Question about 2007 Toyota 4Runner

Open Question

2007 RX350 with check light and vsc light on, started running real rough today and codes coming up are C1201,C1223,1249. any ideas

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mecanica03
  • 874 Answers

SOURCE: My 2007 Toyota Tundra 4.7l shows VSC OFF lights

check air filter for dirty , how many miles or kms have your car? , maybe need to replace spark plugs, try to reset the ecu for a momentany malfunction, remove the negative battery terminal few minutes and reconnect,start engine and drive, check if lights goes off , please write me

Posted on Jul 05, 2009

  • 21 Answers

SOURCE: 2004 Toyota 4Runner, Regarding The VSC TRAC and VSC OFF lights

Check your switches for the VSC, some get bumped on (due to their location) and some get stuck in the "on"position.

Posted on Aug 04, 2009

  • 1 Answer

SOURCE: running real rough and uneven at idle and slower speeds

Seems like this car have the same symptom wherever it is, I have this trouble as well, I did the tune up, injection cleaning, change spark plugs and spark plugs wires, change the air filter, change the engine mounting but still the same trouble :(

Posted on May 04, 2010

  • 14585 Answers

SOURCE: I am getting check VSC system and Engine light,

I have worked on this and they put a clutch system ( only thing I can think of to call it) On the cam shaft to give it variable speed. It is like having to replace the timing belt. this is a costly fix. not for the novice . have it check at a garage, it could be an electrical problem, the on I did was. The part I believe was $300.00 plus. So take it to a mechanic that you can trust

Posted on Nov 12, 2010

  • 294 Answers

SOURCE: 2008 highlander has check engine light and vsc off light on. what is problem.. how do i resolve this?

need codes to help, take it to a local auto parts that scans it for free and summit then to try helping you

Posted on Oct 10, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hy.I'm Adrian.I have a lexus is250 from 2006 and I just changed the battery and apear the VSC CHEK LIGHT and ENGINE LIGHT.and a c1201 and p2118 error codes.please someone can help with some suggestin


Code P2118 throttle control motor is set when voltage to the motor gets below 4 volts, so perhaps this was set with old dead battery. code C1201 is a vague engine control code, and the VSC vehicle stability code is set anytime you hook up a scan tool other that the dealer's special unit. You must reset the zero point calibration for this to go away. Use your scan tool to erase all codes to see if any come back. This will not turn off the VSC light, however. Follow below procedure to reset zero point calibration.

Zero Point Calibration - "VSC" and "VSC Off" Lights - 2002 SC430 - SOLVED
________________________________________
Friends,
For the benefit of any 2002 Lexus SC430 owners, I'll post the following item dealing with "Zero Point Calibration".
After hours of troubleshooting, I came to the hypothesis that the instructions MIGHT be different from 2002 - 2005 and 2006 - 2010 models. Below are the instructions I followed and WORKED on my 2002 SC430.
If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."

Oct 29, 2016 | Lexus Cars & Trucks

1 Answer

What needs to be done for error code C1201


Hi on the code that I have for that,it says.

ABS inlet coil LF circuit short to ground.

Hope this was some help,all the best.

Sep 02, 2016 | 2006 Lexus Is 250

1 Answer

2007 Lexus rx350. get codes off. C1201 and Po 352


The codes will reset themselves as soon as you fix the problems causing them and drive the car for three complete drive cycles.

Feb 21, 2016 | Lexus Cars & Trucks

1 Answer

Toyota Avalon 2006 all Check Engine, VSC, Traction Control lights are on


that code 356 is a bad coil. if it is completely dead than you now have a 5 cylinder car.... very bad not only on mpg but also on the life of the engine. when you have a "dead hole" it can affect the other cylinders and you have misfire codes for all 6..... this could mean you simply need a tune up or that there is something affecting all cylinders. check for a vacuum leak after the air flow sensor, or a ruptured fuel pressure regulator (remove the vacuum line at the regulator and smell for gas cause there should not be gas on that side of the diaphragm) fouled spark plugs, clogged exhaust or catalytic converter, stuck open or dirty EGR valve to name a few. change that #6 coil first and at least inspect or change the spark plugs... c1201 relates to a communication stop between ECU's , don't assume that as the vsc lights etc were illuminated then that is the system that is faulty. It is most likely that the fault is within the engine system but with vehicles equipped with vsc all systems are linked so a fault with one will log a code in all others ( normally a communication stop code as you have)
I would advise fixing the engine codes first then get the other systems checked out

Mar 31, 2014 | 2006 Toyota Avalon Limited

1 Answer

ENGINE CODES


Whenever engine fault codes set, VSC is disabled and lights come on. P0020 shows failing cam shaft position sensor , recommend replace clear codes and recheck. gas spill was coincidental.

Dec 24, 2013 | 2007 Toyota FJ Cruiser

1 Answer

Getting message CHECK VSC with engine warning and traction lights on permanently.


Whenever the check engine light comes on it also turns on the trac and the vsc, if figures the trac and vsc can not operate properly if the engine is not running correctly, when check eng light turns off the rest will also, the first thing to do is have the computer scanned, there will be stored codes, these codes will tell you where the problem is, many auto part stores will scan it and give you the codes, if you get the codes i could help you further good luck.

Sep 29, 2010 | 2007 Lexus ES 350

2 Answers

2007 lexus rx350 ,vsc light on and check engine light is flashing


First check and make sure your gas cap is tight, if this does not resolve the problem read below.
A vacuum hose has become disconnected, more than likely due to having your air filter replaced. The VSC and Check engine light typically don't come on until after 150-200 miles after the vacuum hose was pulled out.
The fix: on the right-hand-side of the engine compartment behind the big plastic housing that holds the air filter you will find a black rubber hose that is not connected to anything. Squeeze the finger clamp on the hose and slide the hose back onto the half inch nipple on the back of the air filter's plastic housing.
In order for the VSC and Check engine light to be turned off, you will need to open the fuse box, right-side of the engine compartment, and pull the 20 amp EFI fuse for 10 seconds. This will reset the system. The fuse location is marked on the lid of the fuse box, also I believe the EFI fuse is the only 20 amp fuse
. This will help. Thanks, please keep updated. please do rate the solution positively .thank you for using fixya


Dec 29, 2009 | 2007 Lexus RX 350 FWD

3 Answers

VSC OFF, Check engine and traction control lights are on


I would suggest having your mechanic scan the computer for viable trouble codes. WIthout that information, it is hard to determine the exact cause of your problem.

However, my experiences with the Tundra leads me to suggest that you have a bad Mass Air Flow Sensor...A concise scan and any codes would alow us to really help you out a lot better.

Sep 17, 2009 | 2007 Toyota Tundra

3 Answers

My 2007 Toyota Tundra 4.7l shows VSC OFF lights


check air filter for dirty , how many miles or kms have your car? , maybe need to replace spark plugs, try to reset the ecu for a momentany malfunction, remove the negative battery terminal few minutes and reconnect,start engine and drive, check if lights goes off , please write me

Jul 04, 2009 | 2007 Toyota Tundra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...