Question about Cars & Trucks

Open Question

87 cr80 keeps pushing right crank seal out which results in gear oil going into cylinder!

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 57 Answers

SOURCE: replace oil seal

no need for a diagram. Just remove the driveshaft and pull the seal out. Go to your local autoparts store (or Sears) and buy a seal puller. They are cheap. While at the autoparts store you could wander over to the Haynes auto manual section and flip through to see exactly how they say to do it (if they have a book unsealed). It's easy, just dig in. You may have to take the tailshaft housing off but that is only a a few bolts. That would make it easier but I've done it without removing it... also, if it's leaking, check the tailshaft housing for cracks. They are known for hairline cracks which equalls leaks. You may have to remove the housing anyway. Good luck!

Posted on May 14, 2008

Ad
  • 1 Answer

SOURCE: oil leak problem with 1996 toyota camry

I am going to see a mechanic - my trusted mechanic who does not nickel and dime me - to see what this is. I have the same problem and he told me he has never done this job on a Camry and is unsure. Given the miles, he has suggested that maybe it is time to part ways with the car. I am going to ask him if he will put some florescent dye in it and let me drive it for 50-100 mi and then check to see where the leak is and fix it. Let you know what happens. I have to try, the car is solid.

Posted on Aug 15, 2009

arauzvictor1
  • 466 Answers

SOURCE: changed master cylinder after push rod snapped.

It verifies if the auxiliary cylinder opens completely if this one does not open it is because the principal cylinder has air

Posted on Dec 30, 2009

  • 43 Answers

SOURCE: my truck is a manual and it wont go into gear

It could be a bad clutch cylinder or a bad slave cylinder. If it is either - the clutch would not fully disengage. This would make changing gears very difficult. If it is the slave cylinder the system should loose fluid and start to drip if you pump it repeatedly. If it is the clucth cylinder it should just seep past the plunger seals and the fluid may not lower. If you put the truck in gear without starting it and push the clutch in - can you push the vehicle? If the answer is no - the clutch is not fully disengaged.

Posted on Jan 26, 2010

junk9
  • 150 Answers

SOURCE: 2000 go tracker bad oil

It has to be an oil pressure sending unit. There are two of them on that SUV but they are in different places depending on your engine cord. If you go to Advance Auto parts or O'Riley, they will tell you exactly where to look.

Posted on Nov 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEED DIAGRAM FOR LOCATIONS OF CRANKSHAFT PULLY,OIL SLINGER AND SPRING.FOR 1983 MAZDA 2.2L DIESEL


Here is the procedure:-


  1. Remove setscrew from side of cylinder block.


  2. Remove oil pipe attaching bolts.


  3. Remove oil pump and strainer.
TIMING GEAR COVER



  1. Remove timing gear cover to case attaching bolts.


  2. Remove timing gear cover and gasket.

CAMSHAFT, CRANKSHAFT, IDLER & INJECTION PUMP GEARS



  1. Remove oil slinger and washers from crankshaft snout.
Using puller set 49 0839 425C or equivalent, remove crankshaft timing gear, Fig. 3.


  1. Position a clean rag between camshaft and idler gears, then remove cam gear lock bolt and washers.


  2. Using puller set 49 0839 425C or equivalent, remove cam gear from camshaft, Fig. 3.


  3. Remove idler gear to spindle retaining nuts and washers, then remove idler gear and spindle assemblies.


  4. Remove injection pump drive gear.


  5. Remove timing gear case to cylinder block attaching bolts, then the timing case.



CAMSHAFT




  1. Remove tappets from cylinder block.


  2. Remove camshaft thrust plate to cylinder block retaining bolts and washers, then pull camshaft from block.



PISTON & CONNECTING ROD




  1. Remove connecting rod bearing cap retaining nuts and bolts, then separate bearing cap from connecting rod.


  2. Using the wooden handle end of a hammer, push the piston and connecting rod assembly outward until piston rings clear cylinder bore. Remove piston and connecting rod assembly through top of cylinder block.


  3. To separate piston from connecting rod, remove piston pin retaining clips, then press pin from piston using a suitable driver.



CRANKSHAFT




  1. Remove rear oil seal cap retaining bolts, then the cap and seal.


  2. Remove main bearing cap to cylinder block retaining bolts, then the main bearing caps and thrust washers.


  3. Lift crankshaft from cylinder block.

Mar 26, 2015 | Mazda Cars & Trucks

1 Answer

87 toyota clutch wont engage after brakes were replaced


Brake and clutch are vacumme assisted and hard to start seems like vac hose left of of has leak

Nov 14, 2012 | Toyota Cars & Trucks

3 Answers

Oil leak 2000 alero, just replaced plug, not it, leaked out all the oil after I drove it 20 miles, please help, could it be a gasket or what


Check the oil filter. The old gasket might be stuck on the engine (two gaskets stuck together), or the new gasket might be defective, misaligned or missing.

Nov 05, 2011 | 2000 Oldsmobile Alero

1 Answer

2002 grand am does not leak after driving, but I wake up in the morning to a huge puddle of oil.


SOUND LIKE FRONT CRANKSHAFT TIMING COVER SEAL OR REAR MAIN OIL SEAL LEAKING START ENGINE LET IT IDLE SEE IF YOU SEE OIL DRIPPING UNDERNEATH CAR LOOK FOR OIL LEAK AT TIMING COVER OR AT REAR OF ENGINE WHERE REAR MAIN SEAL LOCATED. CHECK ON TOP OF ENGINE INTAKE MANIFOLD AREA WHERE OIL PUMP DRIVE GEAR IS.O - RING AT THE OIL PUMP DRIVE GEAR WILL CAUSE LARGE OIL LEAK.OIL PUMP DRIVE GEAR IS LOCATED WHERE THE DISTRIBUTOR USE TO BE LOCATED.KEEP EYE ON OIL LEVEL IN CRANK CASE.KEEP PLENTY ENGINE OIL ON HAND UNTIL YOU FIX.I WOULD FIND LOCATE PROBLEM QUICK AS POSSIBLE BECAUSE OIL LEVEL GET TOO LOW ENGINE WILL SEIZE UP LACK OF OIL..

Jul 04, 2011 | 2001 Pontiac Grand Am SE

1 Answer

How to replace a oil pump on a 2005 nissan xterra


Working on 3.3Liter V6 Nissan Xterra, -Ok Take Neg Cable Off Battery,- Set motor to TDC Compression #1 #1 is front right Cylinder, -Remove Timing Belt, -Remove your timing belt tensior pulley, -Ok The Crankshaft Timing Sprocket take and remove outer spacer ring now take spray wd40 ect..behind gear try to get wd40 work between crank and gear i take hammer and gently knock the great back into the pump then i take crow feet and work the gear forward between the oil pump and the rear spacer ring then spray with wd40 and repeat process now if the lip of the spacer rings bends forward take straighten with vice and hammer, -Now time to drain Motor Oil,- Now Go to your right front Frame and remove 3 19mm head nuts off 19mm bolts from Idler Arm, push tires together Toe In, Watch your center link drop now you can began to remove your oil pan,Remove Starter, Remove the left bracket 14mm bolts and the right starter spacer Take Note: 14mm bolt just above the lowest starter bolt remove starter shim spacer, the 10mm bolts rear of oil pan 1/4 extiension and 1/4 10mm scoket -,The Motor mount 14mm nuts will have to be removed from the right mount almost all the way off your left drivers side mount, lift motor gently off right mount about 1 inch off the mount. Ok Remove Oil Pan From The Motor, Take Note 2 12mm head bolts right / left side of oil pump longest goes into alternator bracket, 4 10mm bolts 1 is hidden Lower right side Pump front now your oil pump will be loose to remove off pull forward to front of truck....I find that pouring Lucas engine oil stabalizer into the pump where oil filter mounts and turn pump until prime and take lithium grease and rub inside of front main crank seal..before installing new pump..!!! Take Note: if the crank sprocket gear is Stubborn I have seen Map Gas and i have seen holes drilled into front of gear, then Tapped and 2 bolt puller to remove the Sprocket but keep in mind your going to replace the pump so you can use a little force to get it to move just keep soaking with penatrating oil get it working back and forth....Hope this helps Oh yes Take Note: The converter Bolt Cover Will come out but the Engine - Transmission Spacer plate Will Stay in Place.I have seen tech take cutoff wheel and cut the engine Transmission Spacer Plate Where Starter Sits In And The left Side And Place it back into place where the bellhousing bolts hold it back in place but you should not have to do this..just thought it intersting...Dyi Nissan Xterra 3.3liter V6 Oil Pump R&R......

Jan 30, 2011 | 2005 Nissan Xterra

1 Answer

How to set the time belt?


4 Cylinder diesel(4JX1) :
1 - Timing mark
2 - Cam pulley
3 - HP Oil pump pulley
4 - Tensioner pulley


suzman_0.jpg

6 Cylinder petrol:
Align crank(C) timing notch mark (1) to oil pump mark.
Align cam pulley(L+R) marks(3) to cylinder head marks
The cam belt has 3 marks, 2 lines and one mark that is actually a row of dots. Align the dots to the crank pulley groove mark(2) and align the other 2 lines to the cam pulley marks. Using a clothes peg to hold the belt to the cam pulleys works wonders to keep it in place while fitting. Please note the arrows on the belt and have them point in the direction of rotation - right to left side of engine
W - water pump pulley
I - Idler pulley
T - Tensioner pulley.

If for some reason you need to realign the cams on each bank :
Standing in front of the car and starting from YOUR left , looking at the cams you should see RE, RI, LI, LE on each of the camshafts.(R for right bank, L for left bank, I for intake and E for exhaust) Right bank camshafts are marked with one dot, left bank with 2 dots on the shaft itself. To align the camshafts to each other each cam shaft gear has a mark on it. Draw an imaginary line between the centre of the camshaft and the centre of the pulley. The alignment mark should be between the two along this imaginary line. The result will be that RI an RE will be at the top of each gear. The same with the left bank.


suzman_2.jpg

Nov 08, 2010 | 1998 Isuzu Rodeo

1 Answer

Oil leak on a 87 caravan 3.0 V-6


Yes you can replace this in the car. You'll need to remove the front of the motor which includes the timing belt and harmonic balancer. The oil pump on the engine runs off of a gear pump from the crank. If the seal fails it will leak like the dickens. On a scale of 1-10 this jobs a 6 however with patients and the right tools you can have it done in six or so hours. Be certain to have engine properly timed on assembly. Go ahead and replace the timing belt and tensioner while you have it apart.

The attached may help you a bit. When you install the new lip seal use a piece of PVC pipe to make a tool to press the seal back in squarely.
http://www.aa1car.com/library/2003/us100344.htm

Please let me know if this helped,
Tom

Nov 02, 2009 | 1987 Dodge Caravan

1 Answer

Floods out 5 times out of 10 when trying to start car. Have to wait an hr. before trying to start again..Also a lose of power when going up a hill. Blue smoke comes out the exhaust. Also It won't change...


Blue smoke is caused by engine oil entering the cylinder area and being burned along with the fuel air mixture. As with the white smoke, just a small drop of oil leaking into the cylinder can produce blue smoke out the tailpipe. Blue smoke is more likely in older or higher mileage vehicles than newer cars with fewer miles. How did the engine oil get inside the cylinder in the first place? The car has many seals, gaskets, and O-rings that are designed to keep the engine oil from entering the cylinder, and one of them has failed. If too much oil leaks into the cylinder and fouls the spark plug, it will cause a misfire (engine miss) in that cylinder, and the spark plug will have to be replaced or cleaned of the oil. Using thicker weight engine oil or an oil additive designed to reduce oil leaks might help reduce the amount of oil leaking into the cylinder.

Jul 06, 2009 | 1991 Eagle Summit

1 Answer

1998 zx2 timing


timing mark is on flywheel for crank and on the rear end of the cams under the rocker cover.be carefull with this as the pulleys do not have keyways and can come loose resulting in smashed valves and piston.make sure retaining bols have locktite or better still araldite on the threads and use a impact gun on them.fairly easy job to do though,make sure you remove tensioner though and remove the dust cover and give a little drop of oil and some new grease then push seal cover back on ,saves the cost of a new bearing as these are not cheap.

Nov 09, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...