Question about Cars & Trucks

Open Question

2002 isuzu axiom the cruise control comes on by itself and the truck begins to pull back is there a cruise control fuse that I ca take out so it doesn't come on any more

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
sscullys
  • 984 Answers

SOURCE: 2002 Ford F150. Cruise control stopped working.

Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Posted on Feb 23, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Reset anti theft lock on Isuzu Axiom 2002


Wayne White wants more answers to this question
piggybacker....
post symptoms.
same car ?
what fails,
1: engine wont run immoblized
2: alarm dead.
3: alarm trips when all is good.
4: does car drive perfectly day and night.
5: do all other things work perfect. radio, lights?
6: do any cluster lamps fail, keyon, for example
the immobilizer lamp must go out, per operators guide.

we can not guess any of that.
it must be stated up front
why not start your own post.?
with all symptoms. good and bad.

Aug 21, 2013 | 2002 Isuzu Axiom

1 Answer

2002 isuzu axiom won't move when put in drive or reverse


ur linkage come un clipped from the rod that goes into the transmission or ur bands need adjusted if its a clutch bleed the clutch

Feb 27, 2013 | 2003 Isuzu Axiom

1 Answer

2002 isuzu axiom engine shuts off and will not start


I am also working on a 2002 isuzu axiom with the 3.5 engine that also starts for a few seconds then shuts off and will not start back up i did an engine over haul on it, and the engine ran before i removed the engine, did you find the problem?

Aug 07, 2012 | 2002 Isuzu Axiom

1 Answer

My key is stuck in the ingition switch of my 2003 isuzu axiom it will start the car and turn off to pass the acc point but won' t go to ock and come out


behind key switch youll find a cable just pull on it about 1/2 " it is connected to the button on the shifter easy to fix 1 screw must have fallen out

Oct 26, 2011 | 2002 Isuzu Axiom

1 Answer

2002 izuzu axiom w / 4L30-E transmission wont go into 4th gear downshifts to any gear at its own by itself


The place to start would be to pull diagnostic codes.If I was going to guess i would say a bad output speed sensor.Almost any trans code stored will inhibit fourth gear so guessing is tough.Good luck.

Mar 06, 2011 | 2002 Isuzu Axiom

2 Answers

I have a 2004 Isuzu Axiom, my check engine light came on as i was on the interstate with my cruise control on. The cruise control stop working exactly the same time the engine light came on. I took it to...


You may have actually had a faulty MAP that needed replace. Thing is that any time you get a "check engine", the cruise will be disabled. you must clear the code, by either a trouble code diagnostic tool, or disconnect the battery for about five minutes. Codes will clear, and cruise will start working again.

Nov 19, 2010 | 2004 Isuzu Axiom

1 Answer

2002 Isuzu axiom heater will not work. Gauge says it is working. We have checked the fuse.


you have to get air temp up to 90 before . it will get hot enough to kick on , mine does

Oct 29, 2010 | 2002 Isuzu Axiom

1 Answer

2002 Axiom drivers side windshield wiper doesn't work


the wiper arm mount is keyed(*tab to slot style) and it may have broken. Remove the wiper arm and look for the grooves.. no groves then it has been stripped and broken. Some also have a nut on top of the mounting point as a retainer. Just basically check where the wiper is attached to the control assembly.

Jul 11, 2009 | 2002 Isuzu Axiom

2 Answers

How to replace tail/stop light for a 2002 isuzu axiom


remove the hardware (2 bolts) then wiggle to loosen, now pull outwards (pull somewhat hard) towards the sides to clear some kind of guide. Then towards the rear<

Dec 16, 2008 | 2002 Isuzu Axiom

4 Answers

Leaking transmission fluid


How can I check transmission fluid on a 2002 Axiom - dipstick!

Jul 21, 2008 | 2002 Isuzu Axiom

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...