Question about 2002 Ford Windstar Cargo

1 Answer

Windshield wipers will not turn off we had to pull the fuse we have replaced the switch and the relay... any suggestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Ford Master
  • 615 Answers

You will probably find the wiper motor has water in the circutry dry motor with a hair dryer if possible it may work ok if itdoes you need to seal the unit so water doesnt get in it again.. If you cant seal it or drying it doesn't help replace wiper motor. if you find this helpful please leave good feed back

Posted on Oct 16, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 221 Answers

SOURCE: Windshield wipers wont come on or fluid

You might have a bad wiper motor, you can try checking for voltage at the wiper motor connector, if your getting voltage at the connector replace the wiper motor.

Posted on Apr 02, 2009

  • 561 Answers

SOURCE: Windshield wiper will not turn off unlessfuse removed/vehicle off

suspect a shortcircuit in the stalk switch.
1has moisture or rain got into the switch? see if problem goes after a few days
2. use WD40 or contact cleaner into the part of the switch where the cables connect to the stalk you may have to open up the steering column or possible with thin straw nozzle supplied with the can.

3. switch is defective and needs to be replaced.

Posted on Nov 13, 2009

babaphat
  • 24 Answers

SOURCE: Windshield wiper relay

this might be a connection/ currosing problem. Check the windshild wiper relay for loose wires and then take apart the connection. Clean them up and put back together. also check your fuses.

Posted on Nov 24, 2009

moparownr
  • 667 Answers

SOURCE: 1998 Ford F150. windshield wipers,interior

check to see if you have corrosion in the fuse box or the GEM module, by removing the fuse box completely, disconnect the battery, take out the two screws and two 8mm bolts that hold the fuse box in, it will take some maneuvering to get it positioned right to disconnect the two wiring harnesses from the fuse box, they are bolted through the middle. Once removed, take the GEM module off the back of the fuse box and look for what would be something like the same corrosion you would see on your battery posts, usually one of these components is corroded and causing the problem, my buddy got a replacement fuse box for his from a wrecking yard for only 15 dollars, with all the fuses and relays. If you have this corrosion, then you probably have a windshield leak at the lower left hand corner of the windshield, it lets water drip onto the fuse box and GEM module. Hope this helps, let me know

Posted on Dec 07, 2009

Testimonial: "Mr. Guru, It was the GEM module. Thank you for helping with my problem. "

01fordeb
  • 1033 Answers

SOURCE: 1998 ford expedition front windshield washer

fuse for washer pump, can you here the pump, if not then power to pump isn't present. Check the fuse for it.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

I'm driving in rain, wipers working good, all of a sudden they quit! I drive for 15 min, check again, they work for a while, then quit again...what in the problem?


If your not familiar with automotive electronics an module control of components , I suggest you take it to the dealer . They have the tools to diagnose this type problem !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper PCB relay


?€¢
Wiper high PCB relay


?€¢
Windshield wiper motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
WPR fuse 25 A


?€¢
WSW fuse 10 A


Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....

Dec 20, 2015 | 2008 Chevrolet Impala

1 Answer

Wipers dont work


This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper 1 relay


?€¢
Wiper 2 relay


?€¢
Wiper diode


?€¢
Windshield wiper motor


?€¢
Windshield washer pump


?€¢
Windshield washer nozzles


?€¢
Windshield washer solvent container


?€¢
Windshield wiper arm and blade assemblies


?€¢
Windshield wiper transmission


?€¢
WIPER/SW 10A fuse


?€¢
WIPER 25A fuse


Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

Dec 05, 2015 | Cars & Trucks

1 Answer

I think the multi-function switch is bad on my 2005 Ford Taurus SE.The windshield wipers are functioning continuously.The fuse box is located under my hood. Which fuse can I pull to "kill" the wipers?


open the bonnet open the black fuse and relay plastic box. Listen for the relay kicking in or you may be able to feel the relay or look on the cover for the relay location. Pull out the relay .
I have a faulty headlight switch myself and had to hard wire my head lights on with a jump wire. The relay is in my pocket until I can get a new headlight indicator stalk. You may be able to jump wire the wipers with spade connectors to work with a jump wire in case you need wipers until you can replace the wiper stalk .
It could be a stuck relay causing the fault rather than the switch. you need to check if switch causes voltage to turn off accross the relay coil in the relay mount block.

Jul 08, 2015 | Ford Cars & Trucks

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

2 Answers

WIPERS WON'T TURN OFF


Turn signal switch sounds defective or it may simply be the wiper relay is stuck. Locate and pull the relay.

Nov 22, 2013 | Ford Escort Cars & Trucks

2 Answers

Back windshield wiper won't turn on


The rear wiper has a dedicated fuse. It's the 10A R/WIPER fuse in the relay block. This supplies power to the rear wiper and washer switch and the rear wiper control unit. That unit also gets power from the 20A AUDIO (!) fuse in the engine room fuse box. If the fuses are OK, the ignition switch is in the ON position, and the rear wiper and washer switch is turned on the rear wiper should work. If not check all the components described to find where the loss of power is occurring

Nov 15, 2012 | 2005 Kia Sorento

2 Answers

Windshield wipers will not turn off, I've replace the turn signal/wiper switch and still not turning off


Sounds like the PARK SWITCH within the WIPER MOTOR is at fault, Only way to beat it is relay the motor. Hope this helps

May 08, 2009 | Cadillac DeVille Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...