Question about Cars & Trucks

1 Answer

Can't get to rear screws on steering column cover on 99 Honda Passport

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,113 Answers

You may need an offset screwdriver or a stubby screwdriver

Posted on Oct 15, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2039 Answers

SOURCE: Short in steering column wiring

torque bit 20 to remove the air bag bolt in the back cover stering puller stering puller to push plate phillip screw driver that about it pierre

Posted on Oct 19, 2008

  • 3 Answers

SOURCE: Cannot get to heater blower motor in 1993 Dodge Dakota

its a big job get yourself a hanes manual the module is the complete heater box underdash you have to pump down a/c. i put heater core and blower motor in a 95 dakota its not a fun thing to do

Posted on Dec 17, 2008

mrgreenz
  • 962 Answers

SOURCE: how can remove the starter of my honda passport 99

You have to drop the exhaust pipe and remove the wheel. I got his info from Wiki Answers hope it helps you.Read below.
. Disconnect the battery first. After that you may want to remove the driver's side front wheel. This gave us access to the starter for removal of the battery cable and the spade terminal which are on top of the starter while it is mounted. We then removed the two bolts that hold the starter in place. All of that took about 10 minutes to complete. On my passport the battery cable came off with a 12mm, the spade terminal is plug and play and all you have to do is push down on the tab on top and pull the terminal apart. The bolts for the starter are 14mm on my car. You need extensions to get at them though. After that is when all of the work began. We then tried every way possible to get it out of the compartment without taking anything else apart. No luck. So we removed the heat shields around the exhaust manifold and exhaust. Still not enough room. So finally we took the 3 bolts out of the flange that connects the exhaust manifold to the exhaust pipe. We had to use reverse torque bolt sockets for this. The one we used was the NAPA E-14. There are nuts on the bolts but removing only those won't do the trick. They are 17mm in case you are wondering. We then had to remove the bracket just aft (rearward) of the catalytic converter to get enough play in the exhaust pipe. Once you do this, the starter slides right out of the space moving down and aft. The new starter goes right in no problems once you are to this point. The only casualty to the whole process was one of the bolts from that flange on the exhaust manifold lost it's threads in the process. We were lucky that none of mine sheared off which is apparently a large concern and somewhat of a probability. Good luck

Posted on Jan 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a wiring problem in steering column of my 1998 ford f150 need to know how to take apart


If I recall right, on my 99 I had to take off the lower part of the dash to get access to the screws holding on the steering column covering.

Apr 12, 2016 | Ford Cars & Trucks

1 Answer

How do I change the shift interlock actuator on a 99 ford ranger?


Remove the steering column's upper and lower covers. Then remove the shift cable from actuator and then remove the electrical connector and then remove the screws to remove the actuator from the steering column.

Feb 25, 2015 | Ford Cars & Trucks

1 Answer

I have 1995 Honda passport SUV and my turn signals Dont work at all but my hazard lights do


If the hazards are working then remove the shroud around the steering column and check the switch for a feed its possible that the wires or a connection are damaged

Nov 04, 2014 | 1995 Honda Passport

1 Answer

Remove steering column cover 300m chrysler 1999


Hi Trevor, I'm glad to help!

The Steering Column Cover is held by 3 screws mounted upward and you reach them through the access holes from under the column. Some are Phillip's head screws and some are torx screws. Once the screws are out remove the top cover first, then the under cover next. Hope this helps and have an awesome day Trevor.

Mar 02, 2013 | 1999 Chrysler 300M

1 Answer

Highbeam switch


  1. If equipped, disable the SIR system. Disconnect the negative battery cable.
  2. Remove the upper steering column cover.
  3. Remove the lower steering column cover screws and lower the steering column cover.
  4. Remove the 2 switch mounting screws and remove the switch.
  5. Detach all wire connectors from the combination switch. Push locking tabs to remove the wires.

To install:

  1. Attach all wire connectors to the combination switch.
  2. Install the combination switch to the column with the 2 attaching screws.
  3. Install the lower steering column cover screws and lower steering column cover.
  4. Install the upper steering column cover and attaching screws.
  5. Connect the negative battery cable.
  6. Enable the SIR system, if equipped.

Dec 04, 2011 | 1999 Pontiac Sunfire

1 Answer

Cant figure out how to remove key cylender from a 99 honda civic


TURN OFF RADIO.DISCONNECT NEGATIVE BATTERY CABLE.WAIT 20 MINUTES FOR AIRBAGS TO DISCHARGE.YOU NEED TO REMOVE THE STEERING COLUMN COVERS AND LOWER INSTRUMENT PANEL COVER.REMOVE THE IGNITION SWITCH.REMOVE THE RETAINING NUTS AND LOWER THE STEERING COLUMN.THE LOCK ASSEMBLY IS CLAMPED BY TWO SHEAR HEAD BOLTS.USE A CENTER PUNCH TO MAKE A DIMPLE IN THE HEAD OF EACH BOLT,THEN DRILL THE HEAD OFF WITH A 3/16 INCH DRILL BIT.SEPARATE THE CLAMP AND REMOVE THE ASSEMBLY FROM THE STEERING COLUMN. PLACE THE NEW LOCK ASSEMBLY IN POSITION WITHOUT THE KEY INSERTED AND TIGHTEN THE BOLTS UNTIL THEY ARE SNUG.INSERT THE KEY AND CHECK THE LOCK CYLINDER FOR PROPER OPERATION. TIGHTEN THE BOLTS UNTIL THEIR HEADS BREAK OFF.TIGHTEN STEERING COLUMN TO INSTRUMENT PANEL FLANGE NUTS TO 108 INCH POUNDS.TIGHTEN THE RETAINING COLLAR CLAMP BOLTS TO 16 FT LBS.

Apr 29, 2011 | Honda Civic Cars & Trucks

1 Answer

Hi, i have 1991 mazda protege. I accidentally broke my key in the ignition lock and now i was wondering how do you take off the ignition lock cylinder? p.s key was pretty worn down already


Ignition Switch/Lock Cylinder REMOVAL AND INSTALLATION CAUTION
Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6. The ignition lock is an integral component of the steering lock mechanism. If the ignition lock must be replaced, perform the following procedure. Fig. 1: Exploded view of the ignition switch/lock cylinder assembly 89548g14.gif
Fig. 2: Remove the break-off head retaining bolts by chiseling a slot in the bolt, then removing them with a screwdriver 89548g15.gif
Millenia
  1. Disconnect the negative battery cable.
  2. Properly disarm the air bag system.
  3. Remove the rear console box, brake boot and center panel (disconnect the harness connectors).
  4. Remove the rear console.
  5. Remove the undercover, glove compartment and compartment cover.
  6. Remove the upper and lower steering column covers.
  7. Tilt the steering shaft down. Remove the cap and panel light control switch. Remove the meter hood mounting screws. Pull the meter hood forward to disengage the clips.
  8. Remove the instrument cluster,
  9. Remove the drivers side air bag and the steering wheel.
  10. Remove the combination switch.
  11. Remove the passenger side air bag mounting bolts, electrical connector and remove the air bag module.
  12. Remove the hood panel release lever. Pull the side panel forward to disengage the clips, remove the side panel.
  13. Remove the side covers.
  14. Remove the dashboard mounting bolts, pull the dashboard up and forward and remove.
  15. Remove the steering shaft.
  16. Remove the screw and the ignition switch and disconnect the ignition switch connector.
  17. Using a chisel and a hammer make a groove in the heads of the steering lock mounting bolts. Remove the bolts and the steering lock assembly. To install:
  18. Install the steering lock mechanism to the steering column jacket. Make sure that the lock operates correctly. Install new mounting bolts and tighten the bolts till the heads break off.
  19. Reconnect the ignition switch connector to the ignition switch and install the ignition switch to the steering lock mechanism with the screw.
  20. Replace the dashboard close to its mounts and connect all harness connectors. Install all mounting bolts. Torque to 14-18 ft. lbs. (19-25 Nm).
  21. Install the side covers.
  22. Instal the side panels.
  23. Install the steering shaft and torque the mounting bolts to 12-16 ft. lbs. (16-22 Nm).
  24. Connect the passenger side air bag module electrical connector and replace the module to the dash and install the mounting bolts.
  25. Install the combination switch on the steering column.
  26. Install the steering wheel and drivers side air bag module.
  27. Install the instrument cluster.
  28. Install the meter hood.
  29. Install the upper and lower steering column covers.
  30. Install the glove compartment cover, compartment and the undercover.
  31. Install the rear console, bracket, center panel, brake lever boot and the rear console box.
  32. Reconnect the negative battery cable,
  33. Place the steering column securely on a workbench. Use a chisel and hammer to make slots in the head of the lock screws. Remove the screws.
Except Millenia
  1. Disconnect the negative battery cable.
  2. If equipped, disarm and remove the air bag.
  3. Remove the steering wheel and the combination switch.
  4. Remove the steering column by performing the following:
    1. Remove the driver's side under dash covers.
    2. If equipped, disconnect the key interlock cable from the steering column.
    3. Detach any remaining electrical wire harness connectors from the column.
    4. Remove the upper column-to-dash mounting bolts. Support the steering column.
    5. Remove the intermediate shaft-to-steering column shaft coupling bolt and remove the steering column-to-firewall bracket bolts/nuts.
    6. Remove the steering column from the vehicle.
  5. Place the steering column securely on a workbench. Use a chisel and hammer to make slots in the head of the lock screws. Remove the screws.
  6. Remove the ignition lock assembly. To install:
  7. Position the ignition lock and bracket on the steering column.
  8. Install the new screws until the head twists off. Make sure the lock operates properly while tightening the new locking screws.
  9. The remainder of the installation is the reverse of the removal procedure.
prev.gif next.gif

Feb 12, 2011 | 1993 Mazda Protege

1 Answer

How to remove a heator core from a 2001 dodge caravan? do you have to take the dash out? or just the bottom pannel.


The 2001 Dodge caravan has 2 heater cores - front (the main one), and the rear. Removal of the
rear heater core is a whole different procedure than the front.

Front Heater Core - Removal and Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Align the wheels in the straight-ahead position.
  3. Disconnect the negative battery cable.
    CAUTION Before working around the steering wheel or the instrument panel all 2 minutes to pass to allow the air bag module to discharge.
  4. Drain the cooling system into a clean container for reuse.
  5. Remove the steering column, by removing or disconnect the following:

    Lower left side steering column cover Parking brake release cable from the parking brake lever 10 steering column cover liner-to-instrument panel bolts and the cover liner
  6. Rotate the key to the LOCK position; then, rotate the steering wheel to the LOCKED position.

    Gear selector cable and its mounting bracket as an assembly from the upper steering column mounting bracket 2 instrument cluster trim bezel-to-instrument panel screws, retaining clips and bezel 2 steering column shroud-to-steering column screws and the shroud Steering column-to-intermediate steering shaft coupler
  7. Loosen but do not remove the 2 lower steering column mounting bracket nuts/washers.

    2 upper steering column mounting bracket nuts/washers Steering column assembly from the vehicle
  8. Remove or disconnect the following:

    Instrument panel-to-chassis harness interconnect and bracket Lower silencer boot, at the base of the steering shaft
  9. Working in the engine compartment, pinch off the heater hoses.

    Heater core cover. Position some towels under the heater core hoses. Heater core plate and the hoses
  10. Depress the heater core retaining clips.
  11. Lift the accelerator pedal and slide the heater core past it.
  12. Depress the brake pedal and remove the heater core from the heater/air conditioning housing assembly.

    0996b43f8022fa83.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the steering column assembly


    0996b43f8022fa84.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the interconnect and bracket


    0996b43f8022fa85.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the front heater core assembly


To install:
  1. Depress the brake pedal and install the heater core into the heater/air conditioning housing assembly.
  2. Lift the accelerator pedal and slide the heater core past it.
  3. Install or connect the following:

    Heater hoses (using new O-rings) and the heater core plate Heater core cover Heater hoses clamps, working in the engine compartment Lower silencer boot at the base of the steering shaft Instrument panel-to-chassis harness interconnect and bracket
  4. Install the steering column assembly by installing or connect the following:

    Steering column assembly, carefully into the vehicle. 2 upper and 2 lower steering column mounting bracket nuts/washers. Torque the nuts to 105 inch lbs. (12 Nm). Steering column-to-intermediate steering shaft coupler and tighten the pinch bolt to 21 ft. lbs. (28 Nm) 2 steering column shroud and the shroud-to-steering column screws Bezel, the retaining clips and the 2 instrument cluster trim bezel-to-instrument panel screws Gear selector cable and its mounting bracket as an assembly to the upper steering column mounting bracket 10 steering column cover liner and the cover liner-to-instrument panel bolts Parking brake release cable to the parking brake lever Lower left side steering column cover. Lower left side steering column cover
  5. Refill the cooling system.
  6. Connect the negative battery cable.
  7. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Jan 02, 2011 | 2001 Dodge Caravan

1 Answer

2006 hhr to take out ignition switch out


Removal & Installation

1. Disable the SIR system.


28d6a49.gif
Remove the Instrument Panel (I/P) center trim panel by releasing the retaining fasteners

  1. Remove the Instrument Panel (I/P) center trim panel (1) by pulling out on the trim panel in order to release the retaining fasteners (2).
  2. Disconnect the electrical connectors on the Instrument Panel (I/P) center trim panel (1).

dc7f057.gif
Remove the steering column opening filler assembly, with clip, & bumper

3. Remove the steering column opening filler assembly (1) by pulling away the clips (2).
4. Disconnect the electrical connector for the trunk release.


77e0f1d.gif

Remove the Instrument Panel (I/P) left side trim panel

  1. Remove the Instrument Panel (I/P) left side trim panel (1).
  2. Tilt the steering wheel up.
  3. Disconnect the I/P dimmer switch and, if equipped, the fog lamp switch.

88e8dec.gif

Remove the 4 bezel screws (2) & the Instrument Panel (I/P) cluster bezel assembly (1)

  1. Tilt the steering wheel down.
  2. Remove the 4 instrument panel cluster bezel screws.
  3. Remove the instrument panel cluster bezel.

810fe4a.gif

Remove the steering column trim covers: steering column upper cover assembly, steering column left cover assembly, & steering column right cover assembly

Remove the steering column trim covers:
  • Remove the 3 cover screws (4).
  • Remove the steering column upper cover assembly (1).
  • Remove the steering column left cover assembly (2).
  • Remove the steering column right cover assembly (3).


bd6042a.gif
Removal of the ignition switch

    1. Disconnect the ignition switch harness connector.
    1. WARNING
    The ignition switch must be in the run position during removal in order to avoid damage to the ignition switch.

    1. Turn the ignition switch to the run position.
    2. Remove the ignition switch screws.
    3. Remove the ignition switch from the steering column.
    To install:
    1. Install the ignition switch and screws on to the steering column. Tighten the screws to 17 inch lbs. (2 Nm).
    2. Connect the ignition switch harness connector.
    3. Installation is the reverse of removal procedure.
    4. Tighten the trim cover screws to 17 inch lbs. (2 Nm)
    5. Tighten the 4 instrument panel cluster bezel screws to 19 inch lbs. (2 Nm)
    6. Enable the SIR system. Refer to Air Bag (Supplemental Restraint System), arming the system.
      NOTE If the ignition switch is replaced and a learn procedure is not performed, the engine will crank but not start or will start and stall immediately.

    7. Perform the vehicle theft deterrent system learn procedure.

    Mar 12, 2010 | 2006 Chevrolet HHR

    1 Answer

    I have a 1995 Honda passport and I donot have a manual to it and need to find out if there is 2 fuse panles or just one.


    there are two fuse panels on the 95 passport, one inside to the left of the steering wheel, it is labeled on the cover, the second panel is under the hood to the rear of the battery

    Mar 25, 2009 | 1995 Honda Passport

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    19 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...