Question about 1994 Mazda 626

1 Answer

Engine light is on and thermostat temperature was almost on h.

I checked if there was water in the radiator and I didnt have to add any in it.

Posted by on

  • josh1111 May 11, 2010

    have you scanned it for codes?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 114 Answers

It may be a stuck thermostat, but it would overheat and come out of the resivour over flow if that is actually happening. it may be a bad temp sensor. most cars have two . One for the gauge and one for the engine computer. Or the wiring for the sensors is bad. If the car is dead cold like in the morning before it runs, turn the key to run,dont start, check the gauge does it go to hot?

Posted on Apr 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water level is ok but light comes on 2002 impala


Friend,
If it is the temperature light ( not the check engine light) you may wish to check and see if the engine is actually hot.
(Be advisesd. An overheated engine is really serious! )
With the engine not running and cold, and the car level, take off the radiator cap very slowly to relieve the pressure, be certain the radiator is full, and then start the car.
Stand back in case the radiator blows antifreeze out.
Now start he car, and with the engine running, and when the temperature light is on, very carefully feel or smell the radiator and top radiator hose. If these are not hot, you problem may be a stuck thermostat. If the thermostat is stuck, you should sense the heat by smelling and listening to the motor.
If you have an overheating issue, please refrain from driving the car until it is fixed, or you could totally destroy the motor.
Also, there are 2 electric blower fans behind your radiator. One is for engine temperature, one is for the air conditioning circuit.
If the temperature light comes on, one of the blower fans should be running. If neither is, that may be your problem.
Be sure to leave your heater/air conditioner off during this test.
The most common problem is a bad temperature sensor for the fan, then a bad fan itself. After that, a stuck thermostat.
Blessings on your figuring this out.

Apr 13, 2015 | 2002 Chevrolet Impala

3 Answers

Engine overheating i have replaced the radiator has plenty of water


replace thermostat.then bleed coolant system, this is how you do it.fill the cooling coolant system with 50 / 50 dexcool and water to raise boiling point,straight water will evaporate boil away cause engine to overheat catch fire thats why you need 50 / 50 mixture antifreeze and water.to bleed coolant system first fill coolant system until coolant stay at the full cold mark on the the coolant overflow jug,then you start engine allow it to idle,place the heater and ac control in any ac setting except max and the temperature control to the highest setting,run engine until lower hose to water pump is hot. with the engine hot run the engine speed up to 3000 rpm and allow it return to idle, repeat this 5 times. slowly open the bleed valve on the thermostat housing or look for bleed valve at the water pump heater hose.open bleed valve for 15 seconds to expel any trapped air.then top off the coolant as necessary,and when top radiator hose hot thermostat open up.keep adding cooling to overflow until coolant level stop at full cold mark dont over fill coolant.if engine seem like overheating while looking at cooling gauge turn off engine wait a while until cool off add more coolant until coolant level stay stable and dont drop any.when open radiator overflow cap use large rag over the radiator cap to keep from getting scald open radiator cap a little at a time but dont open radiator cap until engine cool down first.replace the radiator overflow cap, thermostat,and engine coolant temperature sensor and check the cooling fans fuses and relays see what happens.

Aug 18, 2012 | 1998 Oldsmobile Intrigue

2 Answers

I have a 1999 oldsmobile intrigue with a 3.5 engine and it is overheating what might be the problem?


It's usually the thermostat, I woud pressure test the cap. It may need to be flushed. Are the fans working? Is there a 50/50 mix of anti-freeze

Sep 11, 2011 | 1999 Oldsmobile Intrigue

3 Answers

I replaced my radiator on my 2004 with a 2.2 and it seems like the thermostat is not opening. It can not get the air out. It seem to just to over heat and push the coolant out. Randy


REPLACE THERMOSTAT IF TOP COOLANT COOLANT HOSE GOING TO RADIATOR IS HOT TO TOUCH THERMOSTAT OPEN. TO BLEED COOLANT SYSTEM FIRST YOU NEED TO ADD COOLANT TO THE COOLANT OVER FLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND STAY AT FULL COLD MARK.WAIT 3 MINUTES IF COOLANT DROPS ADD MORE COOLANT UNTIL COOLANT STAY AT FULL COLD MARK.WITH RADIATOR OVER CAP OFF CRANK ENGINE FOR MINUTE WATCH COOLANT LEVEL AT OVERFLOW JUG.IF COOLANT DROPS ADD MORE COOLANT IN THE OVERFLOW JUG.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW BACK ON THE RADIATOR CAP TO OVERFLOW JUG.WHILE ENGINE IDLING WATCH TEMPERATURE GAUGE WHEN TEMPERATURE START CLIMBING TURN OFF ENGINE WAIT A WHILE KEEP FROM GETTING SCALDED.WHEN COOLANT COOL DOWN SOME. PLACE A LARGE RAG OVER THE COOLANT OVERFLOW JUG OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED, THEN REMOVE CAP ADD MORE COOLANT IN THE OVERFLOW JUG TO THE FULL COLD MARK.THEN REPEAT THE PROCESS SCREW BACK ON THE COOLANT OVERFLOW RADIATOR PRESSURE CAP.THEN START ENGINE WATCH TEMPERATURE GAUGE WATCH COOLANT TEMPERATURE GAUGE WHEN COOLANT TEMPERATURE START RISING TURN OFF ENGINE AGAIN WAIT UNTIL ENGINE COOL DOWN ENOUGH TO KEEP FROM GETTING SCALDED TAKE PLACE LARGE RAG OVER RADIATOR CAP WHICH IS THE COOLANT OVERFLOW JUG CAP OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED ADD COOLANT UNTIL AT FULL COLD MARK. WHEN YOUR COOLANT LEVEL STOP DROPPING.AND TOP RADIATOR HOSE VERY HOT THERMOSTAT OPEN AND AIR IS OUT THE COOLANT SYSTEM. MAKE SURE YOUR COOLANT OVERFLOW JUG HAS COOLANT IN IT,WHEN ENGINE COOL DOWN CHECK COOLANT OVERFLOW JUG KEEP COOLANT LEVEL AT FULL COLD MARK.BECAUSE IF OVERFLOW JUG IS EMPTY THATS A SIGN RADIATOR COOLANT LEVEL LOW.WHEN OVERFLOW JUG EMPTY IT WILL ALLOW AIR GET IN THE COOLANT SYSTEM AND CAUSE CAR TO OVERHEAT.WHEN REPLACING THERMOSTAT ALSO REPLACE THE RADIATOR CAP ON THE COOLANT OVERFLOW JUG.

Aug 09, 2011 | 2004 Oldsmobile Alero

3 Answers

We just replaced the radiator and the thermastat but the needle still goes to hot


replace the temperature sending unit. Its right there by the thermostat. You can get this at any auto parts store. just need an open end wrench to change it. they do go bad(found out the hard way several years back). I hope this helps you

Jan 13, 2011 | 1999 Plymouth Voyager

1 Answer

How do i replace the water thmostat 99 6 cylider


WELL YOU NEED TO DRAIN COOLANT LEVEL BELOW THERMOSTAT LEVEL.YOU HAVE TO DISCONNECT MAF SENSOR LOOSEN AIRDUCT 2 LARGE CLAMPS LOOSEN REMOVE 4 SCREWS TO AIR FILTER COVER LIFT UP REMOVE COVER. THEN REMOVE AIR FILTER AND HOUSING, FIRST DISCONNECT MAF SENSOR.YOU HAVE TO DISCONNECT THROTTLE CABLE AND SHIFT CABLE.YOU HAVE TO DISCONNECT REMOVE THROTTLE BODY COOLANT HOSES DISCONNECT IDLE SPEED CONTROL VALVE CONNECTOR AND DISCONNECT TPS SENSOR CONNECTOR. THEN REMOVE THROTTLE BODY ASSEMBLY. YOU NEED TO BUY NEW THROTTLE BODY COOLANT HOSES AND NEW THROTTLE BODY GASKET FOLLOW TOP COOLANT HOSE TO ENGINE BLOCK.NOW YOU SEE CAN AND REMOVE THE THERMOSTAT HOUSING REPLACE THE THERMOSTAT.BESURE TO HAVE EXTRA COOLANT ON HAND.BLEED COOLANT SYSTEM WHEN DONE.TO BLEED COOLANT SYSTEM REMOVE RADIATOR CAP ON OVERFLOW JUG.THEN OPEN BLEED SCREW ON THE WATER PUMP BYPASS HOSE PIPE JUST A LITTLE.POUR COOLANT IN THE OVERFLOW JUG UNTIL LEVEL STOP DROPPING.STOP AT COLD MARK ON JUG.CLOSE BLEEDER SCREW ON WATER PUMP BYPASS HOSE PIPE.CRANK VECHICLE CHECK FOR LEAKS. START UP ENGINE LET IDLE FEW MINUTES THEN CHECK COOLANT LEVEL ADD MORE UNTIL UNTIL LEVEL STOP DROPPING.PUT RADIATOR CAP BACK ON OVERFLOW RESERVOIR. LET ENGINE IDLE WATCH COOLANT TEMPERATURE GAUGE.WHEN GAUGE START CLIMBING. TURN OFF ENGINE WAIT FEW MINUTES TAKE A LARGE RAG OPEN RADIATOR JUST A LITTLE YOU HEAR HISS NOISE.WHEN PRESSURE STABILIZE DONT GET SCALDED BECAREFUL.OPEN CAP LITTLE MORE.IF COOLANT PRESSURE STILL BOILS OUT WAIT 20 MINUTES ADD MORE COOLANT TO RADIATOR OVER FLOW WHEN COOLANT LEVEL STOP DROPPING.PUT RADIATOR CAP BACK ON START VECHICLE UP LET IDLE UNTIL THERMOSTAT OPEN. THEN FEEL TOP RADIATOR HOSE FEELS HOT THERMOSTAT OPEN WATCH TEMPERATURE GAUGE.IF GAUGE TEMP START CLIMBING TURN OFF ENGINE WAIT A WHILE.CHECK AND ADD MORE COOLANT.WHEN THE ENGINE CAN IDLE TEMP GAUGE STOP CLIMBING YOU HAVE BLEED COOLANT SYSTEM.KEEP CHECK ON COOLANT LEVEL.

Dec 29, 2010 | 1999 Oldsmobile Alero

3 Answers

Cooling system problems


The engine is kept cool by a liquid circulating through the engine to a radiator. In the radiator, the liquid is cooled by air passing through the radiator tubes. The coolant is circulated by a rotating water pump driven by the engine crankshaft. The complete engine cooling system consists of a radiator, recovery system, cooling fan, thermostat, water pump and serpentine belt.

Check the coolant level in the recovery bottle or surge tank, usually mounted on the inner fender. With the engine cold, the coolant level should be at the FULL COLD or between the FULL HOT and ADD level. With the engine at normal operating temperature, the coolant level should be at the FULL HOT or HOT mark. Only add coolant to the recovery bottle or surge tank as necessary to bring the system up to a proper level. On any vehicle that is not equipped with a coolant recovery bottle or surge tank, the level must be checked by removing the radiator cap. This should only be done when the cooling system has had time to sufficiently cool after the engine has been run. The coolant level should be within 2 in. (51mm) of the base of the radiator filler neck. If necessary, coolant can then be added directly to the radiator.

While you are checking the coolant level, check the radiator cap for a worn or cracked gasket. If the cap doesn't seal properly, fluid will be lost and the engine will overheat.

Worn caps should be replaced with a new one.

Periodically clean any debris; leaves, paper, insects, etc. from the radiator fins. Pick the large pieces off by hand. The smaller pieces can be washed away with water pressure from a hose.

Carefully straighten any bent radiator fins with a pair of needle nose pliers. Be careful, the fins are very soft. Don't wiggle the fins back and forth too much. Straighten them once and try not move them again. It is recommended that the radiator be cleaned and flushed of sludge and any rust build-up once a year. If this has not been administered within the stated time, this may be why your vehicle is overheating at this time. Have the Radiator flushed asap if this is the case.

Now, if the coolant level is proper and, the cap is in fair or good condition, i would advise to move in the direction of the cooling fans and sensors as well. These fans are vital to the cooling process as well. The cooling fans must cycle in intervals to keep the coolant cool during stop and go driving or, long idle. They are also very important during the operational period of the AC during travel as well. i recommend inspecting the cooling fans while the engine is running. they should cycle during the running period. if thsi is not the case, you will need to test the operational value of these devices. The test procedure follows below


TESTING


1. If the fan doesn't operate, disconnect the fan and apply voltage across the fan terminals. If the fan still doesn't run, it needs a new motor.

2. If the fan runs, with the jumpers but not when connected, the fan relay is the most likely problem.

3. If fan operates but a high current draw is suspected continue with the following ammeter TESTING.

4. Disconnect the electrical connector from the cooling fan.

5. Using an ammeter and jumper wires, connect the fan motor in series with the battery and ammeter. With the fan running, check the ammeter reading, it should be 3.4-5.0 amps; if not, replace the motor.

6. Reconnect the fan's electrical connector. Start the engine, allow it to reach temperatures above 194°F and confirm that the fan runs. If the fan doesn't run, replace the temperature switch.



Ok, Now we will move on to the next possible issue. The water pump. ok, due to the fact that your pump is driven by the drive belt, you will need to start the engine and listen for bad bearing, using a mechanic's Stethoscope or rubber tubing.

* Place the stethoscope or hose on the bearing or pump shaft.
* If a louder than normal noise is heard, the bearing is defective.

Replace the pump in this case.

You will also notice leakage around the pump housing if the seal has failed as well. this will strain the impeller and, ruin the pump.

Now. the last area of concern will be the thermosta. this is the most common issue that will inflict overheating in many vehicles. The thermostat is used to control the flow of engine coolant. When the engine is cold, the thermostat is closed to prevent coolant from circulating through the engine. As the engine begins to warm up, the thermostat opens to allow the coolant to flow through the radiator and cool the engine to its normal operating temperature. Fuel economy and engine durability is increased when operated at normal operating temperature.


There are several ways to test the opening temperature of a thermostat.

One method does not require that the thermostat be removed from the engine.

* Remove the radiator pressure cap from a cool radiator and insert a thermometer into the coolant.
* Start the engine and let it warm up. Watch the thermometer and the surface of the coolant.
* When the coolant begins to flow, this indicates the thermostat has started to open.
* The reading on the thermometer indicates the opening temperature of the thermostat.
* If the engine is cold and coolant circulates, this indicates the thermostat is stuck open and must be replaced.

The other way to test a thermostat is to remove it.

* Suspend the thermostat completely submerged in a small container of water so it does not touch the bottom.
* Place a thermometer in the water so it does not touch the container and only measures water temperature.
* Heat the water.
* When the thermostat valve barely begins to open, read the thermometer. This is the opening temperature of this particular thermostat.
* If the valve stays open after the thermostat is removed from the water, the thermostat is defective and must be replaced.
* Several types of commercial testers are available. When using such a tester, be sure to follow the manufacturer's instructions.
* Markings on the thermostat normally indicate which end should face toward the radiator. Regardless of the markings, the sensor end must always be installed toward the engine.
* When replacing the thermostat, also replace the gasket that seals the thermostat in place and is positioned between the water outlet casting and the engine block.

* Generally, these gaskets are made of a composition fiber material and are die-cut to match the thermostat opening and mounting bolt configuration of the water outlet.
* Thermostat gaskets generally come with or without an adhesive backing. The adhesive backing of gaskets holds the thermostat securely centered in the mounting flange, leaving both hands of the technician free to align and bolt the thermostat securely in place.

Aug 08, 2009 | 1996 Ford Thunderbird LX

1 Answer

How to replace thermostat on


Do this when cool. Take radiator cap off, start the engine, turn on heat (not defrost) and now top up coolant to about an inch or 2 from top of radiator, as level drops down, and let vehicle run until the radiator fan comes on, then off, about 3 times, and add coolant as needed while it's running. After that, put radiator cap back on tight & make sure return bottle is filled to proper level. Now try that & see how heat is, temperature gauge etc, and keep an eye on return bottle level for a while. Let me know how it is.

Mar 27, 2009 | 1992 Nissan Maxima

1 Answer

Car is overheating


2 Inspect Belt Incorrectly routed, adjusted, tensioned, missing, or worn water pump belt(s). grey_line.gif 3 Inspect Oil Pan Gasket - Performance Ruptured, cracked or leaking radiator hose. grey_line.gif 4 Inspect Radiator Cap Worn or damaged radiator cap grey_line.gif 5 Inspect Thermostat Thermostat stuck closed grey_line.gif 6 Inspect Fan Blade Broken, missing, or defective fan blade(s). grey_line.gif 8 Inspect Water Pump Damaged, worn or leaking water pump. grey_line.gif 9 Inspect Intake Manifold Plenum - Perform Leaking water pump gasket. grey_line.gif 10 Inspect Cooling Fan Control Faulty cooling fan control or circuit. grey_line.gif 11 Inspect Cooling Fan Switch - Radiator Faulty radiator cooling fan switch or circuit. grey_line.gif 12 Inspect Engine Temperature Sensor Faulty engine temperature sensor or circuit. grey_line.gif 13 Inspect Temperature Switch Damaged or faulty temperature switch or temperature switch circuit. grey_line.gif 14 Inspect Fan Clutch Worn, loose or faulty fan clutch. grey_line.gif 15 Inspect Ported Vacuum Switch Damaged, leaking, or faulty ported vacuum switch. grey_line.gif 16 Inspect Radiator Obstructed radiator core or radiator cooling fins. grey_line.gif 17 Inspect Head Gasket - Performance Head gasket leaking coolant into cylinders here is a list of things to check Shaun

Nov 17, 2008 | 2000 Cadillac DeVille

1 Answer

Coolant system


Hello there,

Either an air bubble, the thermostat or the water pump.
  • Air bubble (pocket) - Just because the radiator is full, doesn't mean the engine is. When an air bubble circulates through an engine it will cause the temp gauge to swing from hot (when water is in contact with the sensor) to cold ( when air is in contact). The less water, the hotter the engine. Easiest fix - add water.
  • Thermostat - Keeps water circulating in the engine separate from the water in the radiator until it gets to a certain temperature. At that point, it opens and allows the hot engine water and the cooler radiator water to cycle. Hot to radiator, cool to engine. As the cooler water flows over the thermostat, it closes, allowing the cycle to repeat. If it opens at the wrong temp, or not at all, your engine will overheat. Water will begin to boil. Steam will make the temp gauge swing erratically.
  • Water pump - If the water pump is failing (sometimes the impeller will come of the shaft), the water will not circulate. Same results.
Troubleshoot:
  • First and foremost: BE SAFE!!! Wear safety glasses. Start this with the engine cool. When you look in the radiator, do it from an angle and as far away as possible.
  • Have a hose or a couple two liter bottles full of water.
  • Take off the radiator cap. (Do not take off if engine is hot)
  • Is the water level low? If so, top it off.
  • Make sure the transmission is in either PARK or Neutral and set the parking brake.
  • Start the engine.
  • Observe the water level in the radiator. If it drops, top it off again.
  • At first it should do nothing. The water in the engine is still cool. The thermostat is closed. As the water in the engine heats up, the thermostat will begin to open. When it does, you will notice the water level begin to surge up and down.
  • Check your temp gauge. If the gauge getting close to the 'Red Zone', the thermostat should have begun cycling before now. Go back to the radiator and check it.
  • When (if) the thermostat finally opens all the way, the water will start moving as it cycles through the system. You will be able to tell the difference.
  • If you see the water flowing, the water pump is ok.
  • If the water does not start to move and the gauge is getting close to 'Red', shut the engine down and let it cool. Do not put your face near the radiator. If the thermostat suddenly let go, The hot water, driven by steam, could erupt out of the filler hole. Replace thermostat. Rerun this test. If results are the same, replace water pump.
  • Does the water level drop at this point (air bubble)? If so, top it off while it's circulating. Adding cold water will close the thermostat. Be prepared to wait through the cycling two or three times.
  • Check the temp gauge again. Has it leveled off?
  • When you don't need to add water any more, put the cap back on. Observe the temp gauge for a few more minutes. has it stopped the erratic behavior? If so, it was an air bubble and it's gone. If not, replace the thermostat.
Let me know how it goes. If you have any other problems, click the ASK button.

Remember: Good thing come to those who Rate.

Mike

Jul 28, 2008 | 1998 Saturn SL

Not finding what you are looking for?
1994 Mazda 626 Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8755 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...