Question about 2003 Ford Explorer

Open Question

Change panel vent blend door actuator on 08 mustang

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

harley9701ha
  • 424 Answers

SOURCE: cant find the blend door actuator on 2003 ford f150 super crew

The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Posted on Jun 22, 2009

SOURCE: Why, after changing the blend door actuator, does

Check all the air hose up to that point look to see if all hose is intack and put to gether right look for holes and cloges

Posted on Oct 06, 2009

roniecon
  • 6826 Answers

SOURCE: need to locate blend door actuator on 2002 ford

Open the glove box,and look on top of ac/heater box toward the center of vehicle,it should be setting right there.

Posted on Oct 10, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

bunnydawg
  • 5158 Answers

SOURCE: 2002 Ford Crown Vic 4.6L. EATCM A/C, Heating

that clicking noise you hear is likely a relay in the fuse panel that needs to be replaced. the easiest way to find out which relay it is would be to put you finger on each relay as you actuate the device not working. once you locate the clicking relay replace it . to reset the computer just unhook the battery for about ten minutes. if you have an anti theft radio make sure you know the code for it and how to enter it before you unhook the battery.

robert

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is rhe air temp. Door actuator in a 2003 ford 450 truck


Ford Superduty Erratic Temp Blend Door Actuator Removal - YouTube

? 12:29
https://www.youtube.com/watch?v=dYPOtin3JUk
Dec 1, 2013 - Uploaded by FordTechMakuloco
Only buy the Ford Actuators, you can get them cheaper here- ...

Simple how to fix blend door heater a/c actuator 2002 - 2008 ford ...

? 7:12
https://www.youtube.com/watch?v=EEWuJuhCtmc Aug 24, 2013 - Uploaded by kirk colombo
Simple how to fix blend door heater a/c actuator 2002 - 2008 ford explorer noise .... I literary just finish ...

08-10 Super Duty Blend Door Actuator Location - Dual System ...

? 1:24
https://www.youtube.com/watch?v=s7awF2fTKf4 Mar 22, 2012 - Uploaded by srmastertech
Here is a quick view showing the location of the temp blend door actuators on the Ford Super Duty's with ...

Ford blend door fix - 15 minutes - YouTube

? 3:22
https://www.youtube.com/watch?v=wsjGxreGlkA Jul 21, 2013 - Uploaded by SoonersWarriors
Ford blend door fix - 15 minutes. SoonersWarriors. Loading ... Ford Vehicles: Frequent Blend Door Actuator ...

Blend Door Actuator Ford Super Duty 08-10 - YouTube

? 9:45
https://www.youtube.com/watch?v=mbzjCPYENZQ Oct 4, 2013 - Uploaded by MostExcellentDude
This applies to 2008-2010 F250 and F350 with the dual climate control. This video shows the locations for the ...
blend door actuator 2003 ford f450 Google Search




Aug 16, 2017 | Ford Cars & Trucks

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

2 Answers

Ac is blowing out of defrosterandnot panels in the dash. Air is cool cold air will blow out of rear seat panel/vent 1998 ford explored


The most common cause is a bad blend door actuator which controls air flow throughout the cabin. When air flow only flows from 1 section (either floor, vent, or defrost) it's an indication that the blend door actuator is either stuck or broken.

Jun 02, 2011 | 1998 Ford Explorer

2 Answers

No air from the vents, the fan is running


not very good one to fix , somtimes cables that operate opening and closing of air vents bellow dash separate , and stop from opening , i think you will find most things under foot panels near passenger feet . and center consol near passenger feet . , you may need to take of those panels to see is you can visially see anything .

Nov 10, 2010 | 1992 Volvo 740

1 Answer

2 vents blow semi cold aair and the other 2 blow hot air


You have a blend door issue under dash. Also possible blend door actuator motor may have failed. Try moving the mode select dial on control panel back and forth and listen for air sound change under dash at both sets of vents. If do not hear air flow change door is not moving.

Jul 21, 2010 | 2001 Volvo S60

1 Answer

My heater will only blow hot air out of the rear vents from the rear controls. The front vents only blow cold air. Is there a simple fix?


blend door or temp contrl switch is bad.

Section 12-02: Heating and Defrosting 1998 Windstar Workshop Manual
REMOVAL AND INSTALLATION Actuator Motors, Electric Temperature Blend Door
Removal
  1. Remove cassette storage box or center shelf unit, if equipped.
  1. Remove instrument panel ash receptacle (04810) by depressing service lever.
  1. Disconnect electrical harness connector from electric blend door actuator.


    sww~us~en~file=am0101a.gif~gen~ref.gif

  1. Remove three retaining screws.


    sww~us~en~file=am0100a.gif~gen~ref.gif

  1. Carefully pull electric blend door actuator outward and off A/C evaporator housing (19850) assembly.
Installation
  1. Follow removal procedure in reverse order.
  1. Air temperature control door shaft is keyed. Move door to properly insert electronic actuator shaft. Make sure the shaft is completely in and properly seated.

Jan 14, 2010 | Ford Windstar Cars & Trucks

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

2 Answers

Need to replace ac blend door motor inside dashby glove box does dash have to come out and how much trouble is it?


the bummer is removing instrument panel. big job.

A/C Electronic Blend Door Actuator Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove instrument panel (04320). Refer to Section 01-12 .
  1. Remove four A/C electronic blend door actuator retaining screws.
  1. Remove A/C electronic blend door actuator.


2c01b1e.gif
Item Part Number Description 1 18471 Heater Air Plenum Chamber 2 42141-S8 Screw (4 Req'd) 3 — A/C Electronic Blend Door Actuator 4 — A/C Air Temperature Control Door Shaft (Part of 18471) 5 19D842 A/C Air Temperature Control Door

Feb 23, 2009 | 1997 Lincoln Town Car

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
2003 Ford Explorer Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...