Question about Cars & Trucks

1 Answer

Does anybody know what rig mats is? I have been trying to look to see what it is but I don't understand.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,113 Answers

I do now... thanks for that term. I googled it and switched to images and could see instantly what it is. It's like a metal frame with lumber in it. It's total height seems to be 2 inches wikipedia says that they are 6 feet X 30 feet or up to 8 feet X 40 feet. there are rubber versions and others as well

Posted on Oct 15, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2000 Nissan frontier- I'm trying to rig a horn

You Have Got A Direct Short
Does Your Horn Have Two Connections Too It?
If It Does Then Swop Your Wires Around And Try Again
Is You Vehicle Positive Or Negative Earth?Try Removing Horn From Vehicle And Test It On The Bench First!!
Let Me Know How You Get Along.
Good Luck

Mar 18, 2013 | Cars & Trucks

1 Answer

Brake lights dont work on my 1986 toyota 4runner. tried everything. anybody have any suggestions?

does yuor truck has a hitch harness? check your towing lights controler sometimes behind L tail ligth, just follow your harness, back track power, don't know what you have done but hope this helps.

Jul 28, 2012 | 1986 Toyota 4Runner

1 Answer

My 2000 Toyota Camry LE with 4 cylinder engine has hesitation upon acceleration from the stop idle point. This still happens even with the floor mats taken out. What's up. Thanks, Chas

don't know what the mats would have to do with this , unless they blocked the travel of the gas pedal,, but anyway ,, check the rotor and the distributor cap for worn or bad spots,, clean them off then try again, your plugs could be worn, and need replacement,, and also , if you have fuel injection,, clean the throttle body, remove the air cleaner tube from the motor, and spray some carb cleaner into the opening, , open the flapper plate and clean that too, wipe off any excess with a clean rag, those are basic steps to check when having the problem your having, if none of this helps ,, then replace the idle control sensor

Sep 23, 2011 | Toyota Camry Cars & Trucks

1 Answer

Underneath driver side floor mat is damp. I don't

if it is slippery and stinky, your heater core is leaking. otherwise you have a leak around your windshield and rainwater is coming in and not drying out as it is under the mat. very hard to track down, get some clear aquarium sealer and get to work.

May 10, 2011 | 2000 GMC New Sierra 1500

1 Answer

Lookin for the coolint tempiture sending unit on the motor in a 140 volvo excavator

Don't know your rig but most coolant sensors are near the inlet to the radiator and that is located at the bottom tank. They don't measure the engine temperature but do sit in the coolant stream as described.

Apr 21, 2011 | Volvo 240 Cars & Trucks

1 Answer

I have a 2001 lexus gs430 I turned the air on and nothing blows out of the vents trying to locate blower motor but don`t know where it is. Does anybody have an idea.

The blower is located above the front passenger foot well. You will probably have to remove some trim panels to get access to it.

Jun 19, 2010 | 2001 Lexus Gs 430

1 Answer

Engine power reduceed

clean the throttle body and replace the mass air flow sensor a know good one and see if that fixes it if it does you found your problem. normally the mass air flow sensor would cause the rig to run crappy atany speed.

Jun 25, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

Have 90 honda accord and s-light stays on causing rpm to go to 3-4 and won't go down

You have a bad transmission control module (TCM). It is under the passenger side front floor mat. You can get rebuilt units off Ebay, whatever you do, don't get a used one! They are all bad. If you know anybody that does electronic repairs, you can have them replace the big 220 uf capacitor on the PC board in the TCM. It's a two dollar part and a ten minute job but you have to know what you're doing. This will fix your problem I promise. Don't let anyone sell you a transmission!

Mar 29, 2009 | 1992 Honda Accord

1 Answer

2002 chevrolet silverado 2 wheel drive that rattles when you drive down a bumpy road. It seems worse when you first take off in the morning, but after you drive it for a while the noise seems to not be as...

Personally, I would start looking at the exhaust system shields and hangers. Make sure they are secure and not too close to the exhaust components. Minimum clearance for the shields is 20mm ( roughly 3/4"). You might be able to get away with a little less, but move or bend to get additional clearance.
Also make sure the spare tire rigging is secure, always a culprit.
Let me know how it goes,

Feb 25, 2009 | 2002 Chevrolet Silverado 1500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides