Question about 1998 Isuzu Rodeo

1 Answer

Have a 01 rodeo 3.2 v6. replaced timing belt but will not rev up. double checked the marks and they are right, but still will not run right. someone told me that the computer had to be reset. how is this done? thanks, Bill

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 635 Answers

To reset computer, disconnect battery for at least 10 mins reconnect battery, drive car for a couple of days until it relearns how to operate engine correctly.

Posted on Oct 14, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
honeymokey
  • 3113 Answers

SOURCE: won't start after timing belt has been replaced

The cam pulleys turn 3 or more turns to one of the camshaft. You need to find someone that is experienced on this vehicle. Just aligning marks does not mean its in sync.

Posted on May 13, 2009

stevenhurc
  • 450 Answers

SOURCE: trouble getting marks aligned on 2001 Izusu Rodeo

if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Posted on Jul 30, 2009

  • 31 Answers

SOURCE: 2001 isuzu rodeo v6 3.2

Go to parts store get manual that will tell you a lot better then it can be explained

Posted on Nov 02, 2009

  • 270 Answers

SOURCE: I would like a diagram of a V6 timing belt

In the US the public library should have an auto repair data base that you can access with your library card number. If not you could always go there and check out a real book.

Posted on Dec 24, 2009

bigguy810
  • 448 Answers

SOURCE: 01 rodeo 3.2 v6 surpentine

try looking on top of the radiator that cover shooed have it on there

Posted on Apr 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the timing belt give the diagram 2001 Isuzu rodeo v6 jeep


it's no jeep,. sorry.
Rodeo run 3 or 4 v6 engines.
so what is the displacment and best is to say what country,.
are you in canada?
we are a USA forum., so...??
the fsm book covers this.
as does alldata.com
Isuzu is dead here in uSA, so they cant sell you a book.

in usa its a Gen 2 Rodeo
here are the 32 v6s in gen2
most common here is the 6vd1 in usa. alldata.com covers ours.
so lets google that.
using real names for engines makes google search HIT.
true for all cars. all engines.
so i type for you, and bingo, hits a many. even a video. hark.

https://www.google.com/webhp?gws_rd=ssl#q=isuzu++6vd1+timing+belt

Mar 04, 2015 | 2001 Isuzu Rodeo

1 Answer

On a 1999 Isuzu Rodeo 3.2 V6 DOHC If you put all timing marks together on engine and then put timing belt mark all together on the engine and rotate two rounds with crankshaft does all the marks come


Just the engine. The marks on the belt are to make sure the teeth are in the right place when replacing. It might come back in place on 4 turns of the crankshaft. I have never checked to see if the belt marks came back. But always check the timing marks themselves.

Hope this helps.

Nov 10, 2014 | 1999 Isuzu Rodeo

1 Answer

I have a 01 rodeo, replaced timing belt because it was time to change it. however, the marks are right, but it will not rev up and has no power. checked the timing marks and they are correct. someone...


I would be running the fault codes to check for faulty sensors. To reset the CPU use a code reader but I suspect that will not be your problem

Oct 14, 2013 | 2001 Isuzu Rodeo

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

1 Answer

2001 isuzu rodeo v6 3.2 Need Timing belt replacement procedure. Timing mark alignment positions.


Go to parts store get manual that will tell you a lot better then it can be explained

Oct 21, 2009 | 2001 Isuzu Rodeo

1 Answer

Trouble getting marks aligned on 2001 Izusu Rodeo


if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Jul 29, 2009 | 2002 Isuzu Rodeo

2 Answers

Won't start after timing belt has been replaced


The cam pulleys turn 3 or more turns to one of the camshaft. You need to find someone that is experienced on this vehicle. Just aligning marks does not mean its in sync.

May 08, 2009 | 2000 Isuzu Rodeo

3 Answers

Isuzu rodeo leaking coolant from engine


with my experiance on these engines it's usually the upper outlet hoses running from the heads into a t then into the upper radiator hose they are pain to replace but 3 out of 3 of my v6 isuzu's have had the same problem you'll have to pull off the theromstat and the coil pack the hoses are very small and run from the end of the heads one on each into a t then into the radiator hose just under the housing

Apr 27, 2009 | Isuzu Rodeo Cars & Trucks

2 Answers

Is my '99 Isuzu Rodeo a single OR a dual cam? How can I find out?


HI.....
1999 Isuzo Rodeo. 3.5 L or 3.2L V6. Is a DOHC. Double over head cam.
and the engine 2.2 L 4cyl. SOHC, single over head cam.
The angibe 2.3 L 4cyl. Is DOHC.

OK.. I hope this help on your question.

Thank you for use fixya...

Aug 07, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...