Question about 1996 Chevrolet Express

1 Answer

Wiring digram for wiring trailer plug on 1996 Chev pu 3500

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a fuse diagram for a 2006 Ford F250 2WD. My lights all work great on the PU but when I connect the trailer the lights work but no brake lights or turn signals.


If all the lights work properly with the trailer wiring not connected then the truck itself is fine. If attaching the trailer wiring causes the lights to permanently stop working on the truck then you are blowing a fuse and it will need to be replaced. Your owners manual will show you where the fuse panel is. You should be able to check the wiring plug at the back of the truck to be sure it is working properly with a test light and a helper. If the power for signals/brakes etc are not all working at the plug, then trace back and fix these. If all is good at the truck's plug, then the trailer wiring must be faulty. Again, go through it and fix anything that is broken or corroded. Of course it goes without saying, make sure all the bulbs are good.

Nov 02, 2014 | Cars & Trucks

1 Answer

Brake and blinker fuses blowing when u hook up trailer


Usually a wiring problem - the wiring on your truck connector may not match the pinout on the trailer plug.

Oct 10, 2017 | 2000 Dodge Ram 3500

1 Answer

No power going to glow plugs 1996 chev 3500 6.5


the glow plug relay is at fault. the best thing to do is. buy a haynes manual for your specific vehicle at any auto parts store. they are based on a complete teardown of vehicle. this book should help. have a good day !! to be sure the glow plug is bad.

Jan 18, 2011 | 1996 Chevrolet C3500

1 Answer

2008 Dodge 3500. My right trailer signal does not work.


the problem may be in the plug on your vehicle,you need to check all the wires on the plug,one may be loose or not connected at all,if you think the problem is with the trailer you need to do the same with that plug as well.....hope this helps......cheers

Jul 19, 2010 | 2004 Dodge Ram 2500

1 Answer

TRAILER BRAKE WIRING ON 2007 3500 CHEV IT HASE TRAILER BRAKE IN DASH BUT NO POWER CUMMING OUT OF BLUE WIRE ON PLUG.


Check the plug under the truck. It is probably over the spare tire. If you still don't have power at that point, check all fuses. go to http://www.etrailer.com/faq-wiring.aspx for more detailed info.

Nov 16, 2009 | 2007 Chevrolet Silverado 3500HD New Cars

1 Answer

How do you take off a rear door panel 05 chev pu


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 14, 2009 | 2000 Chevrolet 3500

2 Answers

I have tail lights on pu but none on trailer when hooked up i replaced the plug wired same as old one no trailer tail lights I have turn & stop lights I have checked the fuse and still no juice to plug...


if you have nothing to the receptacle on the truck but the tail and stop lights still work, look under the rear of the truck near the receptacle , there should be a connection in to the main wiring harness...maybe its unpluged,dirty or corroded

Jul 10, 2009 | 1995 Ford F250

1 Answer

No power to trailer brake lights on 2002 chev 3500. tail & turn lights work


You have running, & turn signals but no brake lights? If you have 2 separate lens for turn & stop, that's your problem. Isn't yours amber for signals & red for stop? if yes, you'll need to stop at autoparts store or trailer/RV place and get a little converter that you wire in to correct that.

May 03, 2009 | 2002 Chevrolet Express

1 Answer

1996 chev pu 1500 4wd acuator wired to stay on always.


Your best bet would be to take it to your local mechanic or yourself if you feel comfortable with it and first correctly rewire the actuator. If the chain still keeps slipping after this which it probably will you need a t-case rebuild.

Jan 29, 2009 | 1996 Chevrolet Tahoe

1 Answer

Truck and trailer wiring


The fuses and relays for the trailer are isolated from the regular running lights, I believe the fuses and relays are in the underhood power ditribution box.

Jul 12, 2008 | 1996 Ford Explorer

Not finding what you are looking for?
1996 Chevrolet Express Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...