Question about Hyundai Motor 2002 Sonata

Open Question

I had to replace the 95400-3d300 control module part in my 2002 Hyundai, before part went bad I was able to use my keyless remote to lock/unlock the car with the replacement part it will not lock/unlock ?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Door locks don't work

Disassemble the paneling on left side ,under the steering wheel. Remove all screws and pull out the panel until you can you can reach behind it to remove the two Black Relays, on the side closest to Steering wheel. Remove the Relay covers, Clean the contacts with a 1/8 fine strip of 600 wet/dry sand paper. Only place the paper between the contacts, and pull out while holding slight pressure on the relay Armature. Turn over the sandpaper and repeat once again. Very gently press the TOP resting contact pad closer to the armature, to lessen the gap between the contact points, so the armature doesn't have to travel as far to reach the closed contact position. Repeat the above with the other2nd Relay. Replace the covers, reinstall the relays And test the Door locks prior to buttoning up the paneling. Note, a pair of long needle nosed pliers will help in removing the relays. Just Grip the relay and rock in Forward and Backward as you apply upward pressure.

Posted on Oct 09, 2008

  • 1 Answer

SOURCE: 2003 hyundai santa fe car alarm

I had the same problem a while back. What I did was disconnect the battery for a minute and I havent had that problem since.

Posted on Feb 14, 2009

  • 37 Answers

SOURCE: Headlight bulb replacement for 2002 Hyundai

http://www.autozone.com/autozone/repairinfo/common/repairInfoMain.jsp?targetPage=productsHowToInspect&leftNavPage=productsHowTo&pageId=%090900c15280213e7e&subtitle=replace

Posted on Apr 23, 2009

ghost4548
  • 776 Answers

SOURCE: program factory remote keyless entry for 2003 Hyundai XG350

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

  • 2001 - 2004 MY Elantra
  • 2001 - 2004 MY Santa Fe
  • 2002 - 2004 MY Sonata
  • 2001 - 2004 MY XG300/350 0390020a.gif
NOTE
  • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
  • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:
  1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
  2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
    0390020c.gif
  3. Turn the Hi-Scan Pro ON
    and press ENTER
    . NOTE "Release date 29. Sep. 2003" OR LATER
    must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
    0390020d.gif
  4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
    and press ENTER
    . 0390020e.gif
  5. Select vehicle model and press ENTER
    . 0390020f.gif
  6. Select option "TRANSMITTER CODE SAVING"
    and press ENTER
    . 0390020g.gif
  7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
  8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
    0390020i.gif
  9. Press ESC
    on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
  10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.

Posted on May 31, 2009

ghost45
  • 1280 Answers

SOURCE: how to program the keyless remote for a Hyundai

You sure it's the original Keyless Remote (key fob) programmed for the vehicle? If so, you, yourself, cannot reprogram it.. you have to take the vehicle into an authorized Hyundai Dealership to have the remote programmed for the vehicle or have the problem diagnosed... sorry!

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW PROGRAM THE KEY LESS ENTRY FOR SONATA 2012


  1. Cars
  2. Car Maintenance
  3. General Car Maintenance
  4. How to Program Keyless Entry Remotes in a Hyundai Sonata
How to Program Keyless Entry Remotes in a Hyundai Sonata By Christian Killian, eHow Contributor
20Found This Helpful The keyless entry system in your Hyundai Sonata is part of the factory alarm system. If you have to replace a lost or damaged remote, reprogramming will be necessary. The remote is important because not only does it lock and unlock the doors, it also arms and disarms that factory alarm when you open or close your car doors. New remotes are available from any Hyundai dealer. While they will program it for you, you can do it yourself and save a programming fee.
How to Program Keyless Entry Remotes in a Hyundai Sonata(Kleophaus Livingston/Demand Media)

Other People Are Reading


Step 1: Locate the fuse panel under the dash on the driver's side of the car. Just below it is the control module for the factory alarm system. Open the cover on the alarm system control module and locate the memory switch inside.
(Kleophaus Livingston/Demand Media) Step 2: Verify that the switch is in the "Off" position; if it is not, switch it to the "Off" position. This is important for the system to understand what you want it to do when you move to the programming mode.
(Kleophaus Livingston/Demand Media) Sponsored Links
Step 3: Insert the key into the ignition of your Sonata and turn the key to the "On" position. Wait for 60 seconds, then move the memory switch inside the control module to "Set."
(Kleophaus Livingston/Demand Media) Step 4: Depress and hold the "Lock" button on your remote for one full minute. This allows the remote and the control module to communicate and sync. Release the "Lock" button and turn the memory switch in the control module back to the "Off" position.
(Kleophaus Livingston/Demand Media) Step 5: Turn the ignition switch to the "Off" position and test the remote by pressing the "Lock" or "Unlock" button, verifying that the doors do lock or unlock.


Read more : http://www.ehow.com/how_6362326_program-entry-remotes-hyundai-sonata.html

Mar 29, 2015 | Hyundai Sonata Cars & Trucks

1 Answer

Remote lock


your central control that control door lock may disconnected try check

Jun 17, 2013 | Hyundai Elantra Cars & Trucks

1 Answer

I need instructions to program keyless entry remote for 2002 Hundai Santa Fe


For a 1994 to 2006 Sonata, a 2001 to 2006 Elantra, a 2000 to 2006 XG350 or a 2001 to 2006 Santa Fe, you will need to access alarm system control module. On most of those vehicles it is located on the driver's side fascia panel. But on the Sonata, the facia panel is in the center.

  • 2 Once you have found this module, you will want to ensure that the memory switch is in the OFF position. Then turn the ignition on.
  • 3 Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module.
  • 4 If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button.
  • 5 Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes. good luck my friend
  • Feb 08, 2012 | Hyundai Cars & Trucks

    2 Answers

    My 2001 pt cruiser auto door locks no longer work nor does the key fob. The door locks were acting like sssharp's - doing their own thing and locking or unlocking on their own and rattling in the back door...


    As stated above, it is most likely your RKE (remote keyless entry module). It is easy to find and relatively easy to replace yourself. I just recently did so on my 2002 PT Cruiser. Got a used module from a 2005 at a salvage yard. Put in the module myself. However, you do have to take it to the dealer to reprogram so your remotes work with the module replacement. That cost me $50. If you are interested in doing the labor yourself, email me. K4qts@aol.com

    Jul 06, 2010 | 2002 Chrysler PT Cruiser

    3 Answers

    How to program 2004 Hyundai Santa Fe Keyless Entry Remote


    Synchronization
    When
    System malfunction. Remote control added or replaced.
    How
    Access alarm system control module located under driver's side lower fascia Fig. 2 . Set memory switch to SET position. Press remote control lock or unlock button. Set memory switch to OFF position. Confirm synchronization has been successful by locking and unlocking vehicle. Repeat procedure for second remote control. Synchronization can also be carried out using diagnostic equipment.
    NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

    Mar 23, 2010 | 2004 Hyundai Santa Fe

    1 Answer

    Hyundai sonata 2002 remote


    There is a special (proprietary) programming electronics 'black box' for the keyless entry system on all Hyundai vehicles for programming the remotes. This programming is stored in either the BCM (body control module) or the ETACS module (Electronic Time and Control System).

    May 22, 2009 | Hyundai Motor 2002 Sonata

    2 Answers

    Program factory remote keyless entry: 2003 Hyundai XG350


    The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

    May 22, 2009 | Hyundai Motor 2003 XG350

    Not finding what you are looking for?
    Hyundai Motor 2002 Sonata Logo

    Related Topics:

    87 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8123 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...