Question about 2001 Chrysler PT Cruiser

1 Answer

How do you remove panel to get to driver side window motor on 95 crown vic

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There should be two phillips screws in the door panel, one at the very bottom of the door in the center. The second screw is behind the plastic piece that is behind the door handle. You will need a flat head screw driver or small pry tool to get the plastic part out, I use a nylon polymer pry tool so as not to damage the plastic. Once the two screws are removed, you lift the door panel straight up about two inches then pull it away from the door. You will have to disconnect some wires for the window switches, locks, etc. Its always recommended you disconnect your negative battery terminal prior to connecting/disconnecting any electrical components in your car

Posted on Dec 11, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
junmag
  • 175 Answers

SOURCE: Power window does not work

you need to buy or make a clip removal tool. it looks like a sturdy 2 prong fork to pry off the plastic clips.this id whats holding the interior panel and some screws holding the door opener

Posted on May 30, 2009

  • 1986 Answers

SOURCE: How to remove interior door panel on 2002 chrysler t & c???

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 251 Answers

SOURCE: have no manual, need to remove driver door panel

rremove screws holding handle lift up on panel it has "hooks"

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2007 crown victoria driver side window wont go up or down what's the problem ?


if it is electric window check fuse box or the window motor or the connections or switch

Jan 24, 2016 | Cars & Trucks

3 Answers

On my 2000 ford crown vic. the power door locks work except for the drivers side. sounds like something is rattleing in the door. any ideas on what and how to fix


the power lock in that door may have broke the rod. remove the door panel to inspect its operation and replace the necessary part. hope this helps

Jan 31, 2011 | 2000 Ford Crown Victoria

1 Answer

Can I use front window motor for back window?


This is going to sound wrong, but I have been told the window motors will match but not on the same side. For some reason they are crisscrossed. The drivers front matches the passengers side rear motor. The passengers front matches the drivers rear motor.

So basically there are only 2 part numbers for the 4 motors. I was lucky enough to find the exact motor in the identical door I was having to repair on my 1994 Crown Vic. I was thinking to use the front passenger motor for the front drivers motor and thats when I learned about window motors.

Aug 28, 2010 | 1995 Mercury Grand Marquis

1 Answer

Rear axel removal 95 crown vic


simple!remove wheels wich ever side remove drums or rotors remove rear pumpkin cover! spin gears til u see an 8 mm pin! remove pin/bolt then slide larger pin out ! k push axl in c clip will fall out remove axl ! to install reverse!

Mar 18, 2010 | 1999 Ford Crown Victoria

3 Answers

94 crown vic driver power window does not work can


The window regulator can be broke. Its made of plastic and they break often.

May 03, 2009 | 1994 Ford Crown Victoria

2 Answers

Driver Side Front Window Replacement


You just drop it down from the top at a slight angle. Then put the bolts back in and check to make sure that it moves freely.

Dec 21, 2008 | 1993 Ford Crown Victoria

1 Answer

2004 crown victoria lx smashed driver side window


normally you have to loosen the track and it comes out as one whole assembly stop by a dealer in the parts department and ask them to print out a diagram or show them the part you are having the problem with

Aug 27, 2008 | 2003 Ford Crown Victoria

1 Answer

2003 cvpi wing mirror


first of all if you have the new mirror off of a crown vic or grand marquise there is nothing to worry about wiring because you have to take the door panel off and once off all you have to do is plug in the new mirror the same way you took the old one off

Aug 14, 2008 | 2003 Ford Crown Victoria

1 Answer

2002 crown vic


you need to jack that side of the engine up. take the right side motor mount bolt loose then jack the engine up from underneath. be sure to use a block of wood or somthing so you dont bust the oil pan

Jul 22, 2008 | 2002 Ford Crown Victoria

2 Answers

Crown victoria window motor replacement


remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Jul 21, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
2001 Chrysler PT Cruiser Logo

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...