Question about 2001 Isuzu Rodeo

1 Answer

I have a 01 rodeo, replaced timing belt because it was time to change it. however, the marks are right, but it will not rev up and has no power. checked the timing marks and they are correct. someone told me that the computer had to be reset, but how do i do this? thanks, Bill

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 44,428 Answers

I would be running the fault codes to check for faulty sensors. To reset the CPU use a code reader but I suspect that will not be your problem

Posted on Oct 14, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: trouble getting marks aligned on 2001 Izusu Rodeo

if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Posted on Jul 30, 2009

honeymokey
  • 3113 Answers

SOURCE: won't start after timing belt has been replaced

The cam pulleys turn 3 or more turns to one of the camshaft. You need to find someone that is experienced on this vehicle. Just aligning marks does not mean its in sync.

Posted on May 13, 2009

  • 31 Answers

SOURCE: 2001 isuzu rodeo v6 3.2

Go to parts store get manual that will tell you a lot better then it can be explained

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 1999 Isuzu Rodeo 3.2 V6 DOHC If you put all timing marks together on engine and then put timing belt mark all together on the engine and rotate two rounds with crankshaft does all the marks come


Just the engine. The marks on the belt are to make sure the teeth are in the right place when replacing. It might come back in place on 4 turns of the crankshaft. I have never checked to see if the belt marks came back. But always check the timing marks themselves.

Hope this helps.

Nov 10, 2014 | 1999 Isuzu Rodeo

1 Answer

Have a 01 rodeo 3.2 v6. replaced timing belt but will not rev up. double checked the marks and they are right, but still will not run right. someone told me that the computer had to be reset. how is...


to reset computer, disconnect battery for at least 10 mins reconnect battery, drive car for a couple of days until it relearns how to operate engine correctly.

Oct 14, 2013 | 1998 Isuzu Rodeo

1 Answer

Just had 90,000 km service done - mech replaced - timing belt/belt timing balance/alt belt and drive belt. Car runs like its a deisel and has a vibration and revs go grinding when at 2700 revs. Is there...


It does sound like they didn't get the timing right. If it ran good before then it should not have changed when they did the work. Don't let them give a line like something else broke. Make them fix it.

Aug 30, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

I have a Isuzu rodeo 1994 3.1 in I can't find the


The timing marks are stamped into the head and in the cam pulley, also on the crank and the case, find them and paint them white so you can see them, the new belts have the marks on the belt, they will line up, If they don't , you got it wrong, You can do this without spinning the cams or crank and losing the marks, as long as the belt marks line up, you will be all set. Put the pin in the tensioner before removing the belt. Did you change the water pump? And I think the engine is 3.2L. Get it in there and pull the pin, It should be right on. Turn over the engine by hand a couple times to make sure it comes around on the marks. If it is wrong, it will go about 11 or 12 miles, and you will need a new engine. Hope this helps.

Jun 04, 2011 | 1994 Isuzu Rodeo

1 Answer

How to change the water pump? what has to come off first,second third etc.


I have a 1997 Rodeo so I'm not sure it is the same, but if your waterpump is located under the timing belt cover like mine is and is driven by the timing belt ...

1) Remove the upper fan shroud
2) Remove the (4) nuts then the cooling fan assembly
3) Remove the power steering drive belt
4) Remove the air conditioning compressor drive belt
5) Remove the generator drive belt
6) Remove the fan pulley assembly
7) Remove the crankshaft pulley
8) Remove the oil cooler hose
9) Remove the timing belt cover
10) Remove the timing belt pusher
11) Mark where the timing belt is currently seated in the cam and crankshaft gears (be real sure you know what you are doing here!!!)
12) Remove the timing belt
13) Drain the radiator
14) Remove the waterpump

Mar 01, 2011 | 1999 Isuzu Rodeo

1 Answer

I am replacing my timing belt and tensioners on my 1994 rodeo, when I removed the timing belt the right side cam sproket moved clock wise, I need to set the timing and do not have the steps the manuel does...


You were supposed to clamp the cams so they don't spin, not to worry, I think they will only go so far, your belt should have marks on it, If it doesn't take it back and get one with marks on it, you need these to line up with the marks on the cams and crank, if they don't line up, I'll give your engine 11 miles before that cams shatter. When all three are in line, you should be all set, pull the pin on the belt tensioner and let her rip, don't forget the water pump, you got in there, do it .

Dec 12, 2009 | 1994 Isuzu Rodeo

1 Answer

I need a new timming belt on a 01 kia sephia how do i change it


Hi there,

Below are the procedures to remove the timing belt...

1. Disconnect negative battery cable.

fd440e5.jpg
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt.

1d207cf.jpg

4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts.


077a275.jpg

6. Remove water pump pulley.

2bc0452.jpg


7. Remove crankshaft pulley and timing belt guide plate.



8619b52.jpg


8. Remove upper and lower timing belt covers.


c250533.jpg


9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.


213d3a1.jpg




10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned with mark on cylinder head cover.


Do not move camshaft or crankshaft once timing marks have been correctly positioned.



a3188ba.jpg



11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.


12101a7.jpg

14. Remove timing belt.



Regards,
Jeep Brainy

Sep 20, 2009 | 2001 Kia Sephia

1 Answer

Trouble getting marks aligned on 2001 Izusu Rodeo


if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Jul 29, 2009 | 2002 Isuzu Rodeo

1 Answer

I need the timing to motor 3.2 .


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the air cleaner assembly and intake air duct.
  4. Remove the upper fan shroud from the radiator.
  5. Remove the 4 nuts retaining the cooling fan assembly. Remove the cooling fan from the fan pulley.
  6. Loosen and remove the drive belts.
  7. Remove the upper timing belt covers.
  8. Remove the fan pulley assembly.
  9. Rotate the crankshaft to align the camshaft timing marks with the pointer dots on the back covers. Verify that the pointer on the crankshaft aligns with the mark on the lower timing cover.
    NOTE When the timing marks are aligned, the No. 2 piston is at Top Dead Center (TDC) compression.

    WARNING Align the camshaft and crankshaft sprockets with their alignment marks before removing the timing belt. Failure to align the belt and sprocket marks may result in valve damage.
  10. Use tool No. J-8614-01, or a suitable pulley holding tool to remove the crankshaft pulley center bolt. Remove the crankshaft pulley.
  11. If present, disconnect the 2 oil cooler hose bracket bolts on the timing cover. Move the oil cooler hoses and bracket off of the lower timing cover.
  12. Remove the lower timing belt cover.
  13. Remove the pusher assembly (tensioner) from below the belt tensioner pulley. The pusher rod must always face upward to prevent oil leakage. Depress the pusher rod, and insert a wire pin into the hole to keep the pusher rod retracted.
  14. Remove the timing belt.
  15. Inspect the water pump and replace it if there is any doubt about its condition.
  16. Repair any oil or coolant leaks before installing a new timing belt. If the timing belt has been contaminated with oil or coolant, or is damaged, it must be replaced.

    0900c1528002abd0.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using a double clip to hold the belt in place-3.2L and 3.5L engines


    0900c1528002abd1.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. For maximum timing belt life, install the belt as shown-3.2L and 3.5L engines


    0900c1528002abd2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of timing belt tensioner and pusher-3.2L and 3.5L engines


    0900c1528002abd3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Timing mark alignment and timing belt routing-3.2L and 3.5L engines


    0900c1528002abd4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of timing belt tensioner pusher-3.2L and 3.5L engines

To install:
  1. Verify that the sprocket timing marks are still aligned and that the groove and the keyway on the crankshaft timing sprocket align with the mark on the oil pump. The white pointers on the camshaft timing sprockets should align with the dots on the front plate.
  2. Install the timing belt. Use clips to secure the belt onto each sprocket until the installation is complete. Align the dotted marks on the timing belt with the timing mark opposite the groove on the crankshaft sprocket.
    NOTE The arrows on the timing belt must follow the belt-s direction of rotation. The manufacturer-s trademark on the belt-s spine should be readable left-to-right when the belt is installe

Jul 10, 2009 | 1995 Isuzu Rodeo

2 Answers

Won't start after timing belt has been replaced


The cam pulleys turn 3 or more turns to one of the camshaft. You need to find someone that is experienced on this vehicle. Just aligning marks does not mean its in sync.

May 08, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...