Question about 2011 Citroen C-Crosser HDi

Open Question

Reset key fob ccrosser ignition - 2011 Citroen C-Crosser HDi

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CL220, fob wont open doors I can't get in the car, does this mean the battery is flat?


battery may be flat in the fob or the vehicle has forgotten the code for the fob. and will need resetting. change the battery use the key to open the door put key in the ignition. ( fob Ir old type leave fob off the key) turn to number 2 and press fob till doors lock and unlock. then its reset. dont be worried if the alarm goes off while doing this it will go off when the code is restored. if you have 2 fobs you will need to rest that one to.

Mar 17, 2014 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

W202 ignition key wont turn past1


  • Reset your Mercedes-Benz key by placing the key in the ignition of your vehicle while the vehicle is turned off. Do not turn on the vehicle. Press a finger on the "lock" button of your key fob while the key is in the Mercedes' ignition.

  • Pull the key out of the ignition while continuing to hold the "lock" button down. Continue to hold the "lock" button for the duration of the key resetting process

  • Use another finger to push down on the "unlock" button five consecutive times. Keep holding down the "lock" button.

  • Release the "lock" button. This is the end of the resetting process for your Mercedes-Benz. Use your key fob to ensure it is properly working



  • Read more: How to Reset a Mercedes Key ' eHow.com http://www.ehow.com/how_7492936_reset-mercedes-key.html#ixzz2DPwSK6xa


  • Read more: How to Reset a Mercedes Key ' eHow.com http://www.ehow.com/how_7492936_reset-mercedes-key.html#ixzz2DPwCappG

    Nov 23, 2012 | 2008 Mercedes-Benz Mercedes Benz C Class

    1 Answer

    How do i reset my alarm on my bmw 3 series without fob


    engine management should read the transponder chip in your key and deactivate the alarm the battery in the key is charged while key is in ignition if the key hasn't been used for a while maybe its flat

    Jan 14, 2012 | BMW 3 Series Cars & Trucks

    1 Answer

    Doors do not centrally lock with fob or key (they close but open straight away). Onlu option is lock drivers side with key and then lock the other 3 doors manuually. Ford Fiesta Mark 6 in the UK


    hi
    you need to try a couple of diffrent things with this problem


    1- get in drivers seat close doors and lock by hand
    ,
    2- then put key in ignition and turn key till dash lights come on (do not start)

    3- while key in ignition unlock doors with fob ,

    4 - then lock again with fob while key in ignition.

    5- then remove key exit car try locking doors from out side this should reset all your door locks

    Oct 25, 2010 | Ford Fiesta Cars & Trucks

    1 Answer

    Battery in key fob went dead need to reset keyfob audi tt 2000


    hi you can do this but you will have to have a key that does not have a remote/fob on it ( basically just go get one cut cheaply ) then to reprogram keys/key fob's first using the key without fob, turn ignition on ( do not turn over, just to position 2) then lock drivers door with other key ( do not use fob, just the key itself with fob now complete the following within 30 seconds within 5 seconds( of locking the car) press the unlock button on the first key once ( this programs that key as key memory1) the indicators should flash once to indicate signal received wait 5 seconds then press unlock on key fob vehicle should then unlock meaning key fob has been programmed and programming ended open door turn ignition off , and that's it, it should work if you have more than 1 key with fob, do the same as above but instead of pressing unlock once, you do it twice, if third key 3 x if fourth key 4 x etc etc,

    Sep 20, 2010 | Audi TT Cars & Trucks

    1 Answer

    Replaced starter on '99 Yukon. When reconnected


    I can't say for sure but it sound like you either trigger the "Panic" button or alarm system if equiped. Hook the battery up (negative last) and push the "Panic" button on the key FOB.
    If you don't have the FOB you may be able to reset but disconnecting the negative cable only.
    If it's an alarm system, locking and then unlocking with the FOB should reset it, also using the key to turn on the ignition is supposed to reset it.

    Jun 06, 2010 | 1999 GMC Yukon

    1 Answer

    Remote control receiver unit were is it , and a pic of it to reset key fob on a hyundai coupe se 2000cc year 2002


    This reset for key fob Hyundai coupe year 02 to 04
    Turn ignition to position two
    Press lock or unlock once
    Ensure indicators flash once to confirm reset
    This will enable fob providing you have no other faults
    Good luck barry

    May 12, 2010 | 2003 Hyundai Tiburon

    1 Answer

    Resetting a Key fob on 2007 Honda Pilot


    to program a key fob- get in vehicle and close all doors. insert key into ignition, have all the key fobs you want to program for this vehicle in hand, programing erases all old fobs. turn the ignition switch to on(all dash lights light up, on click before starting the car). then hit the lock button on one of the fobs. turn the ignition to lock. turn the ignition back to run and press the lock button again from the same remote. repeat untill all the locks cycle. ones the locks cycle keep the ignition in run and press the lock button on each key fob(the ocks will cycle each time a button is pressed). then turn the ignition to lock after all fobs have been programed

    Dec 31, 2009 | 2009 Honda Pilot

    1 Answer

    Need to reset the key fob after replacing the battery


    You should not have to reset the key fob after a battery replacement. The signal from the key fob stays the same and is programed to the reciever.
    If the key fob needs to be reprogrammed then follow these steps.
    1. Have all key fobs with you during programming.
    2. Sit in the vehicle with all doors closed.
    3. Lock all doors using the Lock/Unlock switch on the door.
    4. Insert and withdraw the ignition key 7 to 9 times within 10 seconds (do not turn the key, just insert and withdraw).
    5. The 4 way flasher indicator on the dash should flash once or twice.
    6. Insert the ignition key and turn it on (key on, engine off).
    7. Press any button on one remote and the 4 way flasher indicator on the dash should flash once.
    8. If you have more key fobs to program use the Lock/Unlock button on the door to unlock the doors and then lock the doors.
    9. Press any button on the next key fob and the 4 way flasher indicator on the dash should flash once.
    10. Repeat if you have more key fobs. Only 5 can be programmed.
    11. To exit, simply turn of the igniton and remove the ignition key.
    12. Unlock the doors using the Lock/Unlock switch on the door and exit the vehicle.
    13. Make sure the window is down when testing remotes in case you leave the keys inside.
    14. Close all doors and test all remotes that were programmed.

    Do not skip any steps or the process will not work.

    If the 4 way flasher indicator does not work when inserting the key, you will need to start the process from the begining. If it still does not work the receiver may be your problem.

    If the 4 way flasher indicator does not flash when pressing any button on the key fob then the key fob is the problem (dead battery or defective remote)

    Dec 18, 2009 | 2002 Nissan Xterra

    3 Answers

    I need to reset my peugeot 406 key fob


    Had same trouble with my 406, fixing no problem, with new battery in fob, insert into ignition, turn key, BUT DO NOT START ENGINE, hold button for about 10 seconds release button and remove key from ignition, then try and see if doors lock on remote, if not try again, had to do this a couple of times, and it worked, sorry to say that now my key fob button has completely fell apart, through ware and tare

    May 19, 2009 | 2005 Peugeot 405

    Not finding what you are looking for?
    2011 Citroen C-Crosser HDi Logo

    Related Topics:

    99 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Citroen Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14338 Answers

    Are you a Citroen Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...