Question about 1986 Ford Bronco II

Open Question

Wirering diagram for sunpro super tach 3 - 1986 Ford Bronco II

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 834 Answers

SOURCE: How do I install a

The Black wire will connect to body ground, and it should be a good solid ground and if this wire is not grounded well then you might receive a primary voltage shock if you touch anything that is metal or grounded inside of the vehicle when the engine is running.

The Red wire should be connected to power when the key is in the "Run" position only, and a good place to find that source is one of the "IGN" connections at the fuse panel using a covered female spade connector. Use a test light and be certain that the connection only has power when the key is in the "Run" position, and has no power when the key is in the "Off" or "Accessory" position.

The White or Yellow wire should connect to the "LPS" connection at the fuse panel next to the LPS fuse using a covered female spade connector.

The Green wire will connect to the "-" negative side of the ignition coil or to the "Tach" or "Test" lead that runs from the negative side of the ignition coil. To locate the lead run down the wire from the negative side of the ignition coil and the lead should break off from that wire and it should have a tag on the wire that will say either "Tach" or "Test" (sometimes it is just an empty black wire connector) and that is if the lead does not come straight off from the wire connector at the ignition coil. If there is no lead you can get a wire tap connector to tap into the wire from the negative side of the ignition coil and then use a covered male spade connector to connect the Green wire from the tachometer to the wire tap connector.

Here is a diagram to help assist you and if you can not download the image right click on the image and then select "save picture as..." or "save image as..." and from your image viewer you should be able to read this diagram or print it out, and let me know if you require any further assistance.


d756391.gif

Posted on Aug 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just bought a sunpro super tach2 and it shows that it is running to fast. whats the problem


There should be 2 adjustments on the back. A switch for 4-6-8 cyl use and a slider to fine tune the rpm. If you know your car idles at 750rpm, move the slider until the tach reads 750. The switch for cylinder numbers should be self-explanatory and must be set first.

Feb 12, 2015 | Cars & Trucks

1 Answer

Need a wirer diagram a lock up converter a2000 F450


We do not have wiring diagrams here a fixya. All this type of material is copy protected and not free to share. You can access the factory repair books here for a small change.

Sep 28, 2012 | 2000 Ford F350 Super Duty Super Cab

3 Answers

What does the check engine light mean on the 92 town car.


If lit, it means that a DTC or diagnostic trouble code is stored in the computer.
Have it scanned or get the DTC interpreted by looking up the code in the service manual.

HAND-HELD SCAN TOOLS Although stored codes may be read through the flashing of the CHECK ENGINE or SERVICE ENGINE SOON lamp, the use of hand-held scan tools such as Ford's Self-Test Automatic Readout (STAR) tester or the second generation SUPER STAR II tester or their equivalent is highly recommended. There are many manufacturers of these tools; the purchaser must be certain that the tool is proper for the intended use. The scan tool allows any stored faults to be read from the engine controller memory. Use of the scan tool provides additional data during troubleshooting, but does not eliminate the use of the charts. The scan tool makes collecting information easier, but an operator familiar with the system must correctly interpret the data. Fig. 1: Super Star II tester - Ford Motor Co. 84924047.gif
Fig. 2: Inexpensive scan tools, such as this Auto Xray® , are available to interface with your Ford vehicle tccs4p11.jpg
Fig. 3: An economically friendly alternative is this Code Scanner® from SunPro. They are purchased according to manufacturer and are available at many parts stores 91054p14.jpg
Fig. 4: The Code Scanner® from SunPro has no LCD display, just a LED that will flash out the codes and an audible buzzer to alert that the test is in progress 91054p16.jpg

Oct 14, 2010 | 1992 Lincoln Town Car

1 Answer

How do I install a Sunpro Super tach 3 in a 1987 Mustang 5.0


The Black wire will connect to body ground, and it should be a good solid ground and if this wire is not grounded well then you might receive a primary voltage shock if you touch anything that is metal or grounded inside of the vehicle when the engine is running.

The Red wire should be connected to power when the key is in the "Run" position only, and a good place to find that source is one of the "IGN" connections at the fuse panel using a covered female spade connector. Use a test light and be certain that the connection only has power when the key is in the "Run" position, and has no power when the key is in the "Off" or "Accessory" position.

The White or Yellow wire should connect to the "LPS" connection at the fuse panel next to the LPS fuse using a covered female spade connector.

The Green wire will connect to the "-" negative side of the ignition coil or to the "Tach" or "Test" lead that runs from the negative side of the ignition coil. To locate the lead run down the wire from the negative side of the ignition coil and the lead should break off from that wire and it should have a tag on the wire that will say either "Tach" or "Test" (sometimes it is just an empty black wire connector) and that is if the lead does not come straight off from the wire connector at the ignition coil. If there is no lead you can get a wire tap connector to tap into the wire from the negative side of the ignition coil and then use a covered male spade connector to connect the Green wire from the tachometer to the wire tap connector.

Here is a diagram to help assist you and if you can not download the image right click on the image and then select "save picture as..." or "save image as..." and from your image viewer you should be able to read this diagram or print it out, and let me know if you require any further assistance.


d756391.gif

Aug 20, 2010 | Ford Mustang Cars & Trucks

2 Answers

I have a high idle and the computer hasnt thrown a code. How do I fix this or what all could it be? I also hhave a sunpro tach and dont know what to hook it up to....?


if u own a 1989 sierra u dont have an obd or obd ll computer on board if high idle all time then search for a possible vacuum leak and or throttle/carb needs adjustment

May 24, 2010 | 1989 GMC Sierra

1 Answer

I have a sunpro after market tach. i need the color coded diagram to install it,can anyone help me?thanx


Tried going to sunpro online? paste this in and it should get you there:http://www.google.com/search?q=sunpro+tachometer+wiring&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US Ive always found that going to the source is better than getting it second-hand.

Apr 23, 2010 | Chevrolet Silverado Cars & Trucks

1 Answer

I1999 dodge ram 1500 5.2 and need to no how to put a tach in


Red wire would go to ignition battery, the black to ground. The third wire, probably green or blue, goes to the negative side of the ignition coil. Is there a wire for dash illumination?

Mar 10, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

How do I hook-up Sunpro Super tach 2. Wires: 1 each - green, red, white, and black? Or in general how do these type tachometers hook-up?


I've got an install diagram for that around here somewhere but for now, the trigger wire to run the tach itself goes to the "tach" connection next to the "Bat" terminal on the distributor cap. one wire attaches to your dash lighting so it comes on with the dash lights and dims properly, the other wire is likely a ground. If I don't add to this later, try googling Sun electronics...I am fairly sure they have an install page.

Jan 04, 2010 | 1985 Chevrolet K1500

1 Answer

I have a 1994 GMC Sonoma SL and it doesn't have a tach in it, so I brought one made by Sunpro. And my problem is I've never hooked one up. So is there anybody out there that can tell me how to do it? and...


Do you have the instructions that came with it? If not, you can get them online at the sunpro website:
http://www.sunpro.com/user_manuals.php
If you need more help, let me know

Aug 09, 2009 | GMC Sonoma Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...