Question about 2009 Chevrolet Traverse

1 Answer

Screw will not come out it keeps turning rear tail light singal

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

Using screw drive try to get something carefully under head of screw and pry up while turning left,, lefty lousy,,, righty tighty


When re installing use a strand of copper wire looped in and out of hole and tighten screw back into hole,,, break off excess copper strand

Posted on Nov 10, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

Rear lights don't come on with headlights brake lights work hazards & turn singals work


The tail lights are on a separate circuit bad bulbs or fuse labelled TM or tail lights in fuse box.

Oct 19, 2013 | Chevrolet Colorado Cars & Trucks

1 Answer

Left turn signal won't work, light bulbs are good, fuse is good. when the emgency flasher is on only the right will blink. The singal will turn on and stay on without blinking when the brake petal is...


Replace the circuit board on the left rear tail light ***.This can be purchased at a NAPA auto parts store.(this is where the bulbs are fasten into)

Oct 25, 2011 | 2004 Chevrolet Tahoe

2 Answers

No break lights ,tail lights on a 1999 suberban check the fuse and they are all good when i turn my lights on and put on the turn singal and press on the break they start blinking very fast when i thouch...


it sounds like a ground problem...sounds like the ground is trying to go through the bulbs to make connection....check all ground wires battery, engine and rear frame...

May 27, 2011 | 1999 GMC Suburban

1 Answer

HOW DO I CHANGE MY REAR BRAKE LIGHT?


Open the Back and unscrew the tail light screws on the inside of the door jam. The whole tail light assembly will come out. Twist the bulb socket counter clockwise, pull the bulb out. Place new bulb in the sockett, place sockett back in tail light and turn clockwise till it stops. Place tail light back in hole, put screws back in to door jam to hold tail light in.

Feb 26, 2011 | 2007 Suzuki XL-7

1 Answer

How to change a tail light


1. Remove the two screws at the outside back of the tail light cover
2. loosen the tail light cover from the two clips at the front of the cover by gently prying it toward the rear. Fingernails worked for me. The bottom clip seemed easier. If it is too tight, try a screwdriver near the bottom, then near the top prying toward the rear of the car.
3. the top light is the backup lamp (white), and the bottom light is the brake/turn/rear light (red).
4. rotate the lamp 1/3 turn to remove and replace.
5. test.
6. replace the cover by aligning the screw holes then pushing the cover into the clips and replacing the screws.

Oct 16, 2010 | 2005 Ford Freestyle

1 Answer

How to get the tailight fixture off to change the bulb


Here, just follow this steps:

1. Locate the tail light on the rear of your vehicle. They are located on each corner and light up when you apply your brakes or turn signal.

2. If applicable, remove any mounting screws on the outside of the tail light.

3.
Open the trunk of your vehicle and locate the back of the tail light.

4.
Remove the socket and bulb from the back of the tail light by turning and pulling.

5.
Remove the tail light mounting screws or nuts.

6.
Push the tail light out from behind.

Feb 06, 2010 | 2006 Suzuki Grand Vitara

1 Answer

Electrcal problem on a 94 grand am


it more then lokly the turn singal swicth all the rear lights run through it

Jun 02, 2009 | 1994 Pontiac Grand Am

2 Answers

Tail lights dont work but bake and turn singals do


did you also check the fuses under the hood, there is a 20 amp out there that feeds that circuit.

Feb 02, 2009 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
2009 Chevrolet Traverse Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...