Question about Cars & Trucks

1 Answer

1990 Buick electra - it turns over good but I'm not getting any fire to the sparkplugs. what do I need to check?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 175 Answers

Crankshaft senser

Posted on Oct 14, 2013

  • Chuck Evans Oct 15, 2013

    I changed that and still nothing. what do I need to check next? also, thank you for your help!! I appreciate it!



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 184 Answers

SOURCE: firing order, 1990 Buick LaSabre

Here ya go

Posted on Dec 14, 2008

  • 2920 Answers

SOURCE: Heater Core Replacement for 1986 Buick Electra Park Ave

there is no easy way to change out a heater have to take the bottom part of the dash loose and that takes some doing. once you get the bottom of the dash apart you will see the heater core.then you have to go under the hood and unhook both water lines that run to it, you should then be able to pull the heater core out and install the new one

Posted on Feb 09, 2009

  • 53 Answers

SOURCE: have a 1979 buick electra limited 350 5.7


Posted on Jun 12, 2009

  • 376 Answers

SOURCE: Buick 1990 Buick Electra/Pk Ave

ck the lamp housing for corosion inside and wire condition outside, then use a test light to ck for 12vdc, and continous ground. if ok suspect headlamp switch...etc

Posted on Sep 15, 2009

  • 3092 Answers

SOURCE: what is the firing order of a 1987 buick electra

Hope this helps.


Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Not getting any fire

Have you tested the system for fault codes, if not do so by following the instructions at this LINK Also check the fuel pressure at the engine fuel delivery rail to the injectors

Aug 30, 2012 | 1990 Buick Electra

1 Answer

1990 buick park avenue digital dash don't work

Where is the temp gauge on 1990 Buick park ave

Aug 05, 2012 | 1990 Buick Electra

1 Answer

I need the firing order for a 3.8L 1986 Buick park ave? Coil Pack.

The diagram below is for the 3.8L (231ci) is below. The firing order is: 1-6-5-4-3-2

1986 Buick Electra 3.8L Firing Order:

Oct 09, 2011 | 1986 Buick Electra

1 Answer

We can not figure out why my 1990 dodge ram keeps back firing we replaced the plugs, button, cap,wires and coil and its still back fires

You need to get an exact firing order diaghram for your make,model and engine,

call any autoparts store, and they will give you the firing order for your truck, if one

or more wires are wrong, can cause the engine to backfire or run bad. also make

sure you have the correct gap on your sparkplugs. check and set the timing,

if needed, the auto parts will also have the timing marks position. good luck!

Jul 10, 2011 | 1990 Dodge Ram

1 Answer

I get no fire to the sparkplugs when turning engine over could it be the coil

check to see if fire from coil an body grounds are a must check those an if fire is at coil check cap an button distributer has a pickup coil most likley

Dec 20, 2010 | 1990 Mitsubishi Mighty Max

1 Answer

Trying to check sparkplugs on 2001 buick lesabre

An OBD-2 scanner will pinpoint which cylinder has the miss fire ( as long as the check engine lite is on. Try that and see which cylinder is bad first.. Thanks

Mar 16, 2009 | 2001 Buick LeSabre

1 Answer

Buick 1990 Buick Electra/Pk Ave Replaced right 9004 head light for low beam failure but no light shines. High beam works fine. Help please. email:

ck the lamp housing for corosion inside and wire condition outside, then use a test light to ck for 12vdc, and continous ground. if ok suspect headlamp switch...etc

Mar 13, 2009 | 1990 Buick Electra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15360 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides