Question about Dodge D150

Open Question

How to replace ignition lock cylinder 1990 d150

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

Ad

SOURCE: need to replace 280zx ignition lock cylinder

we have a 71-681. we don't have a key.

Posted on Apr 17, 2009

  • 3 Answers

SOURCE: how do i replace ignition cylinder in volvo 2002

The link below is not for your exact model, but may be of help:
http://volvospeed.com/Repair/ignition_S80.html

Posted on Jan 13, 2010

  • 880 Answers

SOURCE: I have a 1990 cadillac deville, it was running

If you're saying it turnes over but doesn't start I think of two things. If it is not getting power to the spark plugs I think it is the ignition module inside the distributor(small black box on bottom inside). If it is getting power to the spark plugs I would check the fuel pressure. If no or little fuel then fuel filter and or the fuel pump.

Posted on Jan 20, 2010

  • 40 Answers

SOURCE: replacing a ignition key cylinder lock housing

the thing is that you can replace it, but the still will not run, the transponder and key have to be reprogrammed at the dealer only

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

To JTurcotte - Your discussion and directions on how to repair the 1990 Jeep Cherokee srteering column were very good. I have a similar but not exact problem. The key would not come out of the...


WHEN YOU INSTALL NEW LOCK CYLINDER, TURN THE KEY TO THE LOCK POSITION. INSERT THE LOCK CYLINDER INTO THE HOUSING FAR ENOUGH TO CONTACT THE DRIVE SHAFT FORCE IT INWARD AND MOVE THE IGNITION SWITCH ACTUATOR ROD UP AND DOWN TO ALIGN THE COMPONENTS. WHEN THE COMPONENTS ALIGN, THE CYLINDER WILL MOVE INWARD AND THE SPRING LOADED RETAINER WILL SNAP INTO PLACE LOCKING THE LOCK CYLINDER IN THE HOUSING.

Sep 11, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

How to replace column ignition key switch on 1990 gmc safari


THIS REQUIRES A FEW SPECIAL TOOLS YOU WILL HAVE TO PULL THE STEERING WHEEL, & THE LOCK PLATE, THAT LOCKS THE STEERING WHEEL & THE TURN SIGNAL SWITCH. THERE IS A SCREW UNDER THE TURN SIGNAL SWITCH THAT HOLDS THE IGNITION LOCK CYLINDER IN PLACE. YOU MAY HAVE TO TAKE IT TO A SHOP. TOOLS ARE STEERING WHEEL PULLER & A LOCK PLATE SPRING DEPRESSOR, & PHILLIP SCREWDRIVER & A TORX SCREWDRIVER.

Jan 17, 2011 | 1990 GMC Safari

1 Answer

How do you change the ignition lock cylinder on a 1990 dodge dakota?


I just recently had to replace the ignition lock cylinder on a 1990 Dodge Dakota. If yours is anything like mine the ignition lock cylinder you need is for a 1989 Dodge Dakota. All you have to do to replace it is remove the center of the steering wheel and the steering wheel. Next you will have to remove the lock plate. After you do that you should be able to pull everything else out of the way. Then all you have to do is take a flathead screw driver and pop the old ignition out. You will need a steering wheel puller and a steering wheel lock plate remover. The best thing to do with the lock cylinder is to go to autozone or whatever store you use and match it up. Good luck

Nov 28, 2010 | 1990 Dodge Dakota

1 Answer

How to change 1999 VW cabrio ignition lock cylinder. How do I get the cylinder out of the aluminum housing?


autozone.com has a free repair guide, see below

printpage_icon.gif


REMOVAL & INSTALLATION

1990-94 Cabriolet,1990-93 Fox, 1990-92 Golf and Jetta


0900c15280267f2b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Lock cylinder drill point.

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel, then remove the steering column covers.
  3. Remove the turn signal and wiper switches.
  4. Disconnect the ignition switch wiring.
  5. On some models, the hole in the lock body for removing the ignition lock cylinder was not drilled by Volkswagen. To make the hole, use the following measurements in conjunction with the illustrations. Drill the hole where "a" and "b" intersect on the lock body. The hole should be drilled 0.19 inch (3mm) deep
  6. Remove the lock cylinder by pushing a small drill bit or piece of wire into the hole and pulling the cylinder out. It might be easier to insert the ignition key, turn it to the right a little and pull on it.

To install:
  1. Insert the lock cylinder into the housing with the key in the cylinder.
  2. While gently turning the key side-to-side, press the cylinder in to the stop. It should click into place.
  3. Temporarily fit the steering wheel onto the splines, then make sure the column locks and unlocks smoothly.
  4. Install the switches, column covers, wiring and the steering wheel.
  5. Connect the battery cable.

1995-99 Cabrio, 1993-99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal.


NOTE Always use a new shear pin when installing the lock cylinder.

Oct 08, 2010 | 1999 Volkswagen Cabrio

1 Answer

Remove security off a 1990 camaro because changed the ignition


One way is to change out the chip from the cars computer. Another way is use a General Motors GM VATS Override Bypass Kit, I'v learned that there is a pre-packaged set of resistors for the 15 GM resistor values I found a place called Sonic Electronix. Sonic here it is: http://www.sonicelectronix.com/item_...+DEI+652T.html
There is also a bit of misinformation on the internet Some tips I've learned when searching out this.
Example: Myth: The standard ignition cylinder lock will not fit or work in place of the vats ignition cylinder lock. Wrong! The standard 1990 camaro cylinder lock fits slightly deeper inside the column, so this takes away your ability to push in the key and turn it backwards for the accessory position. Other than that, it works fine for turning on the ignition.
I hope this helps some.

May 13, 2010 | 1990 Chevrolet Camaro

1 Answer

How do we replace the ignition lock on a 1990 ciera when the tumblers are damaged? can't turn it to remove normally?


Make sure the key itself is not worn.If it is good then you need a steering wheel puller to remove the steering wheel and to get to the ignition cylinder.You also need a lock plate compressor tool to remove the lock ring on the lock plate.The turn signal switch has to be pulled out of the way to get to the bolt that holds the cylinder in the column.Once the cylinder is out you can have it repaired at a dealership.They have the tools for repairing ignition cylinders and you don`t have to get new keys.As long as it is not to worn out.Hope this helps.Good luck.

Apr 05, 2010 | 1990 Oldsmobile Cutlass Ciera

1 Answer

How do I change the ignition switch in my 1990


  1. Disconnect battery ground cable.
  2. Place lock cylinder in the Run position.
  3. Remove steering wheel.
  4. Remove turn signal switch. It is not necessary to completely remove the turn signal switch from the column. Pull switch rearward enough to slip it over the end of the shaft. Do not pull the harness out of the column.
  5. Remove attaching screw and lock cylinder set. Do not drop the screw into the column.
  6. To install, align cylinder key with keyway in housing, as shown in Fig. 1. Push the lock completely inward, install attaching screw and torque to 40 inch lbs., on standard columns, or 22 inch lbs., on tilt columns.

Dec 04, 2009 | 1990 Chevrolet K1500

1 Answer

1990 Jeep Cherokee Ignition key replacement


Removal & Installation
Without Air Bag
See Figures 1, 2, 3 and 4
  1. Remove the turn signal switch.
  2. Insert the key in the lock cylinder and turn it to the ON position.
0900c152800a9f7f.jpgFig. 1: Using a pair of needle nose pliers, remove the key warning buzzer switch and contacts from the steering column
  1. Remove the key warning buzzer switch and contacts AS AN ASSEMBLY using needle-nosed pliers, or a paper clip with a 90° bend.
0900c152800a9f80.jpgFig. 2: Lock cylinder retaining screwSome steering columns may have a retaining screw holding the lock cylinder in the column. When servicing this type, simply remove the retaining screw and remove the lock cylinder.
0900c152800a9f81.jpgFig. 3: Using a small thin bladed tool, press in the ignition lock clinder retaining tab ... 0900c152800a9f82.jpgFig. 4: ... then pull out the lock cylinder from the steering column
  1. With the ignition switch still in the ON position, insert a thin screwdriver into the slot adjacent to the switch attaching screw boss (right-hand slot). Depress the spring latch located at the bottom of the slot to release the lock cylinder.
  2. Remove the lock cylinder.
To install:
  1. To install the lock cylinder, turn the key to the LOCK position. Insert the lock cylinder in to the housing far enough to contact the drive tang. Force it inward and move the ignition switch actuator rod up and down to align the components. When the components align, the cylinder will move inward and the spring-loaded retainer will snap into place locking the lock cylinder in the housing.
If the lock cylinder is retained by a screw, tighten the screw to 40 inch lbs. (5 Nm).
  1. Install the key warning buzzer switch.
  2. Follow the ignition switch installation procedures to adjust the ignition switch.
  3. Install the turn signal switch.
With Air Bag
Please refer to the ignition switch removal and installation procedure.50c573d.jpg73cc55f.jpgb9448d0.jpg278f367.jpg

Oct 22, 2008 | 1990 Jeep Cherokee Limited

1 Answer

Replace ignition tumbler


STEP BY STEP Please Remember to Rate Me Thank You RejakWilson




WARNING: On vehicles equipped with Airbags, disable airbag system prior to performing service procedures.



  1. Disconnect battery ground cable.
  2. Remove steering wheel as outlined under STEERING WHEEL procedure.
  3. Using a screwdriver, pry cover from housing.
  4. Using lock plate compressing No. J-23653 or equivalent, compress lock plate, and pry snap ring from groove on shaft, Fig. 5. Slowly release lock plate compressing tool, then remove tool and lock plate from shaft end.
  5. Slide canceling cam and upper bearing preload spring from end of shaft.
  6. Remove turn signal (multi-function) lever.
  7. Remove hazard warning knob retaining screw, button, spring and knob.
  8. Remove pivot arm.
  9. Wrap upper part of electrical connector with tape to prevent snagging of wires during switch removal.
  10. Remove switch retaining screws and pull switch up from column, guiding wire harness through column.
  11. Reverse procedure to install.



  1. Remove turn signal switch as outlined under TURN SIGNAL SWITCH.
  2. Remove buzzer switch and spring clip. On 1990-92 models, ignition key must be removed from lock to remove buzzer switch. On 1991-92 models, switch and spring clip are one assembly.
  3. Turn lock cylinder to Run position on 1989 models or Lock position on 1990-92 models, then remove lock cylinder retaining screw and the lock cylinder.
  4. To install, rotate lock cylinder to the stop while holding housing. Align cylinder key with keyway in housing, then push lock cylinder into housing until fully seated. Lock cylinder must be in Run position to install buzzer switch.
  5. Install lock cylinder retaining screw, then the buzzer switch, turn signal switch and steering wheel.

Aug 30, 2008 | 1989 Chevrolet Celebrity

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...