Question about 2000 Kia Sportage

1 Answer

4wd not working after i shift - 2000 Kia Sportage

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Kia Expert
  • 146 Answers

The hubs are vacuum actuated you might have a bad seal, line or low vacuum.

Posted on Nov 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

2 Answers

I have a 93 jeep Cherokee, it will move in 4wh and in 4wl but will not go back into 2wd?


Hello guy
try posting what 4wd system you have,? first.
command trac or select track, (the latter is full time)
part time or the full time system,
we cant guess it....
read the operators guide first, if a part time system only
as i suspect, stop driving on dry pavement.
it's only for ice, or dirt. part time. part time is not a full time system.
Command-Trac
shifting to 4wd on dry (means no ice) pavement causes, drive line wind up! and the gears to lockup. (see steering get tight in turns?> and is dangerous to drive it like this , you, me and the box)
posted here 100s of times.

http://www.rubicon-trail.com/4WD101/driveline-bind.html


the non grand Cherokee. early

had these choices
  • 1987-2001: New Process NP231 Command-Trac, part-time only, 2.72:1 ratio with low range
NP231 has the following settings: 2HI, 4HI, N, 4LO
  • 1987-2001: New Process NP242 Selec-Trac, full-time or part-time, 2.72:1 ratio with low range
NP242 has the following settings: 2HI, 4 full-time, 4 part-time, N, 4LO


as you can see you need to first know, what NP box you have or
photo your shift lever for 4wd, an post it and we tell you.

more facts, on select trac. (totally unlike command trac)
Selec-Trac locking hub is used on 4WD Cherokee. Selec-Trac
utilizes a non-disconnect front axle. Engagement of 2WD or 4WD is
accomplished at transfer case by means of mechanical shift linkage.
System allows full or part time 4WD. Selec-Trac can be shifted into
2WD or 4WD modes from inside the vehicle at any speed.
unquote
next from the service manual,
4WD TO 2WD
1) Place mode select switch in 2WD position. Transfer case
should shift to 2WD and not allow shifting into 4WD or LO range. Axle
should shift after transfer case shifts.
2) To determine if front axle has completed a shift out of
4WD into 2WD, position mode select switch back to 4WD position while
operating vehicle at slow speed. If vehicle shifts into 2WD, axle will
ratchet. If shift is not completed, transfer case will shift into 4WD
and hissing sound will come from mode select switch.
end quote.

if unsure read the FSM book its free.
shows you both systems and how to diagnose it.

in the box, click Cherokee,,then click 1993, and behold.
the real deal.

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

4e7ebed4-9c81-4927-b26e-02808a82acff.jpg

May 10, 2016 | Jeep Cars & Trucks

1 Answer

2005 blazer won't shift out of 4WD


put in reverse get going 5-10 mph put in neutral then try to get out of FWD while still in motion.This doesn't always work but it eliminates
a lot of possibilities.

Mar 10, 2013 | Cars & Trucks

1 Answer

Can some explain the proper way to shift from 2wd


4wd auto: you can shift into this mode at anytime. it is good for conditions where you might need 4wd.
4wdhi:: you can shift into this at speeds up to 30mph and both of these back to 2wd while in gear.
4wd lo : stop vehicle and shift truck into nuetral ok to be rolling around 3mph shift into 4lo then put in gear same when shifting back to 2wd

Feb 19, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

My 4x4 is stuck in four wheel low it is shift on the fly and i have already replaced the transfer case motor


Ok here is a long shot but sometimes it will work. Put the 4wd position switch to 4wd Lo, put your transmission in reverse and back up for about 50 yards, stop and put your transmission in neutral, then shift the 4wd to 4wd hi, wait a few seconds and shift the 4wd to 2wd hi, Sometimes the t-case will get stuck and this is how you reset the computer. I have known people that really got their t-cases messed up because they thought that shift on the go meant that they could shift the t-case into 4wd LO while moving but shift on the go is only for 4wd hi the gears will not mesh up fast enough for 4wd LO because the ratio is 1 to 1 . I hope this helps you.

Feb 08, 2010 | 1990 Ford Bronco

1 Answer

1996 ford explorer 4wheel drive will not engage into the hubs need to know how it works


make sure your 4WD switch is working.and fuse is okay.because your 4WD is control by 4 electric shift motors in which drive a rotary cam which moves the mode fork and range fork inside the transfer case to select between 2WD HIGH A4WD - 4WD HIGH AND 4WD LOW RANGE.a shift motor sensing plate on the shift motor monitors the range in which the transfer case is operating a transmission range sensor monitors the gear position of the transmission.which must be in neutral to shift into low.a pair of solenoids one for 2WD one for 4WD.mounted on the upper right firewall route vacuum to the vacuum motor which engages and disengages the center axle disconnect collar in the front axle assembly.a 4 x 4 shift motor relay module contains two GEM controlled relays which shift the transfer case shift motor between 2WD and 4WD modes.a solid state clutch relay activates the A4WDclutch inside the transfer case.

Dec 13, 2009 | 1996 Ford Explorer

1 Answer

Electric 4WD selector switch on dash does not select/deselect 4WD. I wish to manually shift the selector at the gearbox if this is possible.


by swapping vaccum hoses on front diff shift on fly unit you can get out of 4wd or vise versa or by removing and sliding sleeve ring inside diff tube over, check range selection detent switch on this unit it is a on/off switch.these fail often

May 27, 2009 | 1995 Isuzu Pickup

1 Answer

I press the button but truck won't shift into 4WD


That sounds like a serious problem with the guts inside of the transfer case. Or it could be as simple as the shifter motor not working correctly. Take the motor off and see if it turns correctly when you press the buttons. Also, leave a comment telling what the lights say.

Dec 22, 2008 | 2003 Toyota Tacoma

4 Answers

My 98 chevy blazer won't shift into 4wd.


Had the same problem, disconnected the battery for about fifteen minutes, reconnected, 4 wheel drive hi and lo work like a charm now.

Dec 14, 2008 | 1998 Chevrolet Blazer

2 Answers

Will not shift into 4wd low but will shift into 4wd high


it sounds like a transfer case problem in this case will have to get inspected

Jun 30, 2008 | 2007 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
2000 Kia Sportage Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...