Question about 1998 Toyota Tacoma

Open Question

After replacing ignition, can not shift out of park.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 merc grandmarkee wont go into park wont start will start if you wiggle in nutral


Park neutral safety switch could be bad , also the shift interlock safety system .
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.
Condition Possible Source Action
  • Shift Interlock System Does Not Release or Lock Properly
  • Circuitry open/shorted.
  • Blown fuse.
  • Damaged stoplight switch.
  • Damaged shift lock actuator.
  • GO to Pinpoint Test A .

PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE OR LOCK PROPERLY A1 CHECK ELECTRON IGN FUSE
  • Check Fuse 5 (5A) located in fuse junction panel.
Is fuse OK?
Yes No GO to A3 . GO to A2 . A2 CHECK FOR SHORT TO GROUND
  • Turn ignition switch OFF.
  • Remove Fuse 5 (5A).
  • Disconnect shift-lock actuator connector C203 located to the right of steering column.
  • Measure resistance of the Circuit 1003 (GY/Y) between the correct terminal of Fuse 5 (5A) and ground.
Is resistance greater than 10,000 ohms?
Yes No REPLACE Fuse 5 (5A). GO to A3 . SERVICE Circuit 1003 (GY/Y) wire between fuse junction panel and shift-lock actuator. A3 CHECK POWER SUPPLY FROM FUSE 5 (5A)
  • Reinstall Fuse 5 (5A).
  • Turn ignition switch to RUN.
  • Measure voltage on Circuit 1003 (GY/Y) wire and ground.
Is voltage greater than 10 volts?
Yes No GO to A4 . SERVICE Circuit 1003 (GY/Y) wire between interior fuse panel and shift-lock actuator. A4 CHECK POWER SUPPLY FROM FUSE 28 (15A)
  • Turn ignition switch OFF.
  • Disconnect connector C2016.
  • Turn ignition switch ON.
  • Measure voltage on Circuit 10 (LG/R) and ground.
Is voltage B+?
Yes No GO to A5 . SERVICE Circuit 10 (LG/R) for open. RESTORE vehicle and RETEST system. A5 CHECK WIRE BETWEEN STOPLIGHT SWITCH AND SHIFT-LOCK ACTUATOR
  • Turn ignition switch OFF.
  • Disconnect shift-lock actuator connector C203.
  • Apply brake pedal.
  • Measure voltage on Circuit 810 (R/LG) wire and ground.
Is voltage greater than 10 volts with brake pedal applied and less than 1 volt with brake pedal released?
Yes No GO to A6 . SERVICE Circuit 810 (R/LG) wire between stoplight switch and shift-lock actuator. A6 CHECK SHIFT-LOCK ACTUATOR GROUND
  • Measure resistance of Circuit 57 (BK) and ground.
Is resistance less than 5 ohms?
Yes No REPLACE shift-lock actuator. SERVICE BK wire.

Mar 30, 2017 | Cars & Trucks

1 Answer

2005 cts won't sift out of park, press the brake pedal and start the car, just won't shift out of park


You probably have a problem with

Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components.
• The automatic transmission shift lock control solenoid
• The brake switch
• The rear integration module (RIM)
• The transmission control module (TCM) or powertrain control module (PCM)
With the ignition ON, battery positive voltage is supplied to the automatic transmission shift lock control solenoid from the ignition 3 relay. The automatic transmission shift lock control solenoid is controlled by the rear integration module. When the rear integration module (RIM) receives a class 2 serial data message from the transmission control module (TCM) or powertrain control module (PCM) indicating that the shift lever is in the PARK position the rear integration module (RIM) grounds the automatic transmission shift lock control solenoid control circuit. This causes the solenoid to energize mechanically locking the shift lever in the PARK position. When the driver presses the brake pedal the rear integration module receives the brake applied signal and turns off the ground to the automatic transmission shift lock control solenoid control circuit. This allows the shift lever to be moved out of the PARK position.

Shift Lever Does Not Move with Brake Pedal Depressed

2
Apply the parking brake and block the wheels.
Turn ON the ignition, with the engine OFF.
Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, observe the TCC brake switch parameter in the transmission data display list.
Press and release the brake pedal several times.
Does the TCC brake switch status turn ON and OFF with the brake pedal?
YES - Go to Step 4
NO - Go to Stop Lamps Inoperative in Lighting Systems
4
With a scan tool, observe the brake to shift control parameter in the rear integration module data list.
Press and release the brake pedal several times.
Does the brake to shift control status turn ON and OFF with the brake pedal?
YES - Go to Step 5
NO - Go to Step 8
5
Turn OFF the ignition.
Connect a test lamp between the automatic transmission shift lock control solenoid supply voltage circuit and the automatic transmission shift lock control solenoid control circuit at the automatic transmission shift lock control solenoid.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the brake to shift control ON and OFF several times while observing the test lamp.
Does the test lamp turn ON and OFF with each command?
YES - Go to Step 7
NO - Go to Step 6
6
Test the automatic transmission shift lock control solenoid control circuit for and open or short to battery voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 11
NO - Go to Step 8
7
Inspect for poor connection at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 11
NO - Go to Step 9
8
Inspect for poor connections at the harness connector of the rear integration module (RIM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Yes - Go to Step 11
NO - Go to Step 10
9
Replace the automatic transmission shift lock control solenoid. Refer to Automatic Transmission Shift Lock Actuator Replacement .
YES - Did you complete the replacement?
NO - Go to Step 11
--
10
Replace the RIM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
YES - Did you complete the replacement?
NO - Go to Step 11
--
11
Operate the system in order to verify the repair.
Did you find and correct the condition?
YES - System OK
NO - Go to Step 2

Mar 25, 2017 | Cadillac CTS Cars & Trucks

1 Answer

Holden cruze 2009 key stuck in the ignition won't go to off position , can't get it out of park .What is the problem ?


Is it shifter on the floor ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

GM had problems with these ! Has a TSB - technical service bulletin !
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will remove voltage from the shift lock solenoid:
- The ignition is in the ON position.
- The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
- The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
During remote start operation, the BCM will energize the shift lock control circuit, locking the shift lever in the PARK position.
Replaced shifter on a cobalt , broken plastic part inside , wouldn't press on micro switch to disengage ! Found replacement shifter at auto slavage yard .$20.00 US

Sep 03, 2016 | Holden Cars & Trucks

1 Answer

My 2003 GMC ENVOY won't shift out of park


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
Shift Lever Does Not Move with Brake Pedal Depressed ?

2

  1. Turn ON the ignition.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Step 7
Go to Step 4

4

  1. Turn OFF the ignition.
  2. Leave the automatic transmission shift lock control switch disconnected.
  3. Connect a test lamp between the A/T shift lock control solenoid supply voltage circuit at the automatic transmission shift lock control solenoid and a good ground.
  4. Turn ON the ignition with the engine OFF.
Does the test lamp illuminate?

5

  1. Turn OFF the ignition.
  2. Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and a good ground.
  3. Turn ON the ignition with the engine OFF.
Does the test lamp illuminate?
Go to Step 6
Go to Step 9

6

  1. Turn OFF the ignition.
  2. Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and the park lock solenoid ground circuit.
  3. Turn ON the ignition with the engine OFF.
Does the test lamp illuminate?
Go to Step 8
Go to Step 11

7

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Step 13

8

Inspect for poor connections at the harness connector of the park lock/automatic transmission shift lock control solenoid assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Step 12

9

Repair the open or high resistance in the park lock solenoid ignition 1 voltage circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

10

Repair short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

11

Repair the open or high resistance in the park lock solenoid ground circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

12

Important: Depress the button on the side of the shift lock actuator. With the button is depressed, cycle the plastic straw within the shift lever 3 to 5 times. The straw should move smoothly and freely except near the top of the travel where additional force will be required to mechanically actuate the park lock mechanism inside of the shift lock actuator. If there is stick/slip or abnormal friction while cycling the plastic straw or if the straw is altogether stuck in the lever, the entire control assembly (shifter and shift lock actuator) needs to be replaced. Refer to Transmission Control Replacement . If there is no abnormal friction, replace the shift lock actuator. Refer to Automatic Transmission Shift Lock Control Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jul 09, 2016 | GMC Cars & Trucks

1 Answer

2004 pontiac sunfire wont shift out of park


Problem with shift interlock system .
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The body control module (BCM)


?€¢
The powertrain control module (PCM)

With the ignition in the ON position, battery positive voltage is supplied to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid receives a ground from the BCM. When the automatic transmission shift lock control solenoid is energized, the shift lever mechanically locked in the PARK position. When the driver presses the brake pedal the PCM sends a class 2 serial data message to the BCM. The BCM turns OFF the ground control circuit and this de-energizes the automatic transmission shift lock control solenoid. When the automatic transmission shift lock control solenoid is de-energized, the shift lever may be moved out of the PARK position. The BCM determines transaxle shift lever position through a class 2 serial data message from the PCM. The PCM receives inputs from the park/neutral position switch and determines shift lever position. When the BCM receives this information and determines that the shift lever is out of the PARK position, the automatic transmission shift lock control solenoid ground is opened.

1

Did you perform the A Diagnostic System Check - Automatic Transmission Shift Lock Control?
Go to Step 2
Go to Diagnostic System Check - Automatic Transmission Shift Lock Control

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF.
  4. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Step 4
NO - Go to Step 5

4

Test the A/T shift lock control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 6

5

Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 7

6

Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 8

7

Replace the automatic transmission shift lock control solenoid. Refer to Transmission Control Replacement in Automatic Transaxle-4T40-E/4T45-E.
Did you complete the replacement?
Go to Step 9
--

8

Replace the body control module (BCM). Refer to Body Control Module Replacement in Body Control System.
Did you complete the replacement?
Go to Step 9
--

9

Operate the system in order to verify the repair.
Did you find and correct the condition?
System OK
Go to Step 2

Jun 29, 2016 | Pontiac Cars & Trucks

1 Answer

How do I get shifter out of park?


The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The body control module (BCM)


?€¢
The powertrain control module (PCM)

The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock control solenoid:
?€¢
The ignition is in the ON position.


?€¢
The PCM sends a class 2 message to the BCM indicating the transmission is in the PARK position.


?€¢
The BCM determines the brake pedal is not applied according to the stop lamp switch.

When the ignition is in the ON position, the ignition 1 fuse supplies voltage to the automatic transmission shift lock control solenoid as the BCM supplies a ground to the control circuit, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the ground of the control circuit OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
Your best bet is to take it to the dealer ,may have DTC'S
DTC B2707 Gearshift Unlock Circuit Low
The body control module (BCM) controls the automatic transmission shift lock control solenoid by providing a controlled ground to the automatic transmission shift lock control solenoid. The BCM utilizes a smart driver to monitor the voltage and current flow of the automatic transmission shift lock control solenoid control circuit. DTC B2707 will set when the BCM detects a short to ground when the solenoid is in the OFF state.
DTC B2708 Gearshift Unlock Circuit High
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

  1. Turn OFF the ignition.
  2. Install a scan tool.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. With a scan tool, command the Brake to Shift Relay output control parameter On.
  6. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Step 4
Go to Step 6

4

  1. With the scan tool, observe the Brake Switch parameter in the powertrain control module (PCM) data display list.
  2. Press and release the brake pedal several times while observing the scan tool.
Does the brake input display Applied and Released with the brake pedal operation?
Go to Step 5
Go to Diagnostic Starting Point - Lighting Systems in Lighting Systems

5

With the scan tool observe the TR Sw. parameter in the body control module (BCM) data list.
Does the scan tool indicate PARK position?
Go to Step 9
Go to Scan Tool Data List in Engine Controls - 3.4L

6

  1. Turn OFF the ignition.
  2. Disconnect the harness connector of the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Step 7
Go to Step 8

7

Test the controlled ground circuit of the automatic transmission shift lock control solenoid for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 9

8

Inspect for poor connections as the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 10

9

Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 11

10

Replace the automatic transmission shift lock control solenoid. Refer to Shift Lock Control Solenoid Replacement .
Did you complete the replacement?
Go to Step 12
--

11

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?
Go to Step 12
--

12

Operate the system in order to verify the repair.
Did you find and correct the condition?
System OK
Go to Step 3

Your best bet

Jan 11, 2016 | 2005 Chevrolet Equinox

1 Answer

Stuck in park will not shift


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid.


?€¢
The automatic transmission shift lock control switch.


?€¢
The park/neutral position switch.

With the ignition in the ON position, battery positive voltage is supplied to the park/neutral position switch. When the transmission is in the PARK position the contacts in the park/neutral position switch are closed. This allows current to flow through the switch to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid, locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, causing the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid. The system consists of the park lock solenoid. With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.
Shift Lever Does Not Move with Brake Pedal Depressed
DEFINITION: Transmission shift lever will not move out of the PARK position with the ignition ON and the brake pedal pressed.

1

Did you perform the Symptoms - Automatic Transmission Shift Lock Control tests and all the necessary inspection?
Go to Step 2
Go to Symptoms - Automatic Transmission Shift Lock Control

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 6
Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 7
Go to Step 5
Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 9

6

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 8

7

Repair the short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 10
--

8

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?

Oct 13, 2015 | 2006 Hummer H2

1 Answer

The gear shifter on my 1998 Pontiac SE coupe will not unlock so I can take the car out of park


Do you have column or floor shifter ?
All automatic transaxle models use an electric park lock system. Within the housing assembly, a lock cylinder is connected to an actuator which rotates and engages on the electric park lock solenoid. When the floor-shift lever is not in the park position, the actuator disengages from the electric park lock solenoid slider. This allows the lock cylinder to move to the lock position. With the shift lever in PARK and the lock cylinder in LOCK, the actuator cam is positioned against the electric park lock solenoid slider. This prevents the shift lever from shifting out of the PARK position.
The column-shift automatic transaxle model uses a flexible cable actuator instead of an electric park lock system. One end of the cable is attached to the gate assembly. The other end of the cable is attached to the column mounted housing assembly. This system functions similarly to the floor-shift ignition lock system.
The manual transaxle model uses a push button lock cylinder. A clutch start switch is used. The clutch pedal must be pressed before the engine will crank. Refer to Park Lock System Check .
CAN you turn the key on ?
The gear selector does not shift out of PARK with the brake pedal depressed and the ignition switch in RUN.
Automatic Transmission Shift Lock Control Always On with Ignition in Run
Action
Value(s)
Yes
No

1

Was the BTSI System Check performed?
--
Go to Step 2
Go to Automatic Transmission Shift Lock Control System Check

2

Is this a column shift vehicle?
--
Go to Step 3 yes
Go to Step 4 no

3

  1. Move the gear selector to the PARK position.
  2. Disconnect the automatic transaxle control connector
  3. Turn the ignition switch to RUN.
  4. Connect the test lamp between terminal B and ground.
Does the test lamp light?
--
Go to Step 4
Go to Step 8

4

  1. Disconnect the brake switch connector C2.
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 5
Go to Step 8

5

Is the brake switch adjusted properly?
--
Go to Step 6
Go to Step 7

6

Replace the brake switch.
Is the repair complete?
--
System OK
--

7

Adjust the brake switch.
Is the repair complete?
--
System OK
--

8

  1. Disconnect the BTSI solenoid connector (column shift vehicles) or disconnect the automatic transaxle control connector (console shift vehicles).
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 9
Go to Step 10

9

Repair the short to power in CKT 1135.
Is the repair complete?
--
System OK
--

10

Test for sticking or binding in the shift linkage.
Does the shift linkage stick or bind?
--
Go to Step 11
Go to Step 12

11

Repair the shift linkage.
Is the repair complete?
--
System OK
--

12

Replace the BTSI solenoid (column shift vehicles) or replace the automatic transaxle control (console shift vehicles).
Is the repair complete?
--
System OK
Go to Step 1

May 18, 2015 | Pontiac Cars & Trucks

1 Answer

96 F250 can't shift out of park


NOTE: Your vehicle is equipped with a

brake-shift interlock feature. This

feature prevents you from shifting

from P (Park) unless you have the

brake pedal depressed. (The ignition

must be in the ON position.) If you

cannot shift from P (Park) with the

brake pedal depressed:


1. Apply the parking brake.

2. Remove the key.

3. Insert the key and rotate one position
clockwise (ignition in the OFF position).

4. Apply the brake pedal and shift to N

(Neutral). (If the vehicle is shifted to P

(Park), you must repeat the previous steps.)

5. Start the vehicle.


If you need to shift out of P (Park) by using the

alternate procedure described above, it is

possible that a fuse has blown and that your

brakelamps may also not be functional.


WARNING

DO NOT DRIVE YOUR VEHICLE UNTIL

YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.

check fuse 13 based on the attached diagram.

If this fuse is bad replace it. If it is not bad, blows again, or continues to be stuck in park then you need a new brake interlock switch that can be found on the brake pedal up underneath the dash.mustang_guru_2.jpg

Jan 12, 2011 | Ford F-250 Cars & Trucks

3 Answers

2006 Chevy Impala stuck in park


When you turn ignition on it releases a cable that is attached to the shifter also the shifter has a solenoid attached to it that is released when you step on the brake. Both times that I had the problem of button stuck and cant shift out of park the solenoid was sticking and wouldnt release .

Dec 20, 2008 | 1998 Land Rover Discovery

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...