Question about 1995 Jeep Cherokee

1 Answer

Crankshaft removal of a 1995 jeep cherokee 2.5td

How do i remove a crankshaft from a 2.5td jeep cherokee many thanks steve.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

To remove crankshaft, engine must be removed from vehicle. It is bolted to the flywheel/flex plate of your transmission. Even if you found a way to remove it, it would be really difficult to replace it correctly. If you are going to replace it due to a bearing failure, keep in mind that debris from that failure likely has migrated into oil galleys and is waiting there to damage new bearings. At the very least all passages should be blown out with high pressure air, preferable is to strip engine down and also check cam bearings which may also be worn from pressure loss during failure and debris.
good luck!!

Posted on Apr 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove crankshaft pullie

you will need a locking tool found on ebay

Apr 14, 2013 | 1995 Jeep Grand Cherokee

1 Answer

Step by step removal of a crank shaft positioning sensor on a 1994 jeep g. cherokee 5.2 v8

It is held to the block with one or two bolt just to the left (passenger side) of and above the crankshaft pulley, unplug the sneor taking care to not break the lock on the connector and remove the bolts and take the sensor off.

Aug 06, 2012 | 1995 Jeep Grand Cherokee

1 Answer

Hello, how to relieve the belt tension on jeep grand cherokee 1995?


In order to relieve the belt tension in your cherokee jeep,you have to locate the belt tensioner pulley first, which is found between the crankshaft and a component toward the top of the hood area.

Afterwards,Rotate the belt tensioner pulley, using a wrench spanner to relieve the tension on the belt.

Good luck.

Aug 20, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How do i change the crankshaft position sensor on a 95 jeep grand cherokee

Test it first. Remove it and replace it.(two screws)..hardest part is getting your hand up to where it is...most are at the 11o'clock position looking from the rear, (on the drivers side), on the transmission bellhousing, even with the flywheel. Harness goes up near the master cylinder.

Jun 16, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell way from top under brake booster use a wrench,

Jun 13, 2009 | 1995 Jeep Grand Cherokee

1 Answer

How to remove the ignition switch in a 1993 Jeep Cherokee?

you need to remove steering wheel and you will see how its done once you get inside

Dec 10, 2008 | 1995 Jeep Cherokee

2 Answers

Wiring diagram

Try this link

May 22, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides