Question about Toyota Cars & Trucks

Open Question

Flywheel torque settings for a Toyota 2E engine

Flywheel torque settings for a Toyota 2E engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Posted on Jul 01, 2008

Benimur
  • 6966 Answers

SOURCE: toyota 2e engine

Hi,

The only positive way to check if the oil pump is working and therefore there is correct oil pressure is to temporary install a non-electrical oil pressure gauge that uses a small copper tubing to sample the oil/pressure and drive a needle on the gauge. Depending on temperature, idle should register about 20+psi. Having done this and confirmed that indeed there is sufficient oil pressure then it may simply be a defective oil sending unit. Otherwise, no or low oil pressure at idle is an indicator that the engine needs to be opened up again.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.


Posted on Jul 24, 2008

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 2 Answers

SOURCE: 1986 toyota corolla 2E engine high fuel consumption

why does my normal rpm always bug down when the engine start?and when I started to use the air con, the rpm was playing. It doesnt go on a certain point. it always range at 800rpm then it will down to 700. what am I might do to solve this probem?

Posted on Mar 13, 2010

rohdd
  • 283 Answers

SOURCE: 89 toyota pickup torque specs. for flywheel and

Thoroughly clean the flywheel bolts. Coat the first 3 or 4 threads of each bolt with sealant. Install the flywheel, aligning the previously made marks. Install the bolts finger-tight.
Tighten the bolts in a crisscross pattern and in several passes to the correct tightness:

  • 22R/22R-E manual trans-80 ft. lbs. (108 Nm)
  • 14-20 ft-lb for the clutch cover and
  • 50 ft-lb for the transmission mounting bolts.
Since you have the flywheel off, be sure and inspect the rear main seal. Now might be a good time to replace it. Be sure the rear flange of the flywheel is clean before re-install.
Be sure to inspect or, better yet, replace the bronze pilot bushing. I f you don't know how to get it out leave a comment. J


Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is really appreciated for the FREE answering of your question.

Posted on Feb 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All torque settings on a 4af toyota


cylinder head bolts
stage1-20NM
stage2-40NM
stage3-60NM

MAIN BEARINGS
stage1-30NM
stage2-60NM

BIG END BEARINGS
stage1-25NM
stage2-49NM

FLYWHEEL
78NM

Sep 05, 2016 | Toyota Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Torque setting for yaris t1


here you go an on line page with all your specs just write down the ones you need. off save page for off line viewing.
http://www.allwidewallpapers.com/2007-toyota-yaris-engine-specifications/MjAwNy10b3lvdGEteWFyaXMtZW5naW5lLXNwZWNpZmljYXRpb25z

Jun 22, 2016 | 2007 Toyota Yaris

1 Answer

Torque setting specs for toyota 1.3 2e engine.


This will be in your shop manual, and if you are doing work that requires torquing the head bolts you really should buy a cheap shop manual.

Apr 27, 2016 | Toyota Cars & Trucks

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Torque specification


petrol engine alloy head 65lbs
main bearing caps 80lbs
big end bolts 40lbs

Nov 21, 2013 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...