Question about 2004 Lincoln Town Car

1 Answer

Door module Is the door module and anti lock module the same thing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 4,369 Answers

No, different.

Principles of Operation
Note: Upon installation of a new driver door module (DDM), the module must be reconfigured. Refer to Section 418-01 . The DDM is connected on the standard corporate protocol (SCP) communication network. The DDM controls many functions including power windows, power door locks and remote keyless entry. The DDM also communicates with the driver seat module (DSM) to control the power mirror and seat memory functions.
--------------------------------------------------
Principles of Operation
The driver seat module (DSM) is connected on the standard corporate protocol (SCP) communication network. The DSM controls the driver power seat and communicates with the driver door module (DDM) to control the driver seat memory and both outside memory mirror functions.
---------------------------------------------------
Principles of Operation
The lighting control module (LCM) is a microprocessor based module that controls several vehicle subsystems. The LCM responds to electrical input signals from various switches, sensors, and external modules. The LCM is located under the LH side of the instrument panel. Subsystem functions of the LCM include headlamps with autolamps, turn signal lamps/hazard flasher lamps, cornering lamps, parking lamps, daytime running lamps (DRL), courtesy lamps, demand lamps, battery saver and control backlighting. The LCM interfaces with the driver door module (DDM) through the standard corporate protocol (SCP) communication network for the illuminated entry feature.
----------------------------------------------------
Principles of Operation
The air suspension module is linked to its own data link connector (DLC). The air suspension module controls the air suspension and the variable assist power steering VAPS. For additional air suspension system information, refer to Section 204-05 .
The air suspension module is used to monitor and control the VAPS system. The VAPS system controls the level of power assistance available to the driver based on vehicle speed and rate of change in steering position. For additional VAPS system information, refer to Section 211-00 .
-------------------------------------------
DESCRIPTION AND OPERATION Module Controlled Functions
DIAGNOSIS AND TESTING Diagnostic Trouble Code Chart Air Suspension Module Principles of Operation
Inspection and Verification
Symptom Chart
Pinpoint Tests
Driver Door Module (DDM) Principles of Operation
Inspection and Verification
Symptom Chart
Pinpoint Tests
Driver Seat Module (DSM) Principles of Operation
Inspection and Verification
Symptom Chart
Pinpoint Tests
Lighting Control Module (LCM) Principles of Operation
Inspection and Verification
Symptom Chart
Pinpoint Tests
REMOVAL AND INSTALLATION

Posted on Apr 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

OK the driver door puddle light, code access buttons, and power door lock button do not work while engine is off. BUT... the door lock button works when engine is running. Also, It seems as if the car...


It's hard to check the relay's for the door locks if you don't know where they are . They are not silver can type , they are one inch square ! They are located behine driver side rear quarter panel .
NOTE: The door ajar state will be monitored continuously for 500 ms after locking has occurred. If a door is opened again within 500 ms, the driver door will unlock
The electronic door lock system has three main components: the remote anti-theft personality (RAP) module, attached to the rear left hand quarter panel, the three-button (hand held) keyless entry remote transmitter (15K601), and the keyless entry keypad (14A626) on the driver side door.
The door locks are controlled by the RAP module through three external relays: the driver unlock relay (if equipped with two step unlocking), the all unlock relay, and the all lock relay. These relays are located in the relay box on the LH rear quarter panel.
The keyless entry remote transmitter initiates the following electronic door lock system functions:
Do you know what DTC'S - diagnostic trouble codes are ?
RAP Module Diagnostic Trouble Code (DTC) Index
RAP Module Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By Action B1309 Power Door Lock Circuit Short to Ground RAP GO to Pinpoint Test C . B1341 Power Door Unlock Circuit Short to Ground RAP GO to Pinpoint Test C . B1485 Brake Pedal Input Circuit Short to Battery RAP GO to Pinpoint Test D . B1526 Keyless Entry Keypad Switch Circuit Short to Ground RAP GO to Pinpoint Test B . B1629 PRNDL Reverse Input Short to Battery RAP GO to Pinpoint Test E . B1845 Ignition Tamper Circuit Failure RAP Invalid DTC. Ignore this DTC. B2425 Keyless Entry Out of Synchronization RAP GO to Pinpoint Test C . B1334 Decklid Ajar Rear Door Circuit Short to Ground RAP REFER to Section 417-02 . .Without seeing if any codes are stored could go in a wrong diagnostic direction . You don't want to change parts that are not needed .
  1. Remove the LH rear quarter trim panel; refer to Section 501-05 .
  1. Disconnect the two remote anti-theft personality (RAP) module electrical connectors.
Generic Electronic Module (GEM)/Central Timer Module (CTM) Controlled Functions
The generic electronic module (GEM) is equipped on four-wheel drive vehicles with power windows. The central timer module (CTM) is equipped only on two-wheel drive vehicles without power windows.
NOTE: GEM/CTM diagnostics are compatible with the scan tool.
The GEM/CTM incorporates the functions of several different modules into one, and offers diagnostics to easily locate and repair concerns affecting the subsystems that it controls.
The GEM/CTM constantly monitors the systems it controls and reports a concern in the form of a diagnostic trouble code (DTC). A DTC can be retrieved with the scan tool through the communication link.
The scan tool is a menu-driven tester that allows the user to run specific tests. The scan tool can isolate faults in the GEM/CTM subsystems through a symptom-driven diagnostic procedure. Connecting the scan tool to the GEM/CTM communication link will not alert the GEM/CTM. If the GEM/CTM is "asleep" when the diagnostic connector is plugged in, the GEM/CTM must be "awakened". If the communication link cannot be established, turn the ignition to RUN.
NOTE: The GEM/CTM has a sleep function to minimize battery consumption. During the sleep mode, the GEM/CTM turns off all outputs and monitors only the following:
  • door ajar (driver door, passenger door, liftgate, LH rear and RH rear doors).
  • key-in-ignition.
  • key in RUN or ACC.
  • two-step unlock switch (unarm switch).
  • digital TR sensor.
  • illuminated entry request (remote anti-theft personality [RAP] module).
  • . There are more DTC'S for the GEM ,too many too post here . There is also a relay module behind the dash , looks like behind the radio , heater / A/C panel .
Do you know how to do automotive electrical testing using a wiring diagram an a DVOM - digital volt ohm meter ? How to test power an grounds ?

Electric Testing Techniques You Need to Know
You can view wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model an engine size . Under system click body & accessories , sub system click power locks .Then click search , then click on the links one at a time . Watch this video ,

Door Locks Go Crazy 1 watch all three . This a dodge , doesn't matter , just want to show how to test .

Apr 22, 2017 | 2002 Ford Explorer

1 Answer

I need a radio wiring digram color code for 2009 chevy silverado


2009 CHEVROLET SILVERADO C1500 4DR TRUCK WITH 4.3L ENGINE AND STANDARD AUDIO SYSTEM

Remote Start
WIRE COLOR POLARITY LOCATION
Battery RED/WHITE (+) IGNITION SWITCH HARNESS
LOW CURRENT, FOR HIGH CURRENT USE RED/BLACK AT VEHICLE FUSE BOX
Ignition 1 PINK (+) IGNITION SWITCH HARNESS
Accessory 1 BROWN (+) IGNITION SWITCH HARNESS
MAY BE YELLOW ON SOME MODELS
Accessory 2 PINK/BLACK (+) IGNTION SWITCH HARNESS
FOR REMOTE START INTEGRATION
Starter 1 YELLOW/BLACK (+) AT MODULE UNDER HOOD BEHIND DRIVER HEADLIGHT
NOT FOR REMOTE START, FOR REMOTE START INFORMATION
Starter 2 PINK/BLACK (+) IGNITION SWITCH HARNESS
FOR REMOTE START INTEGRATION
Anti-Theft Type GM PASSKEY III® ANTI-THEFT SYSTEM
Anti-Theft Descript THE KEY SENDS AN RF SIGNAL TO THE BCM MODULE THROUGH AN ANTENNA LOCATED AROUND THE IGNITION CYLINDER
Key Sense PINK (+) IGNITION SWITCH HARNESS
Tachometer WHITE (-) AT IGNITION COIL
Speed Sense YELLOW/BLACK (AC) AT ECM MODULE UNDER HOOD ON DRIVER FENDER
BLACK PLUG PIN #57
Parking Lights LIGHT BLUE (-) AT VEHICLE LIGHT SWITCH
Brake Lights LIGHT BLUE/WHITE (+) AT SWITCH ABOVE BRAKE PEDAL
IGNITION MUST BE ON FOR THIS WIRE TO TEST
Reverse Lights DARK BLUE (+) AT BCM MODULE UNDER DRIVER DASH
Horn TAN (-) IN HARNESS AT STEERING COLUMN
ALSO AT BCM MODULE UNDER DRIVER DASH
Modules
WIRE LOCATION
Please select another category
Doorlocks/Windows
WIRE COLOR POLARITY LOCATION
Power Unlock WHITE (-) AT BCM MODULE UNDER DRIVERS SIDE OF DASH
THIS WIRE UNLOCKS THE REAR DOORS ONLY, WILL REQUIRE A 5-WIRE SET-UP IN EACH FRONT DOOR TO INTEGRATE OR A SERIAL DATA MODULE FROM AN ALARM MANUFACTURER
PowerLock LIGHT BLUE (+) AT BCM MODULE UNDER DRIVERS SIDE OF DASH
THIS WIRE LOCKS THE REAR DOORS ONLY, WILL REQUIRE A 5-WIRE SET-UP IN EACH FRONT DOOR TO INTEGRATE OR A SERIAL DATA MODULE FROM AN ALARM MANUFACTURER

i would use a DLPK module

DLPK (2009 Chevrolet Silverado)
W2W
CC-Heated Seats Activation
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
PK-Immobilizer Bypass-Data No Key Req'd
RS-RAP Shut Down (Remote ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Front Door Pins
SS-Entry Monitoring Hood Pin
D2D
CC-Heated Seats
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
PK-Immobilizer Bypass-Data No Key Req'd
RS-RAP Shut Down (Remote ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Front Door Pins
SS-Entry Monitoring Hood Pin


Hope helps.

Mar 31, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

The panic alarm sounds


it sounds like one of your door switches is setting off the alarm. Or you hood or trunk switches.

Anti-Theft -Perimeter The perimeter anti-theft system consists of the following:
  • door lock cylinder disarm switches
  • liftgate lock cylinder disarm switch
  • generic electronic module (GEM)
  • door open warning lamp switch
  • pulse stretcher module (wagon only, is located between the rear license plate housing and bracket)
  • keyless entry remote transmitter
  • hood switch/bracket assembly
-----------------------------------------------------------------------------------------------------------------------
Principles of Operation
Perimeter Anti-theft
The perimeter anti-theft feature provides an audible and visual alarm when unauthorized access to the vehicle is detected. When an intrusion is detected by any door or liftgate ajar switches, or the hood and trunk tamper switches it sends a ground signal to the GEM. When the GEM receives a signal indicating intrusion into the vehicle, the GEM supplies a ground signal to the horn control relay and the park lamps relay. The relay closes, supplying the power which activates the horn and the park lamps. The pulse stretcher module applies to wagons only. Due to the distance between the liftgate disarm switch and the GEM, the disarm switch signal is not present long enough for the GEM to recognize. The pulse stretcher module receives pulse input when switch is turned to unlock. The pulse stretcher module holds the pulse active for about 60ms so the GEM can recognize the signal and disarm the system. The perimeter anti-theft feature does not arm until 20 seconds elapses after locking the vehicle. The perimeter anti-theft device will disarm only when
  • unlock is pressed on the keyless entry remote transmitter.
  • keyless entry keypad code is entered.
  • door, luggage compartment lid or liftgate lock cylinder is turned to unlock.
  • ignition switch position changes to run or start.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Lock cylinder disarm switches
  • Hood switch
  • Luggage compartment lid switch
  • Loose or corroded connections
  • Generic electronic module (GEM)
  • Circuitry

-----------------------------------------------------------
Door Disarm Switch Removal and Installation
  1. Disconnect the battery ground cable. Refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Disconnect the latch lever from the door lock cylinder.
    1. Remove the E-clip.
    1. Disconnect the latch lever.
  1. NOTE: The door disarm switch can be installed in more than one position. Before removing the switch from the cylinder it may be necessary to mark the position of the switch in relation to the lock cylinder.
    Remove the door disarm switch.
    • Disconnect disarm switch electrical connector.
  1. NOTE: The door disarm switch can be installed in more than one position. Use the reference marks applied in the removal procedure to index the new door disarm switch to the lock cylinder.

Jan 24, 2011 | 2005 Mercury Sable

1 Answer

My battery goes dead on my 1996 Lincoln Mark VIII overnight. I found that the lights come on by themself after I park the car. There is a clicking sound coming from the security module in the trunk when I...


security module in the trunk ???? There is no security module in the trunk . What light's come on by them self ? Park lamps , headlamps , brake lamps ,turn signals etc.... The module for anti-theft is under the right hand side of the dash . The remote keyless entry module is located in the trunk. Is this the part you hear clicking in ?
Door Lock Control Processor, Electronic NOTE: The electronic door lock control system will not function when the ignition switch is in the RUN or ACC position.
The electronic door lock control processor:
  • is located on the LH side of the luggage compartment.
  • contains a radio receiver that receives a signal from the keyless entry remote transmitter (15K601) through electronic door lock control processor antenna, and sends the appropriate command to the power door locks, the horn relay, the indicator flasher, or the anti-theft warning system.
  • is equipped with a battery backup which holds the programmed code in memory in the event the vehicle battery is disconnected.
    • Doors Do Not Lock or Unlock Using Keyless Entry Remote Transmitter
    • Circuit.
    • Electronic door lock control processor.
    • Keyless entry remote transmitter.
    • GO to Pinpoint Test B .

Aug 17, 2017 | Lincoln Mark VIII Cars & Trucks

3 Answers

LHJ001 WIRING


I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:

b94b6e9.png


Hope helped.

Oct 30, 2009 | 1996 Lincoln Continental

1 Answer

'95 Isuzu Trooper Auto Door Locks Go off by themselves


check out wiring to anti-theft keyless entry module (under centre console front right small module on top of larger one)
also checking for shorts in door wiring harness from module to door lock actuators

Jul 14, 2009 | 1995 Isuzu Trooper

1 Answer

Replaced the alternator, now anti theft won't disable


The ignition lock anti-theft switch (19A438) detects if the ignition key cylinder is broken or "slam pulled" during a theft. The ignition lock anti-theft switch is always monitored by the remote anti-theft personality (RAP) module. This allows the alarm system to be triggered in the case that the ignition lock anti-theft switch detects tampering of the ignition key cylinder (even in the event that the alarm is not active at the time).
Refer to the Section 501-14B for more details on the keyless entry remote transmitter (15K601).
The door open warning lamp switch (14018) communicates to the RAP module through the generic electronic module (GEM). This input to the RAP will cause the anti-theft alarm to be sounded if the anti-theft alarm was armed.
The door disarm switches are assembled into both LH and RH lock sets. The door disarm switch must be triggered before the mechanical lock unlocks. This is to prevent the anti-theft alarm from activating when it should have been disarmed.
The RAP module controls the anti-theft system and is the brains of the keyless entry system. The RAP module communicates with the GEM to request that the interior lights be turned ON/OFF with use of the keyless entry remote transmitter, and the GEM communicates to the RAP to inform when the door is opened. Refer to Section 418-00 for inter-module communication.
The RAP module has three wire connectors attached to it:
  • The antenna for the keyless entry remote transmitter.
  • 26 circuit connector (C256).
  • 22 circuit connector (C257).
In addition to the perimeter alarm that uses the door open warning lamp switch, the RAP module also uses the ignition lock anti-theft switch and the autolock/relock feature to prevent theft of the vehicle. For a full description of the autolock/relock system, refer to Section 501-14B .
The THEFT LED is found on the instrument panel between the tachometer scale and the needle pivot point. The LED is illuminated during prearming and flashes when armed or triggered.
Prearming and Arming the System
The system can be armed if:
  • The ignition is OFF.
  • The PANIC alarm is OFF.
  • All doors are closed.
There are two ways to prearm the system:
  • Press the LOCK button on the transmitter.
  • Open a door, press the power door lock button and close the door.
After 30 seconds the system will be armed and the theft indicator in the cluster will flash every two seconds.
Disarming an Untriggered System
An armed system will be disarmed with one of these valid actions:
  1. Pressing the UNLOCK button on the transmitter.
  1. Placing a key in the door and turning to UNLOCK.
  1. Turning the key to RUN or ACC.
The anti-theft alarm can be triggered by the following conditions:
  • The ignition cylinder is damaged with or without the RAP being armed.
  • A door is opened without disarming the armed RAP module.
The remote transmitter can activate a panic alarm which is similar to an anti-theft alarm, but does not deactivate the starter or cause the theft indicator to flash.
Disarming a Triggered System
If the system has been triggered, (the horn honks, the lights flash, and an external starter interrupt relay is engaged), the system can be disarmed by:
  1. Pressing the UNLOCK or PANIC button on the transmitter.
  1. Putting a key in the door and unlocking the door.
  1. Turning the ignition to RUN/ACC (Turning the key to RUN/ACC will not disarm an alarm that has been triggered by the ignition lock anti-theft switch.).

Apr 10, 2009 | 1997 Ford F150 Regular Cab

1 Answer

VEHICLE WONT START


Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:
  • protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
  • monitors the status of the ignition key lock cylinder.
  • is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
  • when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
  • protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
  • triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.
Once triggered, the system responds by:
  • flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
  • sounding the horn (13832).
  • disabling the starter circuit until the system is disarmed.
---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module
  • The remote anti-theft personality module is located behind the instrument panel (04320).
  • It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
  • The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.
-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove radio. Refer to Section 15-01 .
  1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
  1. Lower glove box.
  1. Remove two remote anti-theft personality module bracket retaining screws.
  1. Disconnect electrical connectors and alarm and lock system antenna (15603).
  1. Remove remote anti-theft personality module and bracket.
  1. Remove remote anti-theft personality module from mounting bracket.
Installation
  1. To install, follow removal procedure in reverse order.
  1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).

    34bdf35.gif
Components The system is composed of the following components:
  • remote anti-theft personality (RAP) module with integral antenna
  • alarm indicator LED
  • door lock cylinder switch RH, door lock cylinder switch LH
  • liftgate door lock cylinder switch (220A40)
  • hood switch (part of windshield wiper motor wiring (17A477))
  • ignition lock anti-theft switch (19A438)
The following vehicle components are also used by the anti-theft alarm system:
  • generic electronic module
  • power door lock switch (14028)
  • door open warning lamp switch (14018)
  • autolamp relay (14N089)
  • horn relay and bracket (13853) and horn (13832)
  • low beam headlamps
  • rear lamps (13404) and parking lamps (13200)
  • starter relay
  • door lock relays
  • keyless entry remote transmitter (15K601)
--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:
  1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
  2. Unlock any door with a key.
  3. Turn ignition switch to RUN or ACC.
  4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.
------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:
  • Open any door or liftgate.
  • Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
  • Dislodge the ignition key lock cylinder.
  • The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.
When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

  • low beam headlamps
  • parking lamps
  • horn
  • THEFT indicator
The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

Mar 02, 2009 | 1998 Ford Windstar

1 Answer

Car won't start


Hi, does the alarm shut off when you unlock the passenger door?
If it does not I will give you a test that you can do.
1. disconnect the harness anti-theft control module. (loctaion depend were you live USA next to fuse panel Canadian models above the glove box.) Check the continuity between Light Green/Black wire and Black wire of the anti-theft control module.
2. Continuity should not be there with the door lock in, lock or neutral position. With the door lock in-between lock and neutral position (any door) continuity should be present.
3. If continuity is as specified replace the anti-theft control module. If continuity is not as specified, check operation of the door lock switches.I will add that test at bottom.
4. If the door lock switches are ok check the continuity og LIGHT/BLACK wires between anti-theft control module and door lock switches. Check Continuity of BLACK wire between door lock switches and ground. Continuity should be present if Continuity is not present repair harness or connectors.
5. If Continuity is present, check continuity LIGHT GREEN and BLACK wire of anti-theft control module. Continuity should not be present with trunk lock in lock or neutral position. With trunk lock in-between lock and neutral position, Continuity should be present.
6. If Continuity is as specified replace anti-theft control module. If Continuity is not as specified, check operation of truck lock switches. If necessary replace trunk lock switch.
7. If trunk lock switch is ok, check Continuity og LIGHT GREEN wire between anti-theft control module and trunk lock switch. Check Continuity of BLACK wire between trunk lock switch and ground. Continuity should be present. If Continuity is not present repair harness or connectors.

DOOR LOCK SWITCHES
Disconnect 4-pin door lock switch connect (left and right front doors) With door lock in neutral, full lock or full unlock position, there should be no continuity between any terminal and BLACK wire terminal. Continuity should exist between LIGHT GREEN?WHITE wire and BLACK wire terminals with door lock in-between neutral and full lock position. Continuity should exist between LIGHT GREEN/BLACK wire and BLACK wire terminals with door lock in-between neutral and full unlock positions. If continuity is not as described, replaced door lock switch.

Hope this help its a place to start. let me know if you need anything else.

Cheers

Aug 23, 2008 | 1994 Nissan Maxima

1 Answer

Shorted overhead light


HI. The location of the
Door locking module or lighting modele or anti theft module is.
On bottom right of the luggage comparment...

I hop this work for you " Rate please. THanks."

May 27, 2008 | 1996 Audi A4

Not finding what you are looking for?
2004 Lincoln Town Car Logo

Related Topics:

1,939 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...