Question about Toyota Cars & Trucks

Open Question

Torque settings 99 corolla starter - Toyota Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: need torque settings for 1985 4A corolla cylinder head

hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque setting on 1989 corolla valve cover


No. Let good sense and experience guide you. If you need a torque figure try an internet generic chart and halve the maximum listed for the size and type of bolt.

Torque figures aren't just there to avoid snapping bolts or to achieve the maximum clamping force.
Using torque figures is also about tightening a number of bolts uniformly to avoid distortion.

Feb 06, 2015 | 1989 Toyota Corolla

1 Answer

Torque settings on a toyota corolla 1996 5a-fe engine


Get a Hanes manual from PepBoys for your vehicle.You'll find all your answers there.

Apr 19, 2014 | 1996 Toyota Corolla

1 Answer

Full engine torque settings for toyota corolla 1.4 vvti 2001 model


main bearing
tighting in the following stages:
22Nm then 44 Nm then 45 degree then 45 degree
big end bearing
20 Nm then 90 degree

Apr 05, 2014 | 2001 Toyota Corolla

1 Answer

What is the torque setting of mains, bigends and cylinder head of 1zz Toyota corolla 140i


Torque:
- Connecting rod (big ends). Tighten bolts in several steps. 1st stage 29 NM, 2nd stage, rotate further 90 degrees
- Main cap bolts (crank shaft). Tighten bolts in several steps. 1st stage 44 NM. 2nd stage, further tighten 90 degrees.

Oct 06, 2013 | 2005 Toyota Corolla

1 Answer

Where is the starter? and How do I replace it?


Hello! It's under the engine on the right side under a cover...See diagram below...Guru...saailer
  1. DISCONNECT BATTERY NEGATIVE TERMINAL
  2. REMOVE ENGINE UNDER COVER RH...

    1. REMOVE STARTER ASSEMBLY...
    (a)Disconnect the starter connector....(b)Open the terminal cover....(c)Remove the nut, then disconnect the starter wire...(d)Remove the 2 bolts, then remove the starter....
    1. INSTALL STARTER ASSEMBLY Torque: 37 Nm (378 kgf-cm, 27 ft-lbf) for bolt 9.8 Nm (100 kgf-cm, 7 ft-lbf) for nut...
    2. INSTALL ENGINE UNDER COVER RH...
    3. CONNECT BATTERY NEGATIVE TERMINAL Torque: 5.4 Nm (55 kgf-cm, 48 in-lbf)...


1_9_2012_9_36_14_am.gif

Jan 09, 2012 | 2004 Toyota Corolla

1 Answer

I need the torque settings for a Toyota Corolla 1995 model 4afe engine TORQUE SETTINGS FOR THE CYLINDER HEAD? PLEASE PLEASE HELP


cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Feb 22, 2011 | 1995 Toyota Corolla

1 Answer

What are spark plug torque specs for 2003 toyota corolla


Toyota do not have a specific torque setting for spark plugs in the master workshop manual,they say "hand tight, plus 1/8th turn"(using a plug socket and ratchet handle).

Oct 31, 2010 | 2003 Toyota Corolla

3 Answers

How to Replace the Starter in a 1999 Pontiac Grand


starter is located on the engine block down below.

Removal & Installation To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.
  1. Remove or disconnect the following:
    • Negative battery cable
    • Radiator lower air deflector
    • Torque converter cover
    • Electrical connections from the starter
    • Starter motor
To Install:
  1. Install or connect the following:
    • Starter motor and torque the bolts to 32 ft. lbs. (43 Nm)
    • Starter solenoid BAT terminal
    • Starter solenoid S terminal
    • Torque converter cover and torque the bolts to 89 inch lbs. (10 Nm)
    • Radiator lower air deflector and torque the bolts to 15 ft. lbs. (20 Nm)
    • Negative battery cable
Starter removal/installation – 3.1L & 3.4L engines 9306zg15.gif

Starter removal/installation -3.8L engine 9306zg17.gif

Jul 15, 2010 | 1999 Pontiac Grand Prix

1 Answer

'03 Toyoya


I'll presume it's a US 1ZZ:

  1. REMOVE ENGINE UNDER COVER RH
979dc2f.gif
  1. REMOVE STARTER ASSY
    1. Disconnect the starter connector.
    2. Remove the nut and disconnect the starter wire.
    3. Remove the 2 bolts and starter.
  1. INSTALL STARTER ASSY Torque: Bolt 37 Nm (378 kgf.cm, 27 ft.lbf) Nut 9.8 Nm (100 kgf.cm, 7 ft.lbf)

Sep 12, 2009 | 2003 Toyota Corolla

1 Answer

Need torque settings for 1985 4A corolla cylinder head


hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Jan 14, 2009 | 1985 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...