Question about Chevrolet Cars & Trucks

1 Answer

When i put my car into gear it will not move and its not the transmission because i already checked it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 880 Answers

Brakes locked up?

Posted on Nov 03, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: clutch or transmission problems

Check out your gear linkage and gearbox mounting. If that is fine then It could be the clutch. Sorry for the bad news.

Posted on Nov 29, 2008

  • 14036 Answers

SOURCE: 1996 chevrolet lumina minivan transmission problems

replace fluid and filter.if it dont help . low fluid level could have burn out your forward clutch plates.

Posted on May 17, 2009

  • 53 Answers

SOURCE: My car has a problem with reverse gear, forward

could be a bent selector or might just need to tighten it up

Posted on Jul 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

When i start my car and go to put it in gear it wont move.


When you say rocky spot, what do you mean? If you mean there were rocks in the roadway, you could have put a small hole in the transmission pan which leaked all the fluid out of it. First thing I would do is check the fluid level on the transmission dipstick and look for leaks on the ground under the car.

May 01, 2015 | 2002 Ford Taurus

1 Answer

2007 pt cruiser crankz up but wont move in neither gear i tried putting it all gears but the car wouldnt move,can u please help me with this problem thankz


CHECK TRANSMISSION FLUID LEVEL NEED TO DO TRANSMISSION FLUID CHANGE AND FILTER CHANGE,ADJUST BANDS EVERY 15000 MILES INTERVALS. CODE SCAN FOR FAULTY TRANSMISSION FLUID PRESSURE SWITCH OR FAULT IN TRANSMISSION SHIFT SOLENOID.

Jul 08, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Have an 05 cobalt with 110,000 mile. Car only moves while in reverse. When in drive or any other gear, the gear does nothing. I can move the shifter freely, but like I said. Unless in reverse, it...


CHECK TRANSMISSION FLUID LEVEL.IF OKAY.IF YOU HAVE NOT ALREADY DONE YET TRANSMISSION FLUID AND FILTER CHANGE IS DUE AT 100000 MILES.IF ALL IS GOOD YOU COULD HAVE FAULTY TRANSMISSION RANGE SWITCH.HAVE TRANSMISSION CODE SCAN FOR TRANSMISSION FAULT CODES.

May 24, 2011 | 2005 Chevrolet Cobalt

1 Answer

I just changed my honda element 2005 transmission fluid 2wks ago.I woke up this morning, start the car and put the gear stick to drive but the car will not move.What could be the problem? It is an...


You may need to find out if the transmission has a leak or is a cvt type of transmission.If the vehicle has a cvt transmission and the incorrect fluid type was used can cause major problems.You should contact the facility that performed your service. If the shop that performed your service used the wrong fluid type the liability falls to them for repairs unless you changed fluid because there was an issue already. If it was just maintenance to have serviced the tranny and this is end result definitely contact the repair facility.

Mar 14, 2011 | 2005 Honda Element

1 Answer

Car engine starts but does not move


Something you can try, but you would have to be very lucky for this to be the problem.

If you haven't already, check your transmission fluid level. If the fluid level gets low enough in the transmission it can cause the car to not move at all.

Please do the following, unless you already have;

Start the engine and let it run 6 to 8 minutes to allow the engine and fluids to reach normal operating temperature.

Remove the dip stick to the transmission fluid, wipe it off, put it back in, and then take it out again to read it. If there is no fluid on the dip stick, add 3/4 of a quart of transmission fluid in through the pipe that you took the dip stick out of. Put it in gear and see if there's any diference, if not, add the other 1/4 of the bottle and then try to put it in gear again and see if it will move.

Continue adding 1/4 of a quart at a time until the car starts to move, or the transmission level showing on the dip stick is where it should be.

Best of luck!

Jan 29, 2011 | 1984 Mazda 626

1 Answer

Our Isuzu Fuego LS 4x2 Manual Transmission doesn't move even the shift stick is already palced in First Gear, even in second gear and third gear and fifth gear also no reverse, to sum up only 4th gear will...


you may have a shaft key broken in the transmission. 4th is usually 1-1 drive and does not need the key. before removing the transmission, check to make sure the linkage is OK by shifting gears at the transmission. If you can get other gears at the transmission, then the problem is the shifter.

Oct 16, 2010 | Isuzu Pickup Cars & Trucks

1 Answer

Transmission issues revving up and not going in gear smoothly


I sounds like you may be low on transmission fluid. Its hard to say with the limited information yuo have given. If you put it into drive and the vehicle sits there and you give it gas and the engine revs up and then slowly starts moving, it is a transmission problem. If it is low you may have already done irreversible damage. The problem will get worse very quickly. Check your trans fluid immediately.

Sep 16, 2010 | 2004 GMC Sierra

1 Answer

2003 gmc yukon won't move when i put in drive or reverse


Hello. If you havent already done so check your transmission fluid with the car ideling. If its not moving it definatly sounds like a transmission problem. The tire should have nothing to do with this unless you put huge mud tires on it without properly adjusting gear ratio. That could possibly fry the transmission, but the difference in size would have to be pretty big compared to the old tires.

Mar 15, 2009 | 2003 GMC Yukon

1 Answer

Transmission or cv joints?


It sounds like the Universal Joints are out on the Driveshaft.

Jan 22, 2009 | 1999 Oldsmobile Intrigue

2 Answers

Clutch or transmission problems


Check out your gear linkage and gearbox mounting. If that is fine then It could be the clutch. Sorry for the bad news.

Aug 17, 2008 | 1989 Volkswagen Cabriolet

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...