Question about Mercury Cars & Trucks

Open Question

1998 mercury tracer pcv valve location diagram

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 92 Answers

SOURCE: 1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location

the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Posted on Oct 21, 2008

Mike258
  • 1498 Answers

SOURCE: serpentine belt for 1998 mercury tracer

Hey there MSM,

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator. The routing diagram is on one of the radiator supports.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

  • 188 Answers

SOURCE: where is the pcv valve on the 2005 chevy trail blazer

It is located on top of the valve cover. Buy the new one and you will see what it looks like, then you will pull the hose off of it and put the new one on, 5-minutes at top to do this job.

Posted on Feb 08, 2009

gh20s
  • 343 Answers

SOURCE: pcv valve 94 v6 xle camry location

I'm not sure exactly where it is but they are always on one of the valve covers. it is shaped like an "L" and will have one vacuum hose connected to it and it inserts into a rubber grommet on the valve cover.

Posted on May 28, 2010

ZJLimited
  • 17970 Answers

SOURCE: belt routing diagram for 1997 mercury tracer?

Check this...

f307936.gif

Hope helps.



Posted on Jul 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is PCV valve located on 2008 Mercury Milan 2.3 L I4 cylinder? Do you have a diagram you could send?


On valve cover on almost all vehicles

YOU NEVER NEED TO REPLACE A PCV VALVE

EVER


They have NO EFFECT ON YOUR ENGINES PERFORMANCE

They regulate crankcase vacuum only SO FORGET IT

Aug 06, 2011 | 2008 Mercury Milan

1 Answer

How to replace pcv valve and tubing for 1998 mercury tracer


I went to my local auto parts store and bought standard hoses and a standard Mercyry PCV valve with two male ends removed the old hoses thst were forme fitted and addapted the standard hoses and valve. It took all of ten min. and saved me over $100

Oct 19, 2010 | 1998 Mercury Tracer

1 Answer

90k , timing belt new @ 80k worked fine sprayed engine with water to clean dust started and ran fine nest day started but then idled up to 4k and wouldn't idle down drove it about 5 miles and got off...


I have ran into this problem at my shop. There are 3 things that could be bad. Idle air control valve, pcv valve or the vacum hose for the pcv valve. Vicually inspect the pcv vale hoses. If you dont see a tear, spray carb cleaner around the hose, if engine idle changes there is a vacum leak in hose some where. If pcv valve and hose are ok than its your idle air control valve. You can attempt to remove part and clean it but this is only a temporary fix, Good luck.

Oct 17, 2010 | 1998 Mercury Tracer

1 Answer

Computer problems


its located below the center of the dash, heres a diagram to help pinpiont it, hope this is helpful.d3f9ae7.gif

Jan 24, 2010 | 1998 Mercury Tracer

1 Answer

Location of pcv valve on 1998 mercury mountaneer


the PCV valve is is typically located in the valve cover near the brake booster-4.0L pushrod V6. On a 5.0L V8 engines, the PCV valve is located at the back of the intake manifold.

Dec 12, 2009 | 1998 Mercury Mountaineer

2 Answers

Need to know location of blower relay to be able to repair car


its under your hood engine bay area usually on the fender. ITLL BE A LITTLE BLACK BOX. with a cover on top.open cover and you will see relays and some big fuses.

Oct 07, 2009 | 1998 Mercury Tracer

1 Answer

I need a diagram of a how to install a serpentine belt on a 1998 Mercury Tracer with air.


1998 MERCURY TRACER - L4 2.0L 1989cc 122ci GAS FI N P

Belt Routing Diagram / Multiple Accessory, w/A.C.

8e6e46f.jpg


More details HERE

I hope help you (remember rated this help) Good luck.

Sep 18, 2009 | 1998 Mercury Tracer

2 Answers

98 Mercury Tracer idle drops at a dead stop and continues to run rough at normal driving speeds. Freeway or in town. Changed plugs / wires/ fuel filter and IAC motor. No changes in performance. Any...


Could be either the ignition coil or an injector problem whereby the latter could be caused by impending failure of the on-board computer.
Check with any chain parts store in your area by phone and ask if they offer a free code check for your car.
Even without a check engine light, you may have a code (or more) stored in the ECU. 

Mar 17, 2009 | 1998 Mercury Tracer

1 Answer

1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location


the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Sep 25, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...