Question about Infiniti Cars & Trucks

Open Question

Infiniti fx35 windshield reservoir pump removal photos

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Windshield washer fluid will not pump

the windshield washer pump might be bad. It should be located somewhere on the reservoir

Posted on Nov 27, 2008

  • 1 Answer

SOURCE: where do i find the engine number of an infiniti FX35

plese show engin where r engin no i have vehcalev8 4.7 2004

Posted on Jan 24, 2009

  • 1075 Answers

SOURCE: how do you replace the battery on a 2005 infiniti fx35

i need more information?

Posted on Feb 18, 2009

  • 16 Answers

SOURCE: Removing the windshield washer reservoir in a 2002 Chrysler T&C

REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the engine fresh air housing inside the engine compartment.
  3. Disconnect the washer hose at the in-line connector forward of the cowl grille so that the in-line connector remains with the washer hose from the fresh air plenum.
  4. Disconnect the washer hose from the hose clip located on the front fender side shield.
  5. Remove the filler tube screw.
  6. Hoist and support vehicle on hoist or jack stands.
  7. Remove the right front wheel and tire assembly.
  8. Disconnect the left right front wheelhouse splash shield and move aside.
  9. Drain washer fluid from the reservoir and into a suitable clean container. This can be done by disconnecting the windshield washer hose from the front (outboard) washer pump and allowing the washer fluid to drain into a container through a temporary jumper hose connected to the front washer pump.
  10. Disconnect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the release position, then, depress the black tab and pull the connector off the pump or sensor.
  11. Remove the two reservoir mounting screws.
  12. Disconnect the reservoir from the body mount by raising the reservoir upward slightly and then down so that the reservoir filler neck and front washer hose pull through the opening in the front fender side shield.
INSTALLATION

  1. Push filler neck and front washer hose through the opening in the front fender side shield. Connect the reservoir to the body mount by lowering the reservoir down.
  2. Install the two reservoir mounting screws. Torque screws to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  3. Connect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the closed or locked position.
  4. Assure that washer is properly routed to prevent pinching and possible inoperative washers.
  5. Connect the left right front wheelhouse splash shield and move aside.
  6. Install the right front wheel and tire assembly.
  7. lower vehicle from hoist or jack stands.
  8. Install the filler tube screw. Torque screw to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  9. Connect the washer hose to the hose clip located on the front fender side shield.
  10. Connect the washer hose at the in-line connector forward of the cowl grille.
  11. Install the engine fresh air housing inside the engine compartment.
  12. Connect the battery negative cable.
  13. Verify system operation.

Posted on Apr 01, 2009

  • 7 Answers

SOURCE: wanting to activate XM radio in my 2005 infiniti fx35

1st you will need to contact Infiniti, so they can quote you the option which is $700.00 something dollars when i checked. Just because its equipped there are still things that need to be added in order to make it function. As per the mechanic. Rip off.

Posted on May 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out


The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.

Apr 07, 2015 | Ford Cars & Trucks

1 Answer

P1446 infiniti FX35


for your infiniti FX35,
P1446 - Infiniti Type Powertrain - Manufacturer Controlled DTC - Manufacturer Controlled Description Evaporative emission (EVAP) canister purge control valve - malfunction
Cause Wiring, EVAP valve, mechanical fault, ECM

or you can ask the 24 hrs live technical support http://www.spobd2.com/service/, they will like to help you, good luck

Jul 06, 2013 | Infiniti Cars & Trucks

1 Answer

Wheres the water pump


Hi there,

If your engine is the VQ35, then your water pump is located inside the engine cover.

Replacing the water pump is not a straight forward job, as it requires the removal of many external components (i.e. air ducts, grills, covers, belts, reservoirs etc) and internal components such as idler pulley, cranshaft pulley, tensioner etc. The coolant will need to be drained also.

CAUTION: do not spill coolant on the drive belts.

As per diagram, with engine cover removed the water pump (item # 1) can be found after removing the water pump cover (item # 5).

1_13_2012_1_10_55_am.jpg

Unless you have access to the Factory Service Manual, I strongly advise you entrust this job to an Nissan agent who has experience in replacing a water pump on this model.

Note: allowing a non-experienced mechanic to perform this work, could result in unnecessary labor time and more cost to you, so you should take this into consideration when weighing up the costs.


Hope this answers your question.


"Please rate this solution"

Dec 28, 2011 | 2006 Infiniti FX35

1 Answer

Our fx35 over heated and refuse to start


Hi.

If the car overheated you may have blown the head gasket and other in the block. In that case the engine may not start anymore because of lack of compression, because piston rings are gone, valves may have been damaged etc. Another part that in many vehicles may blow with engine surge from overheating is the fuel pump. There are more parts that must be tested. If overheating drained the coolant fluid reservoir, then the head gasket usually must be replaced. Try replacing the spark plugs. If there have been overheating and engine surging the spark plugs must be replaced. If that does not do the job, then there is a major fault to troubleshoot.

Regards.

Ginko

Sep 19, 2011 | 2006 Infiniti FX35

1 Answer

Removing rear brake rotors


remove rear brake rotors on 2005 infiniti fx35

May 01, 2010 | 2005 Infiniti FX35

1 Answer

'04 Infiniti FX35 back driver side window does not open or close.


need to pull door panel off there is a cable that op. the window they get twisted in motor poss. need window motor..

Feb 20, 2010 | 2004 Infiniti FX35

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Wash wipe on a Focus 2000 model


I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...