Question about Cars & Trucks

Open Question

There a black box on the drivers side on the firewall. one of the hoses go to the brake boster other hose goes to the a/c and there's another place where a hose is suppose to go it has a S beside it, but I don't know where it hooks up too. I need a hose diagram for it.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ginko
  • 19396 Answers

SOURCE: Vacuum hose diagram

The rubber vacuum hose comes off the intake manifold inside the engine compartment.
The vacuum lines are located on left side fender, under the hood.
If you look facing motor you will see tehm on the right side.

Posted on Mar 15, 2009

Ad
  • 3 Answers

SOURCE: replacing front driver side (F150) brake line (rubber hose)

Brake fluid is highly corrosive. If you can't get the line loose on the frame side then I would suggest replacing the hard line as well coming from the master cylinder. Or if you have a flaring tool you could cut the hard line just behind the rubber and put a new fitting on it. Pretty easy if you have the tool. Essentially you will wind up kinking or breaking the hard line anyway if the fitting won't come loose easy.

Posted on Apr 04, 2009

jturcotte
  • 8274 Answers

SOURCE: There is a black control

this is your evap cannister and/or purge valve. See picks and system operation below.

d486436.gif



ec5154f.gif


OPERATION Changes in atmospheric temperature cause fuel tanks to breathe, that is, the air within the tank expands and contracts with outside temperature changes. If an unsealed system was used, when the temperature rises, air would escape through the tank vent tube or the vent in the tank cap. The air which escapes contains gasoline vapors.
The Evaporative Emission Control System provides a sealed fuel system with the capability to store and condense fuel vapors. When the fuel evaporates in the fuel tank, the vapor passes through the EVAP emission valve, through vent hoses or tubes to a carbon filled evaporative canister. When the engine is operating the vapors are drawn into the intake manifold and burned during combustion..
A sealed, maintenance free evaporative canister is used. The canister is filled with granules of an activated carbon mixture. Fuel vapors entering the canister are absorbed by the charcoal granules. A vent cap is located on the top of the canister to provide fresh air to the canister when it is being purged. The vent cap opens to provide fresh air into the canister, which circulates through the charcoal, releasing trapped vapors and carrying them to the engine to be burned.
Fuel tank pressure vents fuel vapors into the canister. They are held in the canister until they can be drawn into the intake manifold. The canister purge valve allows the canister to be purged at a pre-determined time and engine operating conditions.
Vacuum to the canister is controlled by the canister purge valve. The valve is operated by the PCM. The PCM regulates the valve by switching the ground circuit on and off based on engine operating conditions. When energized, the valve prevents vacuum from reaching the canister. When not energized the valve allows vacuum to purge the vapors from the canister.
During warm up and for a specified time after hot starts, the PCM energizes (grounds) the valve preventing vacuum from reaching the canister. When the engine temperature reaches the operating level of about 120°F (49°C), the PCM removes the ground from the valve allowing vacuum to flow through the canister and purges vapors through the throttle body. During certain idle conditions, the purge valve may be grounded to control fuel mixture calibrations.
The fuel tank is sealed with a pressure-vacuum relief filler cap. The relief valve in the cap is a safety feature, preventing excessive pressure or vacuum in the fuel tank. If the cap is malfunctioning, and needs to be replaced, ensure that the replacement is the identical cap to ensure correct system operation.
OBD-II EVAP System Monitor
Some of the models covered in this guide have added system components due to the EVAP system monitor incorporated in the OBD-II engine control system. A pressure sensor is mounted on the fuel tank which measures pressure inside the tank, and a purge flow sensor measures the flow of the gases from the canister into the engine. The purge valve is now called the Vapor Management Valve (VMV). It performs the same functions as the purge valve, however it looks slightly different. A canister vent solenoid is mounted on the canister, taking the place of the vent cap, providing a source of fresh air to the canister.
The PCM can store trouble codes for EVAP system performance, a list of the codes is provided later in this information. Normal testing procedure can be used, see EVAP System Component Testing in this Section.

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vent solenoid location on a 2003 sunfire


On a 2002 Sunfire, the fuel vapor canister purge solenoid (AKA canister vent solenoid) is between the engine and the firewall, up high near the hood. It's a black box with two hose or fuel vapor line ports going toward the passenger side and one toward the driver side. One of the passenger side hoses goes to the vapor canister.

Apr 25, 2014 | 2003 Pontiac Sunfire

Tip

How To Replace A Heater Core 1995 Olds Aurora


Start inside the vehicle on the drivers side, remove the drivers side bottom dashboard plastic panels, you'll need to pop out the switches on either side of the steering column to access the 10mm bolts that hold the plastic panel, and steel panel under it. Working directly in front of the console above the floor, by the firewall, will be a black plastic cover on top of another black plastic cover. They are held in by 5.5 mm screws. Once both panels are removed, you will finally see the heater core. There are 2 straps that hold the heater core in place. Remove the 5.5 mm screws that hold the straps to the housing. Now, from under the hood, around the center of the firewall, there will be a rectanglar shaped vacuum box mounted on top of a relay bracket, remove to 3 10mm nuts to move vacuum box and relay bracket out of the way to access the heater core hoses. It may help to, from the inside, push the heater core forward thru the firewall, and then from under the hood, cut the aluminum tubes a inch or so from the heater hoses, a long sharp edge flat blade screwdriver might help. You can do this from inside the car, but watch for anti freeze. Remove the hog ring clamps, vice grips might help, in removing them. Use alot of WD-40, by spraying between the hose and the tubing, use a thin screwdriver between the hose and tubing to break the seal of the rubber hose to the tubing. Remove the 2 tubing pieces from the heater hoses. You are ready to reassemble. I'd replace the clamps with some worm gear clamps, alot easier to deal with.

on Mar 07, 2010 | Oldsmobile Aurora Cars & Trucks

1 Answer

Break system boster . the part thats connected to the peadle has seal that is broken. i need to know the name of the part and how to replace it.


The name is exactly that "Brake Booster" To remove it: Remove the master cylinder assembly and vacuum hoses from the booster. On the interior side of the firewall you will have to unbolt the booster and disconnect the linkage attaching the pedal to the piston in the booster.

Feb 25, 2011 | 1994 Dodge Intrepid

1 Answer

I have a 1996 suburban.. a pack rat ate the hose... I think it is a vacuum brake hose it runs from behind the brake fluid reservoir to the engine block .. it fits under a black box that is ontip of the...


not sure what the black box is but that is the vacuum hose that goes to the brake booster. You should be able to repair it with bulk hose or you could order it as a preformed hose from a dealer. Just make sure the hose doesn't kink the way you have it routed.

Oct 20, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Brake pedal hard to press down,1995 ford fairmont


chek a vacuum hose or the boster valve , maybe brake fluid inside the brake boster

Aug 11, 2010 | 1983 Ford Fairmont

1 Answer

Water leaking into 2005 Camry 6 cyl under carpet drivers side.


I think that I can help you. It sounds like your drain-tube is plugged up. Get in the passenger side, and pull the carpet back from under the glove box. Look for a black rubber pipe that goes from a black box, and pokes thru the firewall, on the passenger side. Remove the hose from the box, and have a container ready to catch water. If water comes out of the black box, your drain hose is plugged up. Clean out the clog, and you will be golden.

Jul 27, 2009 | 2005 Toyota Corolla

1 Answer

Where is the ac drain hose


Normal 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} -- open the driver's door
-- locate where the air conditioner blower box is attached to the passenger side of the firewall – see photo #1 – look to the immediate right at the top of the gas pedal arm
474e59d.jpg
-- condensation flows toward the front of the vehicle through the firewall at the leftmost edge of the air conditioner blower box – drain channel
-- open the hood and stand next to the front wheel on the driver's side
-- look down at the firewall over the battery and to the passenger side of the brake master cylinder – see photo #2
7fa75c5.jpg
-- locate the small diameter metal tubes running horizontally and attached to the engine compartment firewall
-- locate the hole in the engine compartment firewall panel behind the small diameter metal tubes
-- this hole leads to the drain opening in the air conditioner blower box mounted in the passenger compartment
-- follow the brake tubes as they run from under the vehicle and turn toward the front wheel on the driver's side
-- locate the hole in the engine compartment panel behind the brake tubes
-- insert a short length of stiff wire into the hole through the engine compartment panel to unblock the drain hole

Jul 11, 2009 | 2004 Mitsubishi Endeavor

2 Answers

Air flow wont change from defrost to other positions.


The AC functions of defrost, vent and floor are controlled by vacuum motors, you have a vacuum loss problem from the engine, check for a small disconnected vacuum hose under the hood from the engine to the firewall..

Jul 01, 2009 | 2002 Jeep Wrangler

2 Answers

1992 honda ex


The Freon goes into the "suction" hose/pipe assembly. There will be a service port on this hose. The low side (blue) hose of the manifold gauge set gets connected to this fitting. The suction hose can be identified by it's larger diameter (compared to the discharge and liquid hoses). The suction hose will run from the compressor across the top of the radiator (slightly behind the radiator), then back towards the firewall on the passenger's side of the engine compartment. The service port is generally closer to the firewall, than to the compressor.

Aug 31, 2008 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...