Question about Mazda Cars & Trucks

Open Question

1994 mazda mx 3 drivers side window is very difficult to roll down..how do I remove the door panel

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 124 Answers

SOURCE: remove driver's door panel

Start prying the door panel off with a flat head screw driver. It's held on by plastic clips, and a few screws. just pry it back and look in there with a flash light, you'll see. Just pry them out. If your lucky you'll only break a few. No real easy way to remove those.

Posted on Mar 23, 2009

Ad
  • 23 Answers

SOURCE: need to remove and replace the driver side door panel

Could be a bad switch, bad window motor, or clutch in window motor, ccould also be that the window itself jumped track.

Posted on Jun 16, 2009

emissionwiz
  • 76691 Answers

SOURCE: power window on driver side rolls down but will

REPLACE THE POWER WINDOW SWITCH

Posted on Jun 24, 2009

  • 4 Answers

SOURCE: Lincoln Town Car 1999 driver side window switch

I have the same problem in my 2001 towncar. I removed the switch control panel (without removing the door panel) by prying up from the front of the panel. There's a spring loaded plug under the mirror adjustment. Once you get that pulled up, the whole unit will lift out. Since there's a two year difference in the models - it MAY not work... however, you might not have to remove the whole door panel as you think.
In my case, the wiring was bad.

Posted on Sep 03, 2009

  • 1986 Answers

SOURCE: 2000 jaguar s-type driver window will not roll up

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to see the motor, regulator, guide rails

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my 2008 Mazda 3, the driver side window will roll down but not up. I replaced the window motor but that did no good. What do I need to do?


Check the rail for the window inside of the door. It sounds like something is funky with the guides. Sometimes a screw or rivet breaks and the up rail will not engage. You should take a picture of the way it looks when you remove the door panel, then have someone use the switch and watch as it goes down, and then have them go up, you should be able to see what mechanism isn't doing its job.

Jan 28, 2015 | Mazda Cars & Trucks

1 Answer

How do I fix the driver side window?


Keep slamming the door, you will
surely have more problems

Remove the door panel,see the problem & resolve it

I would guess you have a broken window regulator to replace

Dec 05, 2014 | 2006 Hyundai Santa Fe

1 Answer

Window won't rool up


If it is electric then you may have to replace the window motor, if it is a hand crank window then just take off the door panel and put the belt that goes from the crank to the chases of the window back on track, someone probably kept rolling it after it was already down

Feb 07, 2012 | 1992 Mazda MX-3

1 Answer

I have a Isuzu Rodea 2002. My driver side window wont roll up. Its a manual window. and when i start to roll it up it gets difficult half way up and acts like it might snap. but when i roll it down its...


sounds like it is off track, you will need to remove the door panel, screws in the arm rests, one on the crank or a snap ring, and possible one in the inner middle of the door panel, once all screws and crank are off/out the take a flat tip screw driver and work around the outer of the door panel as there are like 10 plastic clips on the inside of the panel, once panel is off inspect the regulator, this is attached to the window crank, make sure the cable is not frayed or broken if so then you will need a new regulator. Hope this helps Tim

May 09, 2011 | 2002 Isuzu Rodeo

1 Answer

On my 1994 dodge stealth, My passenger window rolled down, now it wont roll back up, how do i fix it? The driver side still works.


please disassemble the door trim remove the power window switch,remove the connector,get a multi tester to check the switch,move down the switch point to the terminal 1 and 2,3,4.if ok,move upward point to terminal 1 and 2,3,4, if no reading replace the power window switch

Mar 17, 2011 | 1994 Dodge Stealth

1 Answer

I have a 1996 Mazda Miata and the drivers side window crank will not turn any more. It has been sticking off and on for awhile and now it will not roll the window up at all. How do I get to it to fix it?...


remove the inner door cover, somtime's u need a spetial too to remove the handle befor this cane be doen, next check the track for ubsrutios and make shure the windon is stright in the track's

Jun 05, 2010 | 1996 Mazda MX-5 Miata

1 Answer

How do fix drver side rear sliding door window


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll see the innards of the door

Sep 21, 2009 | 2000 Mazda MPV

3 Answers

Power window on driver side door sticks


Yes the door's rubber window guide becomes dry and needs to be lubricated with a special silicone lubricant, go to Napa and ask for this silicone lube then apply it to the grooves located around the inner perimiter of the door window frame, sometimes it is neccessary to remove the door panel to access the lower window guides, if you remove the door panel becareful when removing clips along the lower part of panel you can damage the panel using a screw driver the sell a tool for this it looks like a screwdriver with a Y shape at the end. If this doesn't remidy the problem you more than likely have a worn out window motor that needs replacement.

Jul 02, 2009 | 1995 Volvo 850

2 Answers

My drivers side window will go down but not up


it is probably the motor in the window

May 14, 2009 | 1997 Honda Accord

2 Answers

1994 jeep grand cherokee power window problem


most of the time it is wires in the drivers door that break in the loom

Feb 20, 2009 | 1994 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...