Question about Cars & Trucks

Open Question

Head bolt torque for 1997 honda valkyrie - Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

GMJunkie
  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 honda odyssey 3.5 head bolt torque spec


Apply new engine oil to the threads and flanges of the cylinder head bolts.

Tighten the cylinder head bolts sequentially in three steps.

NOTE: Perform each step twice.

1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.)
2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.)
3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.)

Feb 28, 2014 | 2000 Honda Odyssey

1 Answer

HEAD TORQUE AND SPECS FOR A 2001 HONDA ACCORD 2.3L


Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

10_29_2012_10_15_36_pm.gif

Oct 29, 2012 | 2001 Honda Accord

1 Answer

Need torque specs for bolts on head of my 2002 honda civic ex v-tech 1.7 engine. just fixed them about a week ago and have to fix them again


Hello claudian1535,

Below is an image showing the torque sequence. The torque procedure is a three step process:

Step one torque all head bolts to 14 ft.lbs.
Step two torque all head bolt to 36 ft.lbs.
Step three torque all head bolts 49 ft.lbs.


netvan_116.png

I hope this helps.

Regards,

netvan

Jul 21, 2011 | Honda Civic Cars & Trucks

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

Torque para cabeza honda civic motor 1.6


1996-97 Civic and Civic del Sol
1.6L (D16Y5, D16Y7 and D16Y8) ENGINES

Tighten the cylinder head bolts to their final torque specification in four steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows:
  1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
  2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
  3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
  4. Step 4: Retighten only the two center bolts to 49 ft. lbs. (67 Nm).

Hope helps (remember to rate and comment this).

Sep 23, 2010 | 1997 Honda Civic

1 Answer

2000 honda civic sir 1.6 dual cam vtec head torque and head bolt location


The Head bolts are located below the cams, so you have to take the cams out to get to the bolts.
The torque specs for the head bolts in sequence is 20, 40, then end at 63ft lbs. Be sure to apply anti sieze or dip the head bolts in oil, before you torque them down or you might pull out the threads. (Not a good thing TRUST ME!)
Hope this helps.

Aug 10, 2010 | 2000 Honda Civic

2 Answers

Had the timing belt break on my 1997 Honda accord change the belt and water pump did compression test cause motor was shaking even do the timing was set right so had mechanic look at it and said it bent a...


yes a bent valve is a very hard task, you must of couse pull the engine cylinder head off and then replace the valve, this takes special tools.

May 19, 2010 | 1997 Honda Accord

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Hi what is the head torque on a 2002 honda civic


Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Mar 25, 2010 | 2002 Honda Civic

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    35 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...