Question about 1996 Toyota RAV4

1 Answer

I need the flywheel bolt torque for my rav 4 - 1996 Toyota RAV4

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Toyota Master
  • 545 Answers

20 ft.lbf/27 n,m,install grey bolt then the black

Posted on Oct 14, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 202 Answers

SOURCE: 1999 toyota rav 4 engine oil cooler bolt torque setting

INSTALL OIL COOLER
-clean the oil cooler contact surface on the oil cooled mounting
-install a new O-ring to the oil cooler.
-temporarily install the oil cooler with the nut
-apply a light coat of engine oi on the threads and under the head of the relief vale
-install the plate washer and union bolt. torque 78Nm (800kgfcm, 58 ft lbs.)
-tighten the nut,torque 8.8Nm (90kgfcm, 78 inch lbs.)
-connect the 2 water bypass hoses to the oil cooler.

HOPE THIS CAN HELP.

Posted on Apr 26, 2010

Testimonial: "Great work thanks for the info."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

How do i remove flywheel away from torque


it is not a flywheel but a flexi plate
there will be 3 or 4 bolts facing back from the block going through the plate into nuts in the front of the torque converter
you will probably only get to one at a time and as you remove a bolt you will have to turn the flex plate until the next one comes into position

Oct 10, 2015 | Cars & Trucks

1 Answer

2001 tiburon


Torque converters are bolted up to the flywheel or flexplate. Probably 4 or 6 bolts from the flywheel engine side into the torque converter.

May 03, 2012 | 2001 Hyundai Tiburon

1 Answer

Need to know the torque on the bolts from the flywheel to the torque convertor


Install torque converter attaching bolts. Tighten bolts to following torque:

40 ft. lbs. (54 Nm) with 9.5 in. 3-lug converter
55 ft. lbs. (74 Nm) with 9.5 in. 4-lug converter
55 ft. lbs. (74 Nm) with 10.0 in. 4-lug converter
270 in. lbs. (31 Nm) with 10.75 in. 4-lug converter

I hope this helps.

Aug 26, 2011 | 2002 Jeep Liberty

1 Answer

How to install a clutch kit on my 1994 mitsubishi mighty max


Disconnect the battery, disconnect the Hydraulic Line from the Slave Cylinder, Remove the Starter (2 bolts, 2 wires. Bolts are 14mm, 1 wire is 12mm, 1 plugs in), Remove the Driveshaft(s) (4 12mm bolts) Remove the 6 bolts from the bellhousing (4 are 14mm, 2 are 10mm)
Remove the bolt from the Transfer Case Mount, 12mm (only if it's a 4WD, if it's 2WD this doesn't apply), remove the 2 bolts that hold the Transmission Mount to the Crossmember (12mm or 14mm, it varies)
Slide the transmission back on the crossmember, away from the engine, I recommend running a ratchet strap across the frame to balance the transmission.
Remove the Pressure Plate from the Flywheel (Six 10mm bolts), Inspect the Pilot Bearing (if it needs replaced, you'll need to remove the Flywheel which is held on with six 18mm bolts, drive out the old bearing and drive in the new one, reinstall the flywheel, using Threadlocker on the bolts, torque the bolts to 100 ft lbs) Install the new clutch disc and Pressure Plate, with the centering tool inserted through the disc into the pilot bearing. Use thread locker on the pressure plate bolts and torque them to 20 ft lbs. Remove the centering/alignment tool after you've bolted it together
Remove old Throw Out bearing from input shaft on the transmission and slide the new one on. Slide the Transmission forward (make sure the input shaft slides into the pilot bearing, don't force the transmission into place or you could damage the clutch disc or break the input shaft) Torque the Bellhousing Bolts to 40 ft lbs (4 14mm bolts), Torque the 2 10mm bolts to 14 ft lbs, Install the Starter (torque bolts to 23 ft lbs), Reconnect Hydraulic Line to Slave Cylinder. Torque Transmission Mount Bolts to 30 ft lbs.
Reinstall Driveshafts, torque bolts on flange/yoke to 40 ft lbs. Fill Clutch Master Cylinder with DOT-3 Brake & Clutch Fluid, Open Bleeder Screw on Slave Cylinder and bleed the air out of the system, close bleeder screw.
Reconnect the wires to the Starter, Reconnect the battery.

Aug 24, 2011 | Mitsubishi Mighty Max Cars & Trucks

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

3 Answers

Dose the flywheel come off with the transmission or dose on bolt first. if so where?


The transmission has to be removed to replace the flywheel/flexplate. Think of it as a bologna sandwich. The flywheel is the bologna. The flywheel is bolted to the crankshaft on the engine. (I'm assuming it's an automatic transmission) the torque converter (or clutch assembly) is bolted to the flywheel, and the transmission (or bell housing) is bolted to the engine block. So it's sandwitched in there. Hope that helps.

Oct 07, 2010 | Dodge Caravan Cars & Trucks

1 Answer

1999 toyota rav 4 engine oil cooler bolt torque setting


INSTALL OIL COOLER
-clean the oil cooler contact surface on the oil cooled mounting
-install a new O-ring to the oil cooler.
-temporarily install the oil cooler with the nut
-apply a light coat of engine oi on the threads and under the head of the relief vale
-install the plate washer and union bolt. torque 78Nm (800kgfcm, 58 ft lbs.)
-tighten the nut,torque 8.8Nm (90kgfcm, 78 inch lbs.)
-connect the 2 water bypass hoses to the oil cooler.

HOPE THIS CAN HELP.

Apr 26, 2010 | 1999 Toyota RAV4

1 Answer

How many bolts connect the flywheel to the torque converter?


6 bolts connect the flywheel to the crankshaft
If it has an automatic transmission the flexplate or flywheel has 6 bolts to connect it to the crankshaft and 4 more bolts to connect to the torque connverter

Jul 25, 2009 | 1984 Ford Bronco II

2 Answers

Angle Torque settings head bolts


Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Jan 28, 2009 | 2000 Renault Sportwagon

Not finding what you are looking for?
1996 Toyota RAV4 Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...