs. (1.6 Nm).

Oct 27, 2009 | GMC Safari Cars & Trucks

1 Answer

How do I change a blower motor for a 1994 jeep wrangler!! Help !


it is accessable from the passenger side just under the dash. remove the glove box to help with access, held in with four 8mm screws, remove screws and it just pulls right out.

Sep 16, 2009 | 1994 Jeep Wrangler

1 Answer

How to install heater blower


This is an easy solution. Remove the glove box door strap and remove the glove box door by letting it drop towards the floor while supporting the door and it will release from the dash. Then you will see the blower motor housing along the firewall on the interior. You will just need to unplug the wires to the motor and remove a few screws and carefully remove the motor with the blower cage attached to it. Then just reverse the process and you will be good.

Jan 11, 2009 | 1994 Jeep Wrangler

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...