Question about 2001 Kia Sportage

Open Question

Remove engine from kia sportage - 2001 Kia Sportage

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: How do you remove Audio-CD player from a 2002 Kia Sportage

after you remove all the screws from the dash you have to get down to a section by the pedals and remove something like the airbag to get at the last part of the dash apart. then you need to unplug the mirror and back wiper switches (opt i think). then you have access to your radio. These are all things i gathered from watching the guy at futureshop do, it was about $100 and now I don't have fm radio. but I am now going to try it on my own.

Posted on Oct 23, 2008

Molson02536
  • 3854 Answers

SOURCE: code for kia sportage tape and cd player

You can go to the dealer and have them help you get the code for the radio, if there going to charge you a crazy amount you can try www.radio-code.com. There cost is cheaper and can help you reprogram the code in your KIA. befor you go through all that, check for the code in the glove box, there might be a sticker in there or in your back pages to your manuel.
Good luck and hope this helps yougte your radio wokring again, keep me posted oh and try 0000 first. 

Posted on Jun 07, 2009

  • 14036 Answers

SOURCE: 2005 Kia Sportage serpentine belt

YOU NEED THE BELT TENSIONER TOOL ITS FITS IN THE SQUARE SLOTS IN THE TENSIONER.YOU ROTATE TENSIONER CLOCKWISE TO REMOVE BELT.

Posted on Aug 23, 2009

c17hydro
  • 2984 Answers

SOURCE: the easiest way to pull the heater core from a kia sportage-2000

There is no real easy way to do it....not like the older cars..

  1. Disconnect the negative battery cable.

    CAUTION After disconnecting the negative battery cable, wait for at least 10 minutes for the air bag module to deplete its stored energy.

    1. Remove the driver’s side air bag and steering wheel by performing the following procedure:
    2. Position the front wheels in the straight-ahead position.
  2. Remove the 4 steering wheel-to-air bag module bolts.
  3. Carefully, lift the air bag module and disconnect the electrical connector.

    CAUTION Place the air bag module in a safe location with the front facing upward.

  4. Remove the steering wheel-to-steering column nut.

    NOTE If may be necessary to mark the steering wheel to steering column alignment.

  5. Using a steering wheel puller, press the steering wheel from the steering column.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
    1. Remove the instrument panel by performing the following procedure:
    2. Remove both the rear and front consoles.
    3. Remove the knee bolster assembly.
    4. Remove the “T” bar section.
    5. Remove the relay bracket.
    6. Remove the turn signal assembly and the upper/lower steering column covers.
    7. Remove the hood release handle lockscrew, the hood release handle and the cable assembly nut.
    8. Remove the left side front pillar trim and the lower left side cover.
    9. Remove the 2 left side of the “T” bar-to-chassis bolts.
    10. At the left side of the instrument panel, remove the 3 instrument panel-to-chassis bolts.
    11. Remove the ashtray.
    12. Remove the center panel trim.
    13. Remove the ventilation control panel.
    14. At the center of the windshield next to the windshield, remove the cap and the mounting bolt.
    15. " Remove the right side front pillar trim and the lower right side cover.
    16. Remove the 2 right side of the “T” bar-to-chassis bolts.
    17. At the right side of the instrument panel, remove the 3 instrument panel-to-chassis bolts.
    18. Remove the steering column-to-instrument panel bolts and lower the steering column.
    19. Disconnect the instrument panel electrical connectors.
    20. Remove the instrument panel.
    1. Remove the blower/evaporator housing by performing the following procedure:
    2. Disconnect the air conditioning refrigerant lines from the evaporator core and discard the gaskets. Plug the openings to prevent contamination.
  8. Disconnect the fresh air control cable from the blower/evaporator housing inlet duct.
  9. Disconnect the 5 connectors from the bottom of the blower/evaporator housing.
  10. Move the carpeting from the bulkhead to gain access to the hole cover plate.
  11. Remove the 4 hole cover plate nuts and the plate.
  12. Remove the 2 upper blower/evaporator housing bolts.
  13. Remove the 2 lower blower/evaporator housing-to-bulkhead nuts.
  14. Remove the blower/evaporator housing.
  15. Disconnect the heater hoses from the heater core.
  16. Remove the temperature control cable from the heater housing.
  17. Remove the 2 lower heater housing nuts and the upper heater housing-to-bulkhead nut.
  18. Remove the heater housing.
    1. Disassemble the heater housing by performing the following procedure:
    2. Remove the seal from the heater core tube connections.
    • Remove the vent seal.
    • Remove the 2 wiring harness-to-heater servo screws.
    • Remove the 8 heater housing clips located on the servo side (left side).
    • Remove the left side of the heater housing.
    • Remove the 6 heater housing assembly clips.
    • Remove the 4 heater core tube mounting bracket screws and the bracket.
    • Remove the 8 remaining heater housing clips and disassemble the housings.
    • Remove the heater core from the housing.

  • f277857.gif
    Exploded view of the heater core and heater housing assembly—Kia Sportage


    THIS IS JUST TO REMOVE IT!

    Posted on Oct 18, 2009

    jturcotte
    • 8140 Answers

    SOURCE: 2002 KIA SPORTAGE. REPLACING FAN BELT NEED RO

    Hi, there are up to three belts if you have A/C. Each belt has a tensioning system. Diagrams and instructions from autozone.com are paste below. Please let me know if you have any questions, and thanks for using FixYa.

    A/C belt:
    jturcotte_1115.gif



    Alternator and fan belt:
    jturcotte_1116.gif
    top view of generator belt adjusting bolt C:
    jturcotte_1117.gif



    Power steering belt:
    jturcotte_1118.gif


    Removal & Installation

    A/C Compressor Belt

    1. Disconnect the negative battery cable.
    2. Loosen locknut (A).
    3. Remove the drive belt.

    To install:
    1. Properly route drive belt around the pulleys.
    2. Adjust bolt (B) until belt tension is 22 ft. lbs. (30 Nm)when measured at deflection point shown.
    3. Retighten locknut (A) to 24 ft. lbs. (32 Nm).
    4. Connect the negative battery cable.

    Alternator Belt
    1. Disconnect the negative battery cable.
    2. Remove the A/C belt.
    3. Loosen mounting bolts (A) and (B) from the back side of the alternator.
    4. Loosen adjustment bolt (C) and remove the drive belt.

    To install:
    1. Properly route drive belt around the pulleys.
    2. Adjust bolt (C) until belt tension is 22 ft. lbs. (30 Nm)when measured at deflection point shown.
    3. Retighten locknut (A) to 16 ft. lbs. (22 Nm)and locknut (B) to 32 ft. lbs. (43 Nm).
    4. Reinstall the A/C drive belt.
    5. Connect the negative battery cable.

    Power Steering Pump Belt
    1. Disconnect the negative battery cable.
    2. Remove the A/C and alternator drive belts for access.
    3. Loosen mounting lock bolt (A) and mounting bolt (B).
    4. With tension released removed the belt.

    To install:
    1. Properly route drive belt around the pulleys.
    2. Carefully pry on the power steering pump using a suitable lever. Adjust belt tension is 22 ft. lbs. (30 Nm) when measured at deflection point shown.
    3. Retighten bolts (A) and (B) to 31 ft. lbs. (42 Nm).
    4. Reinstall the A/C and alternator drive belts.
    5. Connect the negative battery cable.

    Posted on Feb 27, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How do I change the transmission seal on a 2002 kia sportage?


    remove the drive shaft place a jack under the transmission and remove the trany mounts and bellhousing bolt any lines and linkage attached to the transmission separate tranny from engine

    May 16, 2014 | 2002 Kia Sportage

    1 Answer

    How to change plugs on 02 kia sportage


  • 1

    Keep a regular schedule for inspecting the spark plugs on your 2002 Kia Sportage. According to the official 2002 Kia Sportage owner's manual, spark plugs and ignition wires should be inspected every two years or 48,000 miles, whichever comes first.

  • 2

    Let your 2002 Kia Sportage sit for a few hours before opening the engine compartment. You want to make sure that the engine is cool before you begin working on it.

  • 3

    Pop open the hood of your Sportage and locate the ignition wires, which will be attached to the top of your engine. The 2002 Kia Sportage has a four-cylinder engine, meaning there are four spark plugs each attached to an ignition wire. The ignition wires run from the engine to the fuse box, which is located in the left side of the engine compartment.

  • 4

    Inspect the ignition wires of your 2002 Kia Sportage. These wires will need to be replaced if they appear worn.

  • 5

    Disconnect the ignition wire to your spark plugs. Grab the rubber boot located near the base of the wire and pull upward instead of yanking on the wire. Remove only one wire at a time, or mark the wires with a colored Sharpie marker before disconnecting all of them. Improperly reconnecting the ignition wires can seriously affect the performance of your Kia Sportage.

  • 6

    Attach the spark plug socket to your socket wrench. Use the socket wrench to remove the spark plug from the top of the engine's cylinder.

  • 7

    Inspect the spark plug. There will be some soot, but if the spark plug is completely covered in soot, it needs to be replaced.

  • 8

    Position your replacement spark plug in place and secure it with the spark plug socket on your socket wrench. Be careful not to overtighten the spark plug after it has been snuggly fitted.

  • 9

    Position the rubber boot of the proper ignition wire in place above the spark plug and insert it with your hands. Close the hood of your 2002 Kia Sportage

  • Mar 16, 2011 | 2002 Kia Sportage

    1 Answer

    Location of engine number on kia sportage 2005 model(R2)


    you'd have to remove the engine its on the back. $5 pls. thanks. ;)

    Jan 15, 2011 | 2005 Kia Sportage

    1 Answer

    How do I remove the starter on a 2000 Kia Sportage with 4WD?


    It has three bolts that need to be removed. There is a support bar attached to the engine block and bottom of intake manifold. Remove this and the starter will drop down.

    Nov 21, 2010 | 2000 Kia Sportage

    1 Answer

    Does the 2002 Kia Sportage have an noninterference engine or does it have an interference engine?


    2002 Kia Sportage 2.0L dohc, is an interference engine, will cause piston to valve damage, Kia recommends timing belt replacement in California every 90,000 miles, except California every 60,000 miles, hope this was very helpful.

    Sep 03, 2010 | 2002 Kia Sportage

    1 Answer

    Kia spotage


    no remove the head then remove the camshaft ,turn the head upside down and fill the combustion chambers with oil and make sure the valves are sealing ,i do fell you only have bent valves

    Dec 14, 2009 | 1995 Kia Sportage

    2 Answers

    How to remove the headlights on a 2001 Kia sportage


    remove the indicator lens by pulling on the spring/bracket inside the engine bay and you should find another bolt

    Feb 11, 2009 | 2001 Kia Sportage

    2 Answers

    Need wiring diagram for 2001 kia sportage , need it for fuel pump


    2002 kia optima has no fire to the spark plugs
    or spark plug connector

    Jan 20, 2009 | Kia Sportage LX Cars & Trucks

    1 Answer

    97 KIA SPORTAGE ENGINE NUMBER LOCATION


    you'd have to remove the engine its on the back.

    Aug 20, 2008 | 1999 Kia Sportage

    Not finding what you are looking for?

    Open Questions:

    See all 2001 Kia Sportage Questions

    2001 Kia Sportage Logo

    Related Topics:

    33 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8140 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...