Question about 2006 Jeep Liberty Limited

Open Question

How do I reset the factory alarm on my 2006jeep liberty

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: the alarm is not works for the jeep liberty 2002

This is common in all MOPAR vehicles. You will need to go to the dealer to correct this unless you are ASE certified in MOPAR electronics. It is a hard problem to diagnose as there are several causes.

Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconnect factory installed alarm


what does disconnect the larm mean.
hack it. (cut wires, etc)
make it dead for all eternity, including next owner
or just disable it for now, as the operators guide clearly states.

the alarms 1999 to now are highly integrated, and hacking dont work. (by design)

Apr 04, 2015 | 2004 Jeep Liberty

1 Answer

Jeep liberty clickers both will not work to lock and unlock doors and alarm


is it a factory alarm or after market . both have relays and fuse to them

Nov 05, 2012 | 2006 Jeep Liberty

1 Answer

How to determane if my jeep has a after market alarm or a factory?


The factory alarm is tied into your ignition switch. Most newer vehicles have an anti start system incorporated into this in case it is broken into. The alarm will shut the system down and will not allow the vehicle to start. Look under the dash under the driver side and see if you can locate a small box. Should have a serial number barcode on it. If so it has a factory alarm.

Mar 31, 2012 | 2007 Jeep Liberty

1 Answer

2006 jeep liberty. In the middle of the night the jeep would make a honking noise with short honks. We never had the alarm set. What would cause this and how would you turn the alarm system off.


the alarm automatically arms 30 seconds after you lock the doors
i looked around online and found info for you

The FACTORY ALARM DISARM WIRE IS
lt. green/orange '-'conn. 2, pin 9 @ the BCM.

The factory alarm disarm wire is
negative trigger thru a 473 ohm resistor.
MUST use relay. The BCM
(Body Control Module) is attached to
the left of the fusebox.
Connector 1 is a gray 26 pin plug,
and connector 2 is a gray 22 pin plug.

Once Located, splice into this wire with
a simular guage wire, add the specified resistor
and put it to a solid chassis ground.
This terminates the alarm functions entirely.

However, at this point, this car would be exceedingly
easy to steel, so I suggest you get an aftermarket
alarm system to protect it from here on in.

Take this info to your local
stereo/car alarm guy and have them
do this for you.

Sep 16, 2011 | 2006 Jeep Liberty

1 Answer

Engine won,t crank.I checked starter, and starter relay, good.There is an alarm system.....How do I reset factory alarm?


If the starter turns the engine when you jump from the hot lead to the trigger terminal/ then no further testing is required except that it is possible that the solenoid on the starter may be bad. Usually though they don't go bad all of a sudden and you would have a few weeks where you needed to turn the key a few times before it would engage. You need to check what I mentioned before.

Oct 14, 2010 | 2002 Jeep Liberty

1 Answer

The alarm is not works for the jeep liberty 2002


This is common in all MOPAR vehicles. You will need to go to the dealer to correct this unless you are ASE certified in MOPAR electronics. It is a hard problem to diagnose as there are several causes.

Mar 21, 2010 | 2002 Jeep Liberty

1 Answer

2002 Jeep Liberty - will not start after just turning it off.


the only other way around this is to have the factory installed alarm totally removed from the vehicle and that is pretty pricey

Sep 07, 2009 | 2003 Jeep Liberty

1 Answer

2002 Jeep Liberty Limited 3.7 V6 Auto with 4wd- Factory alarm system malfunction


all alarms have disable function usually located down underneath the driver side, look for a small toggle switch or momentary switch, turn the key to the on position , click the switch once or twice to the small red l.e.d light stays on constant.

Jul 18, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2006 Jeep Liberty Limited Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...