Question about 1992 Isuzu Rodeo

1 Answer

How can i remove my axle bearing for a 1992 isuzu rodeo

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 14 Answers

If it's a rear axle bearing.....your best bet would be to remove the hub\bearing housing\axle assembly and take it to a shop to have it pressed out and new pressed back in. Make sure the seal is done at the same time.......There are a number of manuals (eg. Chiltons) that cover axle removal and replacement.

Posted on Dec 05, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Richie_asg1
  • 1036 Answers

SOURCE: 1992 Isuzu Rodeo Distributor wires

Hi,

On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.

Cylinder numbering .

88c39f7.jpg-

Hope this works for you

Posted on Jul 05, 2008

j_del
  • 1586 Answers

SOURCE: Rear Axle Bearing Replacement

That absolutely sounds like an axle (wheel) bearing. Jack up that corner of the truck and grab the top and bottom of the wheel, and shake like crazy. If you have any play whatsoever, it's a sign of a bad bearing (although you could have a bad one and not have any play - it would only mean the bearing isn't worn badly enough to cause looseness in the wheel).

You should be able to remove the axles without opening the diff up. If the axles have c-clips or snap rings on the ends inside the diff, you can usually get the axles out by dismounting them from the hubs and getting them free of all attachment except the diff, and then use a large flat-tip screwdriver as a pry bar. Use it right where the axle body mates to the diff, and lever it while you pull/yank/shake/swear at the axle, and you'll manage to pop the axle out of the diff. Sometimes it takes some time and profanity, but so far it's worked for me everytime.

Posted on Aug 02, 2008

germcelchar
  • 389 Answers

SOURCE: how do i remove cv axle for a 98 isuzu trooper

Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I NEED TO SEE A SCHEMATIC PICURE OF WHEEL BEARINGS ON THE FRONT WHEEL 4 WHEEL DRIVE OF A 1992 RODEO ISUZU


Check with local parts store they often have blowup they can print off or purchase a vehicle specific repair manual..Chilton or haynes are best.

Aug 24, 2016 | 1992 Isuzu Rodeo

1 Answer

What caused the rear wheel to fall off my 1992 Isuzu rodeo


Did just the wheel fall off or did the axle come out with the wheel attached?

Nov 02, 2013 | 1992 Isuzu Rodeo

2 Answers

Whining in transmission


If the noise was not there before any work was done
recently,then you may be on to something

I would say the whining is in the trans,front input bearing
One of those things you just have to replace & see what happens
That is a home project,not one you pay someone to do
& have no idea what was done

I do all my own work, so I can learn things & control the process

I have all drive shafts checked for being straight,install or have
installed all new joints & always have them balanced

I have all flywheels & clutch assy balanced,only when it it necessary
to have things apart to start with

Sep 12, 2012 | 1992 Isuzu Rodeo

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

Removing lower ball joint ball joint is removed to


Pull steering knuckle/bearing off axle

Dec 11, 2010 | 1999 Isuzu Rodeo

1 Answer

The housing where the rear axle bearing sits is bent up-ward slightly. This was caused by the axle breaking in half while being under to much stress. My question is will this cause problems when i replace...


Yes. It will keep the new axle under stress and probably break it again. Better to replace the housingat the same time. Check your local scrap yard for a used one.

Jun 22, 2009 | 1992 Isuzu Rodeo

1 Answer

Cv joint removal


Get the replacement cv axle and remove inner boot and clip and bearings. Do the same on the old axle. Replace bearing clip, cv shaft and reassemble. Do not try to remove the part from inside the front axle unless you want to spend about six hours of time and money.

May 12, 2009 | 1999 Isuzu Rodeo

1 Answer

Rear Axle Bearing Replacement


That absolutely sounds like an axle (wheel) bearing. Jack up that corner of the truck and grab the top and bottom of the wheel, and shake like crazy. If you have any play whatsoever, it's a sign of a bad bearing (although you could have a bad one and not have any play - it would only mean the bearing isn't worn badly enough to cause looseness in the wheel).

You should be able to remove the axles without opening the diff up. If the axles have c-clips or snap rings on the ends inside the diff, you can usually get the axles out by dismounting them from the hubs and getting them free of all attachment except the diff, and then use a large flat-tip screwdriver as a pry bar. Use it right where the axle body mates to the diff, and lever it while you pull/yank/shake/swear at the axle, and you'll manage to pop the axle out of the diff. Sometimes it takes some time and profanity, but so far it's worked for me everytime.

Jul 30, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...