Question about Ford Cars & Trucks

Open Question

Ford 3.0L V6 Essex engine cylinder head torque settings

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

Ad
NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove a broken head bolt?


I would centre punch mark the centre of the broken stud and with a drill stand, drill a hole down the whole length of the stud, getting larger and larger as I change the bits. When I reach the last threads peel the thread out using a pick. If the thread is damaged, drill oversized to tape to fit a Hellicoil.
The largest Essex Engine was 3.4litre V6, not 3.8. The most common was the 3.0litre fitted to the Zodiac and Capri. It was a V4 with two more pistons and uses the same head bolts etc.

Jun 18, 2017 | Ford Cars & Trucks

2 Answers

I have a 2004 ford explorer xlt v6 4.0l gas. need a o2 sensor diagram. I need names and description. for example bank 1 sensor 2 after catalytic converter


https://www.google.com/search?q=1998+BMW+318i+Automatic+Torque+settings+Head+gasket&biw=1360&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwie8o3ix8_QAhUJRSYKHdIXBrkQsAQIKQ#tbm=isch&q=2004+ford+explorer+xlt+v6+engine+firing+order

Hope this helps

Bank two are the even cylinders. Follow exhaust manifold on the side. You will find an O2 sensor just after or on the manifold, before the catalytic converter. Then, look after the catalytic and you should find another O2 sensor, this is the one you mention in your post.

Nov 30, 2016 | 2004 Ford Explorer XLT

1 Answer

I need a picture for the layout of the cylinders for a 3.8 v6 ford


3.8 V6 1982 thru 2003

Ford Essex 90 degree
Windsor,Ontario


1,2,3 pass side
4,5,6.driver side

#1 & #4 at front of motor

transverse mount,then common sense
1,2,3,next to firewall

Jun 12, 2011 | Ford Lincoln Continental Cars & Trucks

1 Answer

Cylider head torque specs ford windstar 1996 3,8 cylider V6


Position the cylinder head on the cylinder block. Tighten the cylinder head bolts in 2 steps following the proper torque sequence. The first step is 37 ft. lbs. (50 Nm) and the second step is 68 ft. lbs. (92 Nm).


98c7056.gif

Oct 21, 2010 | 1996 Ford Windstar

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

2 Answers

What do you set the torque at for head bolts on a granada 2.8 v6


U tighten these in three stages here they are:
Step 1 29-40 ft. lbs. Step 2 40-51 ft. lbs. Step 3 65-80 ft. lbs.

Jan 08, 2010 | 1978 Ford Granada

1 Answer

Ford-explorer 2005 v6 petrol cylinderhead tightening torques


a part place can give you a print out on the tor spec advance or auto zone

Jan 14, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...