Question about Cars & Trucks

Open Question

2007 kubota rtv 900 transmission problem

2007 kubota rtv 900 transmission problem

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
hi99ins
  • 123 Answers

SOURCE: transmission gasket for 2007 HHR

When I replace transmission/oil pan gaskets,I never re-use the old gasket as a new one is cheap and a re-used one will usually leak as you have found.
The gasket that is supplied on most transmissions is a rubber type bound to each mating surface with a heat cured RTV. this bond once broken, is difficult to reinstate as the gasket and RTV are not very pliant.
Normal RTV does not bond well with rubber gaskets and causes slippage and bulging of the gasket. Used dry, rubber gaskets are only good where the oil pan bolts are very close together, it does not bridge wide (>2in) bolt holes
When replace a transmission gasket in my shop I almost always use a new cork gasket, super clean the mating surfaces with a rotary 3M tool, solvent clean the mating surfaces with Gum-cutter, & dry with a new kitchen-roll towel/dry oil-free cotton cloth.
If you look at a cork gasket there are usually a couple of bolt holes smaller than the other bolt-holes. put the gasket on the VERY CLEAN oilpan, push 2 bolts through to the smaller holes in the gasket. The smaller holes lock the bolts in place and locates the gasket on the pan This allows you to present the gasket and oilpan lined up correctly to the bottom of the transmission.
I fingertighten those 2 bolts, then add all the other bolts to finger tight ensuring the outer edge of the gasket is always in line with the pan.
Next I tighten all the bolts in a zig-zag pattern across the pan until they are all tight to 8lb/ft (torque wrench essential - you cannot guess this really) then tighten again in same pattern to 12lb/ft The bolts are really not that tight. Some pans have different torque settings but the torque setting is really a function of the gasket thickness and not the type of pan
I really have had no problems if you are clean, dont score any marks across the faces (Dont use heavy grit sandpaper) and have DRY mating surfaces. Draining the pan properly is a must as drips will spoil the gasket join.

Posted on Jan 07, 2009

Ad
  • 3679 Answers

SOURCE: Kubota rtv 900 transmission stuck in gear

follow this link to forum , this is very common and usually easy to fix
stuck in gear Archive Net Tractor Talk

Posted on Jun 15, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes a Kubota RTV 500 fuel pump to not operate in hot outside temperature?


Check the relay. If it's in not so good condition it'll over heat and stop power to the pump

Oct 22, 2016 | Cars & Trucks

1 Answer

Kubota troubleshooting


Check the cables going to the battery. Make sure you have a good ground and a good connection to the starter.

Jun 07, 2017 | Cars & Trucks

1 Answer

Kubota rtv 900 transmission stuck in gear


follow this link to forum , this is very common and usually easy to fix
stuck in gear Archive Net Tractor Talk

Jun 14, 2014 | Cars & Trucks

1 Answer

Kubota rtv 900


check your battery, if it is all right, you should check your ingiton and starter
_______________
tech2 scanner

Jan 22, 2013 | Cars & Trucks

1 Answer

HOW DO YOU CHANGE ATF OIL ?


You need to pull of the transmission pan to drain the fluid. Then you need to clean up the pan to transmission mating surfaces and install a new gasket or RTV silicone (most mitsubishi's use RTV). Next bolt the pan back to the tranny. If you use RTV make sure and let it setup(usually about 1 hour) before you put the new fliud in the transmission.

You may also want to replace the filter while the pan is off.

Jan 20, 2011 | Mitsubishi Montero Cars & Trucks

1 Answer

How to change transmission oil


You can have the fluid exchanged at a oil change store. That flush new fluid in transmission only. The proper way is to remove transmission pan to change the filter and to clean the magnet cake with metal shaving. (This can be a mess when you first release pan to drain the fluid) The next you need remove RTV from pan mating surface,then reseal it with RTV or a gasket. Then fill transmission with fluid

Apr 28, 2009 | 1997 Dodge Grand Caravan

2 Answers

Transmission gasket for 2007 HHR


Is the old gasket a resuable one meaning is it made of a hard plastic ? It should be and if it is there is no need for rtv on it it should not leak if it is make sure that everything is realy clean and make sure its the pan gasket if it is i would replace it. Most new cars are using reusable gaskets and for the most part i dont see any problems with them leaking.

Jan 07, 2009 | 1999 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...