Question about Cars & Trucks

Open Question

Rjp63k2 equivalent - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front wheelbearing


read the fsm
read alldata.com>?/
read how on toyota nation dot com.. free, car is a toyota corolla.


quote FSM
  1. Raise and safely support the vehicle. Remove the wheel.
  2. Disconnect the ABS speed sensor, if equipped.
  3. Remove the halfshaft nut.
  4. Remove the brake caliper and support it out of the way .Remove the disc brake rotor.
  5. Separate the tie rod end from the knuckle.
  6. Separate the ball joint from the knuckle.
  7. Remove the 2 nuts and bolts securing the steering knuckle to the strut.
  8. Remove the steering knuckle and hub assembly.
  9. Clamp the knuckle in a vise with protected jaws.
  10. Remove the dust deflector.
  11. Use a slide hammer and extractor tool J-26941 or equivalent, to remove the inner oil seal.
  12. Remove the snapring.
  13. Using hub puller tools J-25287 and J-35378 or equivalents, remove the hub from the knuckle. (use any slam hammer)
  14. Remove the brake splash shield.
  15. Using a split plate bearing remover, puller pilot and a shop press, remove the inside and outside inner bearing races from the hub.
  16. Remove the outer oil seal.
  17. Position the steering knuckle on support tool J-35379 or equivalent. Remove the bearing from the knuckle using a plastic hammer and remover tool J-35399 or equivalent, and driver handle J-8092 or equivalent.

Jun 14, 2014 | 1996 Geo Prizm

1 Answer

Wheel barings replace


my guess , your first time?
if first time, dont. no really, but do use real jack stands. got them?
but if must? with no safety training. ?????
then
RTM.
it's all here.
alldata dot com.

there are 17 steps, (off)]
here they are (pasted)_
  1. Raise and safely support the vehicle. Remove the wheel.
  2. Disconnect the ABS speed sensor, if equipped.
  3. Remove the halfshaft nut.
  4. Remove the brake caliper and support it out of the way .Remove the disc brake rotor.
  5. Separate the tie rod end from the knuckle.
  6. Separate the ball joint from the knuckle.
  7. Remove the 2 nuts and bolts securing the steering knuckle to the strut.
  8. Remove the steering knuckle and hub assembly.
  9. Clamp the knuckle in a vise with protected jaws.
  10. Remove the dust deflector.
  11. Use a slide hammer and extractor tool J-26941 or equivalent, to remove the inner oil seal.
  12. Remove the snapring.
  13. Using hub puller tools J-25287 and J-35378 or equivalents, remove the hub from the knuckle.
  14. Remove the brake splash shield.
  15. Using a split plate bearing remover, puller pilot and a shop press, remove the inside and outside inner bearing races from the hub.
  16. Remove the outer oil seal.
  17. Position the steering knuckle on support tool J-35379 or equivalent. Remove the bearing from the knuckle using a plastic hammer and remover tool J-35399 or equivalent, and driver handle J-8092 or equivalent.
end off , see manual for install.

Dec 19, 2012 | 1995 Geo Prizm

1 Answer

Spark plug gap for 1996 jeep cherokee


Thread Grand Cherokke, but ask about Cherokee ???

Make: JEEP
Model: GRAND CHEROKEE - LIMITED
Year: 1996
Engine: V8 - 5.2L - FI - - GAS
Part Number RC12YC
GAP .035" (Original Equipment Manufacturer and/or Original Equipment Equivalent)

Engine: L6 - 4.0L - FI - - GAS
Part Number RC12YC
GAP .035" (Original Equipment Manufacturer and/or Original Equipment Equivalent)


Make:
JEEP
Model: CHEROKEE
Year: 1996
Engine: L6 - 4.0L - FI - - GAS
Part Number RC12LYC
GAP .035" (Original Equipment Manufacturer and/or Original Equipment Equivalent)


Hope this helps (remember to rate this free answer ans leave some testimonial).

Sep 27, 2011 | 1997 Jeep Grand Cherokee

4 Answers

I need to buy some power steering fluid for my 2002 Cadillac diville where and what kind do i buy


gmlogoflat.gif Service Information bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2002 Cadillac DeVille ' DeVille VIN K Service Manual ' General Information ' Maintenance and Lubrication ' Specifications ' Document ID: 792664 Fluid and Lubricant Recommendations Application
Fluid/Lubricant
Automatic Transaxle
DEXRON®-III Automatic Transmission Fluid
Chassis Lubricant
Chassis lubricant GM P/N 12377985 or equivalent lubricant meeting requirements of NLGI # 2, Category LB or GC-LB
Engine Coolant
50/50 mixture of clean, drinkable water and GM Goodwrench® DEX-COOL® or Havoline® DEX-COOL® Coolant
Engine Oil
Engine oil with the American Petroleum Institute Certified for Gasoline Engines "Starburst" symbol of the proper viscosity. To determine the preferred oil viscosity for the engine of this vehicle, refer to Explanation of Scheduled Services
Hinges, Hood and Door
Multi-Purpose Lubricant, Superlube® GM P/N 12346241 or (Canadian P/N 10953474) or equivalent
Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor and Release Pawl
Lubriplate®Lubricant Aerosol GM P/N 12346293 or (Canadian P/N 992723) or equivalent lubricant meeting requirements of NLGI # 2, Category LB or GC-LB
Hydraulic Brake System
Delco Supreme 11®Brake Fluid GM P/N 12377967 or (Canadian P/N 992667) or equivalent DOT-3 Brake Fluid
Key Lock Cylinders
Multi-Purpose Lubricant, Superlube® GM P/N 12346241 or (Canadian P/N 10953474) or equivalent
Parking Brake Cable Guides
Chassis Lubricant GM P/N 12377985 or equivalent lubricant meeting requirements of NLGI # 2, Category LB or GC-LB
Power Steering System
GM Power Steering Fluid GM P/N 1052884 or (Canadian P/N 993294) or 1050017 or (Canadian P/N 992646) or equivalent
Weatherstrip Conditioning
Dielectric Silicone Grease GM P/N 12345579 or (Canadian P/N 1974984) or equivalent
Windshield Washer Solvent
GM Optikleen® Washer Solvent GM P/N 1051515 or (Canadian P/N 993033) or equivalent

i would just stop by your local dealer for the correct fluid. part number is listed.

Jul 29, 2011 | 2002 Cadillac Deville

2 Answers

Can some one please tell me if there is a certain spark plug that needs to be put in my 2000 beetle 2.0 motor or will any work.


You need to use an NGK 7092 Spark plug or equivalent. Note this is a NAPA part number & may not work everywhere.
So to answer your question, No you can't use just any plug.

Jan 17, 2011 | 2000 Volkswagen Beetle

2 Answers

Where is the oil pressure sending unit on a 2005 4X4 Suburban 1500 5.3 liter


Removal & Installation 4.8L, 5.3L & 6.0L Engine To Remove:
  1. Remove the engine sight shield. chevy_aval15_02-04_opcon.gif

  2. Disconnect the oil pressure sensor electrical connector. chevy_aval15_02-04_opsocket.gif

  3. Using J41712 sensor socket or equivalent, remove the oil pressure sensor.
To Install:
  1. Apply sealant GM P/N 12346004, (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J41712 sensor socket or equivalent, install the oil pressure sensor. Tighten the sensor to 15 ft. lbs. (20 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.
8.1L Engine To Remove:
  1. Remove the engine appearance cover.
  2. Disconnect the electrical connector from the oil pressure sensor.
  3. Use a special socket such as J 41712 to remove the sensor.
To Install:
  1. If installing the old sensor, apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J 41712 or equivalent, install the sensor. Tighten the sensor to 22 lb ft (30 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine appearance cover.
prev.gif next.gif

Aug 05, 2010 | 2004 Chevrolet Suburban

1 Answer

Instructions to change oil pressure switch GMC denali xl


4.8L, 5.3L, 6.0L & 6.2L Engines
  1. If necessary, remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.

    0996b43f802053c2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using J 41712 or equivalent, remove the oil pressure sensor

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    1. Tighten the oil pressure sensor to 26 ft. lbs. (35 Nm).

  3. Connect the oil pressure sensor electrical connector.
  4. If necessary, install the engine sight shield.


Jan 18, 2010 | 2004 Chevrolet Suburban

1 Answer

The oil sensor needs to be replaced where is it


  1. Remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.

    0996b43f802053c4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using J 41712 or equivalent, remove the oil pressure sensor-8.1L engines

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    1. Tighten the sensor to 22 ft. lbs. (30 Nm).

  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.

Nov 15, 2009 | 2001 Chevrolet Silverado 2500HD

1 Answer

Remove/replace shock absorber assembly 900s 1995 saab


  1. Slightly loosen hub center nut when all four wheels are on ground.
  2. Raise and support vehicle, then remove five wheel bolts and wheel.
  3. Remove hub center nut, then the wheel sensor,
  4. Press back brake piston using slip-joint pliers,
  5. Remove caliper from steering swivel member, then suspend in wheel housing with cable tie.
  6. Remove brake disc and back plate, then slightly loosen tie rod end nut.
  7. Press out tie rod end nut using puller tool or equivalent.
  8. Remove nut and tie rod end bolt, then the anti-roll bar to swinging arm nut.
  9. Remove outer ball joint nut.
  10. Press ball joint out of steering swivel member using puller tool or equivalent, installed on spring link.
  11. Remove nut and discard. This self-locking nut must not be reused.
  12. Remove three upper mounting nuts for MacPherson strut, then the strut.
  13. Clamp MacPherson strut in vice.
  14. Compress spring using spring compressor or equivalents.
  15. Hold piston rod and remove nut using MacPherson strut socket tool 89 96 662, or equivalent. This is a self-locking nut and must not be reused.
  16. Remove mounting and top spring seat, then the coil spring, gaiter and compression stop.
  17. Unscrew damper using wrench tool No. 89 96 670, or equivalent, then remove damper from strut.
  18. Reverse procedure to install, noting the following:
    1. Screw damper in place using wrench tool No. 89 96 670, or equivalent.
    2. Lower end of coil spring should abut against stop in bottom of spring cup.
    3. Position MacPherson strut on vehicle and install three retaining nuts on top mounting. Tighten nuts alternately, according to specifications.
    4. Always use new hub center nut with self-locking threads.

Jun 04, 2009 | 1995 Saab 900

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...